| Content |
The N-8000AF is an Audio interface unit designed for use with TOA's packet intercom system (IP network-compatible intercom system) that employs the packet audio technology. It has an analog audio input and output, a time synchronization contact input, and each 8 contact inputs and outputs. Connecting the unit to the LAN permits recording of conversations, chime broadcast at regular intervals (time signal) and paging broadcast to be realized. It can be mounted in an EIA equipment rack (1U size) with the use of an optional rack mounting bracket or installed on a wall using an optional wall mounting bracket.
* 0 dB = 1 V | Power Source | 220 - 240 V AC, 50/60 Hz | | Power Consumption | 7 W (max.) | | Audio Input | 1 input (transformer isolated), -58 dB* to 0 dB*, 2 kΩ, balanced
(MIC/LINE input, controllable on the software)
with input volume control knob, removable terminal block (3 pins) | | Audio Output | 1 output (transformer isolated), 0 dB*, 600 Ω, balanced, removable terminal block (3 pins) | | Contact Input | 8 inputs, no-voltage make contact input, open voltage: 24 V DC,
short-circuit current: 5 mA or less, removable terminal block (10 pins),
(1 common terminal for 4 inputs) | | Contact Output | 8 outputs, relay contact output, contact capacity: 24 V DC/2 - 500 mA,
removable terminal block (16 pins) | | Time Sync Input | 1 input, no-voltage make contact input, open voltage: 24 V DC,
short-circuit current: 5 mA or less, removable terminal block (2 pins) | | Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
Auto MDI/MDI-X compatible
Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP
Audio packet transmission system: Unicast (simultaneous paging to up to 8 zones)
Multicast (simultaneous paging to up to 191 zones)
Connector: RJ45 connector
Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software)
Quantifying bit number: 16-bit
Voice encoding method: Sub-band ADPCM, Cryptosystem
Voice packet loss recovery: Silence insertion
Audio delay time: 80 ms, 320 ms (controllable on the software) | | Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp, Signal lamp, Peak lamp | | Other | Firmware update function, System data hold function, Time of day hold facility,
Reset switch (front panel) | | Setting Method | Rack, Desk, Surface mount | | Operating Temperature | 0 ℃ to +40 ℃ (32 ゜F to 104 ゜F) | | Operating Humidity | 90 %RH or less (no condensation) | | Finish | Pre-coated steel plate, black, 30 % gloss | | Dimensions | 210 (W) × 44.3 (H) × 267 (D) mm (8.27" × 1.74" × 10.51“) | | Weight | 1.7 kg (3.75 lb) | | Accessory | Power cord (2 m (6.56 ft))…1, CD (for PC setting, maintenance use)…1,
Removable terminal plug (2 pins)…1, Removable terminal plug (3 pins)…2,
Removable terminal plug (5 pins)…2, Removable terminal plug (8 pins)…2,
Plastic foot…4, Screw for fitting plastic foot…4 | | Option | Rack mounting bracket: MB-15B-BK (for rack mounting one N-8000AF unit)
MB-15B-J (for rack mounting two N-8000AF units)
Wall mounting bracket: YC-850 |
|
The N-8000CO is a C/O interface unit designed for use with TOA's packet intercom system (IP network-compatible intercom system) that employs the packet audio technology. It has an analog central office line circuit, allowing the intercom station to make and receive calls to and from the telephone line. Connecting the unit to the LAN permits paging calls through analog subscriber line to be made and the equipment connected to the N-8000MI and N-8000DI to be controlled. It can be mounted in an EIA equipment rack (1U size) with the use of an optional rack mounting bracket or installed on a wall using an optional wall mounting bracket.
