| Content |
WA-215 953.132UK Wall Mount Amplifier + Media Player with Bluetooth
Compact audio controller with 2 x 15W digital amplifier built into a single gang wall plate. Powered directly from 100-240Vac mains supply, the unit can be installed into a partition wall or 47mm back box and provides a minimal yet fully functional control surface. The WA-215 has an inbuilt USB/MicroSD audio player, an FM tuner and Bluetooth receiver. Key functions are operated from the front touch panel or by using the supplied IR remote control. Connections for 2 speakers, mains power, FM antenna and an external line input are provided at the rear on screw terminal Euroblock connectors. Trigger contacts are also included for media playback and in internal doorbell sound. A complete and versatile audio solution for wall or ceiling background music speakers in the home or commercial premises.
- Power supply100-240Vac, 50/60Hz (euroblock terminals)
- Output2 x 15W @ 8 ohms (euroblock terminals)
- Audio sourceUSB / microSD player, FM tuner and Bluetooth receiver
- Auxiliary inputLeft + right line in (euroblock terminals)
- Audio formatmp3, wma, wav
- FM : tuning range87.5 - 108MHz
- Bluetooth rangeUp to 10m
- Bluetooth version4.1
- Frequency response20Hz - 20kHz (±3dB)
- THD<0.03% at 1kHz, 1WS/N ratio>98dB
- TriggerRemote playback and door bell (euroblock terminals)
- Mounting depth47mm (with adequate ventilation), 57mm back box supplied
- Dimensions86 x 86 x 50mm
- Weight150g
The box for this item contains :
- WA-215 wall mount amplifier + media player
- I.R. remote control handset
|
XB Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 400: 2x 200 W / 100 V
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans (temp. reg. variable speed)
Weight: 17 kg
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
The Crown 135MA is a high value mixer-amplifier for commercial audio. It provides 8-ohm and constant-voltage outputs (70V and 100V). Typical uses are paging, background music, and music-on-hold. The 135MA provides 3 inputs (each with a volume control) and a 35W amplifier output. Other features include priority muting, voice activated muting, phantom power, and Bass and Treble controls.
Features
- 3 inputs (each with a volume control), and one 35W amplifier output channel
- Ideal for paging, background music, and music-on-hold
- Balanced Phoenix-type mic/line input, telephone output, dual RCA stereo music inputs, screw-terminal speaker outputs
- Priority muting by VOX or external switch
- Bass and Treble controls on master output
- Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
Specifications
- Minimum Guaranteed Power into 8 ohms or 70V/100V Output: 35W
- Frequency Response (at 1 watt from line out): 50Hz to 20kHz +/-1dB; 19Hz to 34kHz +0, -3dB
- Signal to Noise Ratio (ref. to rated power, master volume at minimum):
Mic: > 58 dB.
Line: > 60 dB.
Telephone: > 60 dB.
Inputs 2 or 3 (and 4 in 160MA): > 78 dB - THD+N:
|
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
| Specification | |
|---|
| Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
| Output |
120W |
| Power Consumption |
AC operation: 158W (rated output), 66W (EN60065)
24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
| Frequency Response |
50 - 20,000Hz ±3dB |
| Distortion |
Under 2% at 1kHz, rated power |
| Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins)
MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack
AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack
AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack
AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack
TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
| Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack
LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack
MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal
SPEAKER SELECTOR:
2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/83Ω),M4 screw terminal
Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
| Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio
(Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min)
Over 76dB (Master volume: max)
Over 60dB (MIC 1 - 3))
Over 76dB (AUX 1 - 3)
Over 90dB (TEL)
Over 96dB (EMERGENCY) |
| Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal
EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
| Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
| Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
| Priority |
EMERGENCY: Overrides other inputs
TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting
MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
| Operating Temperature |
-10ºC - +40ºC |
| Finish |
Panel: ABS resin, black, hair line
Case: Steel plate, black |
| Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
| Weight |
12.6kg |
| Accessory |
Power cord x 1,
Terminal block cover x 1,
Terminal block cover mounting screw x 2 |
| Option |
Rack mounting bracket: MB-25B,
Volume control cover: YA-920,
Input transformer: IT-453A |
| Note* |
(*1) 0dB = 1V
(*2) Can be transformer-balanced with the addition of optional IT-453A input transformer.
(*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.)
(*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
| Specification |
|
|---|
| Power Source | 220 - 240V AC or 24V DC | | Rated Output | 30W | | Power Consumption | 34W (EN60065), 78W(AC operation at rated output, 2A (DC operation at rated output) | | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | | Distortion | Under 1% at 1kHz,1/3 rated power | | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:330W (100V)
LOW IMPEDANCE: 4Ω (11V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | | Phnatom Powe | DC + 21V (MIC 1) | | S/N Ratio | Over 60dB | | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | | Indicator | Power signal, peak | | Finish | Panel: ABS resin, black/Case: Steel plate, black | | Dimensions | 420 (W) x 100.9 (H) x 280.2 (D) mm | | Weight | 5kg |
|
P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input. |
Reviews
There are no reviews yet.