| Content |
Recent developments in sound measurement techniques have revealed the limitations
of existing graphic equalisers. The wealth of data that such equipment can provide for
the users requirements - feedback suppression, increased headroom, room equalisation/
compensation can no longer be adequately provided for with a simple graphic equaliser.
The Apex PE MKII is the solution, providing a tool which both enables maximum correction
whilst shaping the response to your specific requirements, combining a full graphic equaliser
with a complementary parametric equaliser/notch filter.
FEATURES:
Electronically balanced input with a balanced floating output stage.
All potential overload points are continuously monitored by an extremely fast "peak-peak"
overload detecter circuit, followed by a "peak-stretching" circuit for clear indication of overload
conditions.Reliablilty is the hallmark of any product, and the mechanical integrity of the components
housing is the vital prerequisite. Sophistical CAD programmes and advanced engineering concepts
have been applied to the chassis design to eliminate the stress and torsional movements which can
damage the electronics.Special attention has been given to the purity of the signal path.The musicality
of previous designs of Apex equalisers has been well appreciated by users, and the PE continues this
tradition, noise and distortion are significantly better than 16-bit digital.Fine-tuning your system is essential.
The "vernier control" provides adjustment refinement on an unprecedented scale.In the event of power failure
to the unit, a failsafe relay links the input to the output ensuring that signal continuity is maintained.
SPECIFICATIONS:
Input
Electronically balanced
Absolute overload point +22dBm
Impedance 10 kOhm (each leg), equal impedance for ?+? and ??? legs
CMRR Better than 65dB (20Hz-20kHz)
connectors XLR-3 type ( pin 1: signal ground, pin 2: hot ?+?, pin 3: cold ?-? )
Output
Electronically balanced and floating, simulating transformer output with app.
10kHom to ground impedance for each leg
Max level +21dBm into 600 Ohms
Impedance 51 Ohms (each leg)
Symmetry balance Better than 65dB (20Hz-20kHz IEC)
connectors XLR-3 type ( pin 1: signal ground, pin 2: hot ?+?, pin 3: cold ?-? )
Performance
Frequency response +0 ?0.5 dB, 40Hz-20kHz (graphic EQ in)
THD < 0.01%, 20Hz-20kHz
Noise < -94 dBm (typ. -98dBm), graphic and parametric equalisers in circuit (0dB settings)
Measurements: , 22Hz-22kHz RMS unweighted
Level Control -? to +6dB
Level control ?0dB? cal. accuracy +- 0.2 dB (overall gain input to output)
Overload indicator
Lights for approximately 200ms if the instantaneous peak voltage at any point in
the equaliser comes within 2dB of clipping
Filters
Graphic equaliser:
30 ISO center frequencies
25Hz to 20kHz 1/3 octave
Center frequency tolerance +-1% (typically better than +-0.5%)
Q tolerance+-1%
Max boost/cut 6 or 12dB +-0.5dB reciprocal
switchable
Parametric filters:
Tuning ranges 18-200Hz, 180Hz-2kHz, 1800Hz-20kHz
Vernier control+- 10% of main frequency control
Range of Q adjustment 0.5 to 8
Range of level adjustment
-? to +15dB (typ -45 to +15.5dB) non reciprocal. Smaller cut than boost curves
through addition and substraction of parametric bandpass filter output to filter input
Each filter individually switchable
High pass filter:
Frequency range 15-300Hz (-3dB frequencies)
Type
Maximally flat 12dB/oct
Switchable
Power Requirements
Voltage 110/120/220/240V 50/60Hz
Consumption 30VA
Connector IEC type
Size and weight
dimensions 482 x 133 x 255 mm (19 x 5.2 x 10 inch)
weight 7 kg
| Digital stereo active crossover with 4 inputs and 8 outputs, incl. software .
