Stereo compressor/expander/limiter/gate for complete dynamics management Minimized signal path for optimal sound quality Intelligent Knee for musical performance with soft and hard-knee envelopes Intelligent Ratio adjusts expansion based on input signal Intelligent Gain auto-adjusts output Adjustable attack and release time for manual control Couple switch for a one-touch selection between two mono channels and stereo-linked […]
Stereo compressor/expander/limiter/gate for complete dynamics management Minimized signal path for optimal sound quality Intelligent Knee for musical performance with soft and hard-knee envelopes Intelligent Ratio adjusts expansion based on input signal Intelligent Gain auto-adjusts output Adjustable attack and release time for manual control Couple switch for a one-touch selection between two mono channels and stereo-linked operation Sidechain send and return for use in an external effects loop Switchable low-cut filter minimizes audio-program pumping triggered by kick drum Gain-reduction LEDs and switchable input/output-level LED meters for visual monitoring of critical values Bypass switches on both channels Includes:
3632 Compressor Power cable Quick start guide
Weight
3.10 kg
Reviews
There are no reviews yet.
Be the first to review “ALESIS 3632 Compressor Dual Channel Compressor / Limiter / Gate” Cancel reply
Stereo compressor/expander/limiter/gate for complete dynamics management Minimized signal path for optimal sound quality Intelligent Knee for musical performance with soft and hard-knee envelopes Intelligent Ratio adjusts expansion based on input signal Intelligent Gain auto-adjusts output Adjustable attack and release time for manual control Couple switch for a one-touch selection between two mono channels and stereo-linked operation Sidechain send and return for use in an external effects loop Switchable low-cut filter minimizes audio-program pumping triggered by kick drum Gain-reduction LEDs and switchable input/output-level LED meters for visual monitoring of critical values Bypass switches on both channels Includes:
3632 Compressor Power cable Quick start guide
Outputs: 2x XLR, 2x 1/4" TRS, 2x 1/4" TS Send Maximum Input Level: +21dBu Compression Threshold: -40dB to +20dB Compression Ratio: 1:1 – Infinity:1 Attack Time: 0.1 mSec to 150 mSec/20dB Release Time: 0.05 mSec to 5 Sec/20dB Gate Threshold: Off to +15dB Gate Ratio: 1:1.2 to 1:8 Maximum Output Level: +21dBu Make-up Gain: -20dB to +20dB Frequency Response: 20Hz to 20kHz, +0/-0.05dB Dynamic Range: 125dB Noise: THD+N: 0.01% typical, 1kHz @ +4dBu Power Requirements: 95~120VAC/210~240VAC, 50/60Hz Dimensions (WxDxH): 19 x 7.7 x 1.75" (483 x 195 x 45mm) Weight: 6.8 lbs (3.1kg)
Innovation
The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter designed for use in any professional audio dynamics control application. Multiple Modes The Afterburner can be set up and used in three different ways: In Two channel mode, it performs as two independent compressor/limiters, with 'industry standard' variable Threshold, Ratio and Output gain. In stereo mode, our New Adaptive Stereo Link circuitry provides increased stereo imaging accuracy when linking both channels as a stereo pair. A single front panel switch puts the Afterburner into its alternative Mono mode, setting it up as a Single channel, Dual Band compressor/limiter, with separate dynamics control of both Low and High frequencies, opening up a whole new range of gain control techniques. Enhance Switch In any mode, the Afterburner features an 'Enhance' switch, which provides frequency restoration to preserve the spectral balance of the audio signal, compensating for the sagging Low and High frequency response of compressed program material. Think of it as a 'smart' loudness control.
Features Switchable Modes - Stereo; Dual Channel Single band; or Single Channel Dual Band (Low and High) Low and High frequency compression in Single Channel mode 'Enhance' switch restores spectral balance of compressed signal New Hard/Soft knee compression switch New Adaptive Stereo Link circuit for accurate stereo imaging New Above/Below Threshold LEDs enable at-a-glance compression confirmation Balanced XLR and Jack Inputs and Outputs Sidechain Insert points Intuitive user-friendly layout Flawless performance
New Above/Below Threshold LEDs enable at-a-glance compression confirmation New Hard or Soft knee compression option New LED metering provides accurate Level status, with separate Gain Reduction metering in easy to read 'wide scale' meters. There is also comprehensive LED indication of all operating functions and status in any mode. Balanced Inputs and Outputs On the rear panel, each channel has true differential Balanced inputs and outputs, on both XLR and TRS jack connectors. As well, each channel has a TRS jack Sidechain access insert point, for applications such as De-essing (when used with an external equalizer such as the ARX Multi Q or EQ 260).Other features include a true Hardwire bypass switch for each channel, and passive RFI filters on the inputs. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to the unit via a removable power lead and standard 3 pin IEC connector, with built-in fuse and voltage change switch. With its smooth compression, intuitive user friendly layout, high density precision circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner is equally at home in Studio, Installation, Broadcast and Sound Reinforcement environments. It can provide great sounding dynamics control effects that are not available with any other device.