| Power Source | 220 - 240 V AC, 50/60 Hz | | Power Consumption | 7 W (max.) | | Line | Public Switched telephone networks
Number of lines: 1 line
Selective signal type: DTMF signal
Signal system: Compatible with loop start signaling
Wiring method: 1 pair of twisted pair cables | | Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
Auto MDI/MDI-X compatible
Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP
Audio packet transmission system: Unicast (simultaneous paging to up to 8 zones)
Multicast (simultaneous paging to up to 191 zones)
Connector: RJ45 connector | | Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp,
Line in-use lamp | | Other | Firmware update function, System data hold function, Time of day hold facility,
Reset switch (front panel) | | Setting Method | Rack, Desk, Surface mount | | Operating Temperature | 0 ℃ to +40 ℃ (32 ゜F to 104 ゜F) | | Operating Humidity | 90 %RH or less (no condensation) | | Finish | Pre-coated steel plate, black, 30 % gloss | | Dimensions | 210 (W) × 44.3 (H) × 267 (D) mm (8.27" × 1.74" × 10.51“) | | Weight | 1.7 kg (3.75 lb) | | Accessory | Power cord (2 m (6.56 ft))…1, CD (for PC setting, maintenance use)…1,
Mini-clamp plug (2 pins)…2, Plastic foot…4, Screw for fitting plastic foot…4 | | Option | Rack mounting bracket: MB-15B-BK (for rack mounting one N-8000CO unit)
MB-15B-J (for rack mounting two N-8000CO units)
Wall mounting bracket: YC-850 |
|
Features:
1) IP67 waterproof and dustproof (Not diving)
2) Relay Forwarding Confirmed (1750 HZ)
3) Tri-Band, Dual Display and Dual Standby
4) High & Low Power Switchover
5) Battery Saving
6) VOX Function
7) Wide/Narrow Band Selection
8) Auto-Back Light
9) Dual Band Standby
10) Time-out Timer (TOT)
11) 50 CTCSS and 104 DCS Codes
12) Voice Prompt
13) ANI Code
14) PC or Manual Program
15) DTMF Code
16) PTT-ID
17) ATUO Keypad Lock
18) Busy Channel Lock Function
19) Low Battery Warning
20) Emergency Alarm
21) Priory Scanning Function
22) U/V Cross Band Dual Watch
Functions:
●Tri-band handheld transceiver, with display function menu on the display ‘LCD’.Working Frequency:136-174MHz/400-480MHz
●High/mid/low power selectable(5 W/3 W /1 W)
●Up to 128 memory channels.
●Cross band reception/transmission
●A variety of display channel number, frequency, channel frequency, channel name, etc.
●CTCSS&DCS
●Tone end of transmission
●Function ‘VOX'(voice operated transmission).
●DTMF emergency alarm
●ANI code
●Selectable Frequency Step 2.5/5/6.25/10/12.5/20/25/50 kHz
●Frequency reverse
●Battery saving function ‘SAVE’.
●Emergency SOS sound and light alarm
●Programmable by PC.
●Broadband (Wide 25KHz)/ Narrowband(Narrow 12.5KHz), selectable..
●Commercial FM radio receiver(65 MHz~ 108 MHz).
●Display illumination and programmable keyboard.
●Built-in LED flashlight
■ Specifications are subject to change for technology improvement without notice
Package contents:
1 x radio
1 x desktop charger
1 x dual band antenna
1 x handstrap
1 x belt clip
1 x battery 4800mAh
1 x user guide |
The N-8000DI is a Direct select unit designed for use with TOA's packet intercom system (IP network-compatible intercom system) that employs the packet audio technology. It is equipped with each 32 contact inputs and outputs, and the indicators on the front panel indicate the output statuses. Connecting the unit to the LAN permits the calling station display, external equipment control, and direct selection function to be realized. It can be mounted in an EIA equipment rack (1U size) with the use of an accessory rack mounting bracket or installed on a wall using an optional wall mounting bracket.