- Flexible routing configurations for all standard mono and stereo output operating modes
- 4 analog inputs and 8 analog outputs (XLR)
- Active frequency filter types (Bessel, Butterworth and Linkwitz-Riley) with slopes up to 24 dB/octave split up the audio signal into different frequency bands
- Incl. software editor (for PC and Mac) for remote control via computer through USB interface: store, transfer, and manage your presets
- Up to 30 user presets storable in the device via software
- 5 menu languages selectable (German, English, French, Spanish, Dutch)
- Alphanumeric LCD screen with 2 lines of 16 characters each
- Input sensitivity digitally adjustable
- Inputs and outputs with 4-digit LED level meter as well as clip and limit LED indicator
- Mute switch with LED indicator per output
- 7-band parametric EQ per output
- Up to 7 ms signal delay adjustable for the outputs
- Output limiter with adjustable limits and automatic attack and release settings as overload protection for your amplifying system
- Switchable phase
- Lock function for prevents undesired changes to settings
- Rack installation, 1 U
- Windows XP, Vista, 7, 10 and Mac OS X 10.5.8 and better
- Digital signal processor
- The device can be connected via USB to the PC in connection with DXO Software
The firmware can be updated via the PC connection
- (19") 48.3 cm rack installation 1 U
| Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
| Power connection: |
Mains input via Coaxial power connector (M) power supply cord with AC adapter (provided) |
| Frequency range: |
10 - 22000 Hz |
| THD: |
<0,005 % at 1 kHz |
| DSP: |
Digital signal processor |
| Crossover frequency: |
20-20000 Hz |
| Impedance: |
Input 10 kOhm
Output 50 Ohm |
| Gain: |
Output: -50 dB to +12 dB |
| Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
| Delay: |
0 - 7 ms |
| Dynamic range: |
Input: 114 dB
Output: 110 dB |
| Sample rate: |
48 kHz |
| Connections: |
Input: line via 4 x 3-pin XLR
Output: line via 8 x 3-pin XLR |
| Max. level: |
Input: +22 dBu
Output: +9 dBu |
| USB port: |
Typ B |
| PC connect: |
DXO Software via USB, firmware can be updated |
| Housing design: |
(19") 48.3 cm rack installation 1 U |
| Dimensions: |
Width: 48,3 cm
Depth: 22,3 cm
Height: 4,45 cm |
| Weight: |
1,90 kg |
|
DBX 2215 Dual 15-Band Graphic Equalizer with Noise Reduction
It's amazing. One little button. So much effect. dbx? Type III? Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one's surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see.
But hey, Roger wasn't about to stop there. PeakPlus? Limiter. Who knows more about limiting than the folks at dbx; nobody... that's who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in." Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.
20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You'll see, with the 20 Series EQs you get MORE!!!
SPECIFICATIONS:
|
INPUT
| |
Connectors:
|
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
| |
Type:
|
Electronically balanced/unbalanced, RF filtered
| |
Impedance:
|
Balanced 40k ohm, unbalanced 20k ohm
| |
Max Input Level:
|
>+21dBu balanced or unbalanced
| |
CMRR:
|
>40dB, typically >55dB at 1kHz
| |
OUTPUTS
| |
Connectors:
|
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
| |
Type:
|
Impedance-balanaced/unbalanced, RF filtered
| |
Impedance:
|
Balanced 200 ohm, unbalanced 100 ohm
| |
Max Output Level:
|
>+21dBu balanced/unbalanced into 2k or greater
>+18dBm balanced/unbalanced (into 600)
| |
SYSTEM PERFORMANCE
| |
Bandwidth:
|
20Hz to 20kHz, +/-0.5dB
| |
Frequency Response:
|
50kHz, +0.5/-3dB
| |
Noise Reduction In:
|
(+/-6 and +/-15dB range):
| |
Signal-to-Noise:
|
>102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
| |
Dynamic Range:
|
>120dB, unweighted
| |
Noise Reduction Out:
|
(+/-6dB range):
| |
Signal-to-Noise:
|
>94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
| |
Dynamic Range:
|
>112dB, unweighted
| |
Noise Reduction Out:
|
(+/-15dB range):
| |
Signal-to-Noise:
|
>90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
| |
Dynamic Range:
|
>108dB, unweighted
| |
THD + Noise:
|
| | High-Definition 31-Band Stereo Graphic Equalizer with FBQ Feedback Detection System
- Professional 31-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated mono subwoofer output with adjustable crossover frequency
- Additional sweepable high and low-cut filters for each channel remove unwanted frequencies, e.g. floor rumble, hiss etc.
- Highly accurate 12-segment LED input/output metering and input gain controls for easy level setting
- Relay-controlled hard-bypass with an auto-bypass function during power failure (fail-safe relay)
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
- 3-Year Warranty Program*
- Conceived and designed by BEHRINGER Germany
| PRICE WITHOUT V.A.T.
BSS Opal FCS-966 Constant Q Graphic Eq
Graphic equalisers are found in just about every sound application, from room contouring to feedback control and general audio sweetening.