T E C H N I C A L S P E C I F I C A T I O N S Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 22 dB CMRR >60 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 22 dB Frequency Response 20Hz to 20KHz ±0.2dB Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted Distortion .02% THD @ 0dB,1KHz Dynamic Range 115 dB Sidechain Insert Impedance 10 Kohm Filter Section Filter Type Phase corrected 6dB/octave Summed Filter Response ±0.2dB through crossover region Dividing Frequency 250 Hz Enhance Section Low Enhance 50 Hz, High Enhance 10 KHz Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm Input/OutputConnector type XLR, Balanced Jack Sidechain Insert Connector TRS Jack
Front Panel Controls Hardwire bypass IN/OUT switch Threshold, Ratio and Output Gain controls Above/Below Threshold LEDs 12 segment LED Output Level display Numbered marker panel for labelling compressor assigns 7 segment LED Gain Reduction display Enhance switch and status LED Adaptive Stereo link switch and status LED Dual/Single channel mode switch and status LEDs Rear Panel Connectors Balanced Inputs and Outputs, on both XLR and TRS jack connectors. In Single channel (Mono) mode, use Channel 1 Inputs and Outputs only Sidechain Insert TRS connector on each channel AC input connector, with voltage switch and fuse.
Features
Unique High Density design puts SIX gates in
minimum rack space
Intuitive, 'user friendly' layout
Balanced Inputs and Outputs
Fast, low noise opto-coupler circuitry
Sidechain/Key Input points on each channel
Hardwire Bypass switch on each gate
Flawless performance in any audio environment
The sheer amount of effects and signal processors required for today's
standards of audio production puts a great strain on the available space
in equipment racks, both in the studio and on the road.
So, in order to give engineers more control in less space, we've created
the ARX Sixgate; Six full function noise gates neatly housed in a compact,
all steel 1 RU package, without sacrificing features or quality.
Why Six gates?
Research shows that the majority of noise gates get used on drum kits,
which means using typically 5 to 6 gate channels. Compare this to the
two or maybe 4 channels that most other units have, and you'll see the
reason for the Sixgate's success.And, by using a minimalist approach to
drum gates, the ARX Sixgate has enough gates left over for backing vocals
and other instruments.
Industry Standard controls
Front panel controls for each gate consist of the 'Industry Standard' controls
for Release, Depth and Threshold, plus Red and Green LED displays to indicate
Gate Open or Closed status, and an IN/OUT hardwire bypass switch.
In addition to this, each gate has a blank panel to write on for easy confirmation
of gate assigns. No more pieces of masking tape stuck everywhere!
Ultra Low Noise
Internally, each gate has proprietary ARX ultra low noise high-speed opto-coupler
circuitry with program dependent Attack time, which tracks the incoming signal to
automatically determine optimum gate response.
Balanced Inputs and Outputs
The rear panel features true differential Balanced Inputs and Outputs for each gate,
on insulated TRS jack connectors.Each gate channel also has Individual Key Inputs/
Sidechain access insert points which can be used either for gate control by an external
signal, or for frequency sensitive gating (when used in conjuction with an external
equalizer such as the ARX EQ260).
Universal AC Power
AC power range on the Sixgate is a universal 100 to 120V or 220 to 240V, and is
connected to the unit via a standard 3 pin IEC connector, with built-in fuse and voltage
switch.