| Power Source | 220 - 240 V AC, 50/60 Hz | | Power Consumption | 16 W (max.) | | Contact Input | 32 inputs, no-voltage make contact input, open voltage: 24 V DC,
short-circuit current: 5 mA or less, removable terminal block (20 pins)
(1 common terminal for 4 inputs) | | Contact Output | 32 outputs, relay contact output, contact capacity: 24 V DC/2 - 500 mA,
removable terminal block (32 pins) | | Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
Auto MDI/MDI-X compatible
Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP
Connector: RJ45 connector | | Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp,
Channel indication lamps (32 channels) | | Other | Firmware update function, System data hold function, Time of day hold facility,
Reset switch (front panel) | | Setting Method | Rack, Desk, Surface mount | | Operating Temperature | 0 ℃ to +40 ℃ (32 ゜F to 104 ゜F) | | Operating Humidity | 90 %RH or less (no condensation) | | Finish | Pre-coated steel plate, black, 30 % gloss | | Dimensions | 420 (W) × 44.3 (H) × 267 (D) mm (16.54" × 1.74" × 10.51“) | | Weight | 2.8 kg (6.17 lb) | | Accessory | Power cord (2 m (6.56 ft))…1, CD (for PC setting, maintenance use)…1,
Removable terminal plug (10 pins)…4, Removable terminal plug (16 pins)…4,
Plastic foot…4, Screw for fitting plastic foot…4, Rack mounting bracket…2,
Screw for mounting bracket…8, Screw for rack mounting…4 | | Option | Wall mounting bracket: YC-850 |
|
Αυτό κεντρικός σταθμός έχει σχεδιαστεί για να συνδεθεί με το IP Intercom Exchange, και προσφέρει hands-free ή ακουστικό συνομιλία υψηλής ποιότητας ήχου. Αυτός ο σταθμός μπορεί να τοποθετηθεί στον τοίχο χρησιμοποιώντας έναν προαιρετικό επιτοίχια βάση YC-280.
* 0 dB = 1 V | Power Source | 48 V DC (supplied from the IP intercom exchange (option)) | | Power Consumption | 1.8 W (at rated), 2.4 W (max.) | | Wiring Method | Non-polar one pair stranded wire system | | Transmission System | 2 wire 160 kbps echo canceller transmission system | | Signal Level | Under 0 dB* | | Speech Method | Hands-free or handset conversation | | Audio Frequency Range | 300 - 7,000 Hz | | Transmission Range | Max. 1500 m (φ0.65 mm, Loop resistance 170 Ω) | | Hands-free | Speaker: 5.7 cm cone-type, 0.6W, 8 Ω
Microphone: Omni-directional electret condenser microphone | | Handset | Receive path: Cone-type
Send path: Electret condenser microphone | | Line Connecting Terminal | RJ11 modular jack | | Installation Method | Desk/Surface mounted master station
(When mounting to the wall, use the optional YC-280.) | | Operating Temperature | 0℃ to +40℃ | | Operating Humidity | Under 90% RH (no condensation) | | Finish | Body, Handset: ABS resin, gray | | Dimensions | 148 (W) x 208 (H) x 70.5 (D) mm (excluding a curl cord section) | | Weight | 700 g | | Accessory | Connection cord (3 m)…1 | | Option | Wall mounting bracket: YC-280 |
| BAOFENG UV-5RA Portable Two-Way Radio 136-174/400-480 MHz Dual-Band Transceiver (Black)
Χαρακτηριστικά:
- Εύρος συχνοτήτων: VHF 144-148MHz & UHF 420-450MHz
- Dual-band απεικόνιση, διπλή συχνότητα. Οθόνη, Dual-Standby
- Ισχύς εξόδου: 5 /1 Watt
- 128 κανάλια