Traditionally, much general eq'ing takes place on the faders alone, but this restricts the use of the faders at each end of the scale for further precision eq work. So we provided the Opal FCS-966 with separate LF and HF contour filters which can change an overall sound balance without disturbing a detailed room or loudspeaker response.
These filters are very musical gentle boost and cut shelving filters which can be used to add (or remove) room effects that change with temperature, audience numbers or humidity.
All these effects can be easily made without disturbing the critical fader settings already made.
Constant Q Filters
The modern generation of graphic eq's
uses the Constant Q topology, pioneered by BSS Audio, which means that the filter width is constant whatever the fader gain setting.
Compared to the earlier 'gyrator' style of filters, Constant Q filters provide a smoother and more predictable interaction between adjacent faders and the resulting eq curve more closely resembles the actual fader positions.
More Gain Control Per Filter
Each eq fader has +/-15dB of adjustable gain, more than many competitive graphic eq's. The faders are long-throw 45mm types for precision control.
High Pass Filter
Also provided on the FCS-966 is a sweepable high-pass filter which can be used very effectively to restrict the low-energy output for better amplifier and loudspeaker performance. Stage monitors also benefit from the application of a high-pass filter to remove bass signals e.g. from vocal-only wedges.
Metering
BSS Audio believes in providing engineers with information, and the FCS-966's 8-segment led meter shows output level and warns of signal clipping within the eq. When the unit is switched to bypass, the meter will read the input level, allowing accurate matching of the 'dry' and equalised signals using the gain control.
Centre Bypass
When any eq fader is in its centre detent position, the filter is automatically bypassed, for optimum performance.
Input/Outputs
All the inputs and outputs of the FCS-966 are electronically balanced, with optional transformer balancing. To make installation of the FCS-966 easier, we've provided three differerent interface connectors: XLR-type, 1/4" TRS jack and Phoenix/Combicon screw terminals.
Relay Bypass
The EQ IN buttons switch the EQ path
into circuit. When switched out, or power fails, a high-quality relay switches the input signal directly to the output connectors.
Control Descriptions
Faders
30 EQ filter faders on ISO centres, each with nominal +/-15dB of gain. Positive centre-detent on 45mm long-throw precision faders.
HP Filter
Sweepable high pass filter, frequency adjustable from OUT (flat) up to 250Hz.
LF Contour
Smooth shelving filter, +/-6dB of gain at 50Hz
HF Contour
Smooth shelving filter, +/-6dB of gain at 14kHz.
GAIN
Used for overall unity gain adjustment. Adjustable from - infinity to +10dB.
CLIP
Triple-point clip detector that indicates red when the internal signal is clipping at any one of three critical points.
LED Meter
Shows output signal level (input signal when eq is bypassed) from -24dBu to +18dBu in 8 steps. |
The class-A circuit used in the EQ-73 is similar to the eq section in the classical 1073 module, without the high pass filter. Additional frequencies have been added and the mid frequency band uses two inductors, the higher value of the second one is used for the two lowest frequencies, 160 Hz and 240 Hz, to achieve a suitable response.
The sound character is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
The EQ-73 has stepped frequency controls that offers a wide selection of frequencies from 20 Hz to 24 kHz.
The Low and High frequency bands are shelving and the mid frequency band is of the bell type.
The control range is +/-15 dB for the two lower bands and +/- 18dB for the high frequency band.
There are separate bypass switches for all three bands.
The EQ-73 is made to be used together with one of our PRE-73 models that has an Insert jack. It can also be used with many other units that has a low level insert jack.
Combining a PRE-73 and an EQ-73, and using a UNITE rack kit to mount them together, one will get a 19-inch 1073-style unit at a low cost and with a great sound!
FEATURES
- Vintage Style electronics. No intergrated circuits in the signal path
- 3-band with a dual inductor based mid frequency band
- Stepped frequency selection
- A wide selection of frequencies from 20 Hz to 24 kHz
- Control range up to +/- 18 dB
- Separate Bypass switches for each band
- Tantalum capacitors in the signal path
- Made to be used together with one of our PRE-73 models with an Insert jack or any other unit with a low level Insert jack
- TRS jack for in-and output connection, the nominal working level is around 18 dBu
- Selectable ground lift switch
- External power supply to avoid interaction with the audio circuits
- Great sound that suits most sound sources and genres
- A solid build quality that will last many years of normal use
|
Reviews
There are no reviews yet.