The Sixgate's unique combination of High Density design, intuitive 'user friendly' controls,
and clean uncluttered layout make it a truly useful audio tool for all applications.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance
Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise Ratio
Gate Closed: -95 dB Unweighted, -105 dB 'A' weighted
Gate Open, Depth Minimum: -93.5 dB Unweighted -98dB
'A' weighted
Distortion 0 .01% THD @ 0dB,1KHz
Dynamic Range 125 dB
Attack Time Program dependent using high-speed
opto-couplers
Release Time User variable
Input and Output Connector type Balanced Jack
Sidechain Insert Connector TipRingSleeve Jack
Sidechain Insert Impedance 10 Kohm
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“Wide x 13/4“High x 6“Deep; 482 x 44 x 155mm
Front Panel Controls
Individual Release, Depth and Threshold controls
Hardwire bypass IN/OUT switch
Open/Closed gate status LED
Marker panel for labelling gate assigns
Rear Panel
Balanced Inputs and Outputs, on Balanced jack
connectors
Sidechain Insert/Key Input TipRingSleeve jack on
each channel
AC input connector, with voltage switch and fuse
Shure DP11EQE Dynamics Processor Specification:
GENERAL:
Frequency Response: 20 to 20k Hz +/- 1.0 dB re 1 kHz
Dynamic Range: 104 dB minimum, A-weighted, 20 Hz to 20 kHz
Sampling Rate: 48 kHz
Digital-to-Analog, Analog-to-Digital Conversion: 20 bit resolution
Voltage Gain:
1 dB +/- 1dB (power off)
12 dB +/- 2 dB (input 10 dBV, output +4 dBu)
12 dB +/- 2 dB (input +4 dBu, output 10 dBv)
0 dB +/- 2 dB (equal input and output sensitivities)
Impedance:
Input: 47 kilohms +/- 20% actual
Output: 120 ohms +/- 20% actual
Input Clipping Level
+18 dBu minimum (at +4 dBu setting)
+6 dBV minimum (at 10 dBV setting)
Output Clipping Level
+18 dBu minimum (at +4 dBu setting)
+6 dBV minimum (at 10 dBV setting)
Total Harmonic Distortion
LED Signal Indicators
Signal: 40 dB
Clip: 6 dB down from input clipping
Propagation Delay from Input to Ouput
0.8 ms (all filters flat, no dynamics processing, 0 ms delay), up to 2.1 ms (all processing enabled)
Polarity
Input to output: inverting optional (default: non-inverting)
XLR: pin 2 positive with respect to pin 3
1/4-inch TRS: tip positive with respect to ring
Operating Voltage
DP11EQ: 120 Vac, 50/60 Hz, 50 mA max
DP11EQE: 230 Vac, 50/60 Hz, 25 mA max
DP11EQJ: 100 Vac, 50/60 Hz, 50 mA max
Temperature Range
Operating: 0 degrees to 60 degrees C (32 degrees to 140 degrees F)
Fuse
DP11EQ: 120 Vac. Fuse: 100 mA, 250V time delay
DP11EQE: 230 Vac. Fuse: 50 mA, 250 V time delay
DP11EQJ: 100 Vac. Fuse: 100 mA, 250 V time delay
Dimensions
219 mm x 137 mm x 44 mm (8-5/8 in x 5-3/8 in x 1-3/4 in)
Weight: 930 g (2.05 lbs)
DYNAMICS PROCESSOR
Gate and Expander:
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 1.0 to 200 ms
Decay: 0.05 to 1 second
Gate Hold Time: 0 to 0.5 seconds
AGC Leveler
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 0.2 to 3 seconds
Decay: 0.5 to 5 seconds
Hinge: Threshold to 1 dB, 0.5 dB resolution
Compressor and Limiter
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 1.0 to 200 ms
Decay: 0.05 to 1 second
Knee: Hard or Soft selectable
No Overshoot Peak Limiter
Propagation delay: 1 ms
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 0 msDecay: 100 ms
PARAMETRIC EQUALIZER
Parametric Filter Frequency Bands
Up to 9 bands, variable frequency, variable Q
Boost/Cut Range
+6 dB to 18 dB per band
Q Range
1/40-octave to 2 octave
High and Low Shelf/Cut Filters
Shelf, +6 to 18 dB per filter
Cut, 12 dB per octave nominal
DELAY
Up to 1.3 seconds, 21 microsecond resolution
Interactive Reference-Class 2-Channel Expander/Gate/Compressor/ Peak Limiter with
Integrated De-Esser, Dynamic Enhancer, Tube Simulation and Low Contour Filter
Whether you?re recording, mixing or mastering, the COMPOSER PRO-XL MDX2600
gives you total dynamic control. It includes all of the features you would expect from
a reference class compressor?plus a voice-adaptive de-esser, a new dynamic
enhancer, authentic tube emulation and much more. These are some of the indispensable
tools for producing clean, consistent audio with virtually no loss in signal quality.