- 50 CTCSS και 104 CDCSS
- Ενσωματωμένη λειτουργία VOX
- 1750Hz Brust Tone
- Φακός LED
- Μεγάλη οθόνη LCD
- Δυνατότητα εναλλαγής ισχύος RF υψηλής/χαμηλής
- 25KHz/12,5KHz Δυνατότητα εναλλαγής
- Ειδοποίηση έκτακτης ανάγκης
- Ειδοποίηση χαμηλής μπαταρίας
- Εξοικονόμηση μπαταρίας
- Timeout Timer
- Κλείδωμα πληκτρολογίου
- Κανάλι παρακολούθησης
- ROGER SET
Τεχνικές προδιαγραφές:
- Εύρος συχνοτήτων: VHF 144-148 MHz & UHF 420-450 MHz
- Κανάλια αρ.: 128
- Σταθερότητα συχνότητας: ±2,5 ppm
- Τάση λειτουργίας: DC 7,4V
- Ισχύς εξόδου: 4W / 1W (Μέγ. 5W)
- Τρόπος λειτουργίας: Single ή semi-duplex
- Διαστάσεις (Π x Υ x Β): 100 x 52 x 32 mm
- Βάρος: 250 g (συμπεριλαμβανομένης της μπαταρίας, της κεραίας)
Περιεχόμενα συσκευασίας:
- 1 x πομποδέκτη UV-5RA
- 1 x κεραία
- 1 x μπαταρία Li-ion
- 1 x φορτιστής
- 1 x κλιπ ζώνης
- 1 x sling
- 1 x ακουστικό PTT
- 1 x εγχειρίδιο χρήστη
Features:
1) Output : 4W/1W
2) FrequencyRange: 136.00-174.00 MHz & 400.00-480.00MHz
3) Frequency Step Setting
4) High &Low Power Switchover
5) Battery Saving
6) VOX Function
7) Wide/Narrow Band Selection
8) Auto-Back Light
9) Dual Band Standby
10) Time-out Timer (TOT)
11) 50 CTCSS and 104 DCS Codes
12) Voice Prompt
13) ANI Code
14) PC or Manual Program
15) DTMF Code
16) PTT-ID
17) AUTO Keypad Lock
18) Busy Channel Lock Function
19) Dual Band, Dual Display and Dual Standby
20) Emergency Alarm
21) Priory Scanning Function
22) Relay Forwarding Confirmed (1750 HZ)
23) Low Battery Warning
24) U/V Cross Band Dual Watch
25) Dimension: 110x58x32mm
26) Packing Details: 40 Units/CTN, Carton Size: 47.5x42x50 cm N.W: 21.5 KGS, G.W:22.5KGS
| Specifications |
| Frequency Range: |
136.00-174.00 MHz |
| 400.00- 480.00MHz |
| Storage Channel |
128 |
| Step Frequency |
2.5/5/6.25/10/12.5/20/25KHz |
| Rated voltage |
DC 7.4V |
| Frequency Stability |
±2.5ppm |
| Work Temperature |
-20 ℃ to +60℃ |
| BatteryCapacity |
H-1800m Ah (Li-ion Battery) |
| BatteryLife |
About 12 Hours |
| Frequency Combination |
PLL frequency synthesis |
| Antenna Impedance |
50 Ω |
| Wok Mode |
Same Frequency simplex Operation or Different Frequency simplex Operation |
| Dimension |
110x58x32 mm (Excluded Antenna) |
| Transmitter |
| Output Power |
4W/1W |
| Modulation Mode(W/N Band) |
FM (F3E) |
| Maximum Frequency Deviation (W/N Band) |
≤5 KHz |
| Spurious Power |
≤7.5 µW |
| Adjacent channel power |
≤-65dB/≤-60dB |
| Audio Distortion |
<5 % |
| SNR |
≥-45dB/≥-40dB |
| CTSCC/DCS Frequency Deviation(W/N Band) |
0.7±0.1KHz (W), 0.4±0.1KHz (N) |
| Modulation Sensitivity |
8-12mV |
| Transmitting Current |
≤1500mA |
| Receiver |
| Sensitivity |
＜0.20 µ V (12dB SINAD) |
| Audio Power |
1 W |
| Inter modulation Interference Resistance |
≥65dB (W), ≥55dB (N) |
| Adjacent channel Sensitivity (W/N Band) |
≥65dB (W), ≥55dB (N) |
| Audio Distortion |
5 % |
| Receiving Current |
≤ 380m A |
Note:
■ Specifications are subject to change for technology improvement without notice
Package contents:
1 x radio
1 x desktop charger
1 x dual band antenna
1 x handstrap
1 x belt clip
1 x battery 1800mAh
1 x user guide
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.