Features:
Switchable IKA (Interactive Knee Adaptation) program-adaptive compression circuitry
combines the advantages of hard-knee and soft-knee characteristics
Integrated de-esser with switchable male/female voice recognition removes excessive
sibilance from your vocal tracks
IGC (Interactive Gain Control) peak limiting circuitry combines clipper and program
limiter for reliable and inaudible protection against signal peaks
Switchable dynamic enhancer for brilliant, lively audio even with heavy compression
IRC (Interactive Ratio Control) expander/gate circuitry for virtually inaudible
noise suppression
Switchable tube simulation for the extra warmth and transparency of classic
tube circuitry
Automatically or manually adjustable attack and release times
Switchable low contour filter prevents "pumping" due to low-frequency
dominated compression
Stereo couple function with independent output level settings
Switchable side chain input with side chain monitor function
Ultra low-noise 4580 operational amplifiers and state-of-the-art THAT¬ VCA's
Separate 12-segment LED meters for input/output levels and gain reduction
Dedicated "traffic light" threshold and de-esser level displays
High-quality detented ALPS¬ potentiometers and illuminated switches
Servo-balanced inputs and outputs with ? in. TRS and gold-plated XLR
connectors
Relay-controlled hard bypass switch with auto bypass function in case
of power failure
Manufactured under ISO9000 certified management system
Features Four Independent Compressor Channels Channels 1 and 2, 3 and 4 are stereo linkable 7 LED Gain Reduction metering Balanced XLR Inputs and Outputs Sidechain Insert points Intuitive, user friendly layout Flawless performance
The sheer amount of effects and signal processors necessary for today's standards of audio production puts a great strain on the available space in equipment racks, both in the studio and on the road.So, ARX would like to introduce the ARX Quadcomp. An all-new upgrade of the classic award-winning ARX Quadcomp?, the very first four channel 1 RU compressor.You?ll notice that we haven?t strayed very far from our original design concept. The Quadcomp is still four variable ratio Compressor/ Limiters neatly housed in a compact all steel 1 RU package. However, all new low noise/low distortion circuitry, better metering plus XLR inputs and outputs put the Quadcomp in a class of its own. More Control, Less Space On the front panel, each channel has the 'industry standard' individual controls for Threshold, Compression Ratio and Output, plus a new 7 LED Gain Reduction display for accurate visual indication of the amount of gain reduction being applied to the program, and an IN/OUT hardwire bypass switch.In addition to this, each channel has a blank numbered panel to write on for easy confirmation of compressor assigns. Precision Circuitry Internally, each compressor uses Class A VCAs and true 2 pole averaging RMS/DC converters for low distortion and accuracy, plus program dependent attack and release time, which automatically determines optimum compressor response. Balanced Inputs and Outputs The rear panel has true differential Balanced XLR Inputs and Outputs for each compressor. Each compressor has a TRS jack Sidechain access insert point, for frequency sensitive compression, De-essing, etc. in conjunction with an external equalizer (such as the ARX EQ260). Compressor pairs 1 and 2, 3 and 4 also have rear panel mounted Stereo Link switches for accurate stereo tracking. When switched IN, the first channel becomes the master and controls all the functions of the second except Output gain. Universal AC Power AC power range is switchable 100 to 120V, or 220 to 240V, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage switch. Whatever the application ? Channel insert, Bus insert, Master Outputs, Monitor outputs, Crossover outputs, the Quadcomp II?s unique High Density design, precision Low Noise circuitry and clean uncluttered layout make it a truly useful audio tool for all applications.
T E C H N I C A L S P E C I F I C A T I O N S Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 20dB CMRR >50dB, 20 Hz?20 KHz Output Impedance Balanced 300 ohms Unbalanced 150 ohms Output Level (Max) + 20 dB Frequency Response 20Hz-20KHz ±0.5dB Signal to Noise ratio -93 dB Unweighted, -98 dB ?A? weighted Distortion .015% THD @ 0dB,1KHz Dynamic Range 108 dB Attack and Release Times Program dependent Metering 7 LED display: ?1, 2, 3, 6, 12, 18, ?24 dB Sidechain Insert Impedance 10 Kohm Power Requirements 100/120 V AC or 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm Input Connector type Balanced XLR Output Connector type Balanced XLR Sidechain Insert Connector TRS Jack
Front Panel Controls Hardwire bypass IN/OUT switch Threshold, Ratio and Output Gain controls 7 LED Gain Reduction display Marker panel for labelling compressor assigns Stereo link status LEDs Rear Panel Connectors Input and Output balanced XLR connectors TipRingSleeve Sidechain insert connectors Channels 1 and 2, 3 and 4 Stereo link switches IEC AC mains connector with inbuilt fuse and voltage change
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.