Content |
The Model 207D is an affordable, audiophile quality tube mic preamp that meets or exceeds the performance of preamps costing many times more. The Model 207D will reveal the subtlety and power of vintage condensers, ribbons, electrets, and popular dynamic mics. Even the world's most respected microphones will sound better. Plus, with its AES/EBU and S/PDIF digital outputs and Word Clock connection, the Model 207D offers direct digital connection throughout your signal chain, with up to 96kHz sampling rates. The instrument inputs also are quieter and have more gain, than conventional instrument preamps. The MicLimT circuitry, previously only available in our flagship Model 1100 2 channel and Model 1788 8 channel mic preamps, makes the Model 207D virtually crashproof - making it a perfect front end for digital recorders. By combining the best traits of tube and solid state circuitry, the Model 207D captures a sound that is warmer, fuller and more true to life. Whether you are recording, mixing live, broadcasting or webcasting, the signal has to travel a long journey before its final delivery. So give your sound a great start with the Aphex Model 207D Tube Mic/Instrument Preamp with Digital Outputs.
BENEFITS: Dramatically improves microphone performance Greater dynamic range and frequency response Dramatically improves instrument performance Fuller, more realistic sound Improved Detail and Intelligibility Record hotter tracks with the highest possible resolution Tighter lows; clearer up-front mids; Strong highs without edginess MicLim? offers up to a 20dB increase in dynamic range and makes the Model 207D virtually crashproof Direct connection to digital mixers, DAW's and other digital equipment FEATURES: Two independent low noise channels of tube amplification AES/EBU and S/PDIF digital outputs with up to 96k sampling rates Microphone and Instrument inputs on each channel MicLim? on each channel Mic Input: 20 to 65dB of continuously variable gain Instrument Input: -infinity to 65dB of continuously variable gain Switchable 48 volt Phantom Power with ramp up feature Delayed Turn On Polarity, 20 dB pad and Low Cut Filter switches LED Headroom Meter Display for each channel Switchable -10 dBv / +4 dBu operating level Balanced 3-pin and 1/4" TRS Inputs and Outputs Internal Switch Mode Power Supply |
The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.
The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.
The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.
The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.
The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.
The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
- LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme. |
Having had great success with the PRE-73 preamp, we have received many requests for a version for the 500 eries rack format. We are therefore happy to present the PRE-573, expected to start shipping in late September.
The PRE-573 is a one width module that has the sound and the features that made the PRE-73 so successful and a few additional ones.
The circuit still uses the preamp and output section from the classic 1073-module, adapted to work in the api rack format. It has a total gain range from -15 to +80 dB. The 10 - 70 dB range is handled by a turn switch and there is a separate toggle switch to select an additional 5 or 10 dB gain. The input can be configured to accept line level signals by another switch, the gain is then lowered by about 25 dB and the input impedance increased to about 15 kohm.
The input impedance of the mic input mode can be switched between 1200 and 300 ohm. Phantom power and phase reverse is also selectable by front panel switches.
An added feature, using the same circuit as in the PRE-73 DLX, is the active DI-input with a high input impedance of about 1,5 Mohm. The output signal from the active DI circuit passes through the input transformer for some extra character.
The DI-input is very flexible since it can be changed to a purely passive one by a front panel switch. The DI input is then exactly the same as in the PRE-73 Mk2 where the signal is feed directly into the second gain stage, bypassing the transformer and with an input impedance of about 100 kohm.
These two DI-options makes it possible to get different tones from electric instruments and the passive DI input mode is more suited for injecting active units like sound modules.
A new feature is the switchable AIR mode that adds a small boost above 10 kHz that peaks at 2 dB at about 35 kHz.
A simple but effective signal and overload indicator is offered by a single LED that starts glowing red at about +4 dBu and then increases its intensity up to the maximum output level.
The PRE-573 has a dedicated insert connector at the back allowing it to interface with other GAP 500 modules. The insert can be activated by removing a jumper connector at the back of the module.
The second Golden Age Project module for the api 500 rack will be the EQ-573, expected to ship in November 2012. The EQ-573 consists of the inductor based high pass filter section and the 3-band eq section from the classic 1073 module with some added frequencies. These two modules together will offer a fully fledged 1073-module in a compact format at a very low cost.
There is a second jumper at the back of the module that selects 600 ohm termination on the output. The standard mode is termination on, since it gives the flattest response when the PRE-573 is used with modern line inputs that typically has an input impedance of 10 kohm or more. The user can chose to remove the jumper and deactivate the termination resistor, this will increase the level above 10 kHz and create a peak in the response for an even more pronounced "Air" effect.
The output is transformer balanced and fully floating and can drive a 600 ohm load up to level of about 28 dBu.
|
- 1 microphone, XLR (bal.) or 6.3 mm jack (unbal.)
- Gain control, 10 steps (6-50 dB)
- Phantom power can be switched on
- Clip LED
- 1 line output, XLR (bal.) or 6.3 mm (unbal.)
- Operation via supplied power unit
Power supply: | 12 V DC, 150 mA | Input impedance: | 10 kohms bal./unbal. | Max. input level: | +4 dB bal./+10 dB unbal. | Gain: | 50 dB XLR/44 dB jack | T.H.D.: | 0.01 % | Frequency range: | 25 Hz - 16 kHz | S/N ratio: | >75 dB | Dimensions: | 143 x 93 x 45 mm | Weight: | 350 g |
|
Applications
Console input extending for both Digital and Analog mixing consoles in Studio, Live and Broadcast Mic Pre-amps for ADAT/ Hard Disk/ Multitrack Recording Innovation If you love your compact Digital (or Analog) mixing console, but wish it had more microphone inputs, ARX has the solution ? the 8 Pre: eight channels of superb sounding Microphone Pre-amps in a compact 1 RU chassis. The 8 Pre is the ideal console extender for those times when you need more microphone inputs. Now you can put those unused line inputs to good use, and who knows - the 8 Pre pre-amps sound so good that you?ll probably end up using them all the time instead of the ones that came with your mixer! Superb Audio Quality The 8 Pre?s ultra low noise figures come from extensive use of premium components plus care and attention to board design and layout. The result is superb, transparent audio quality and the headroom to handle anything that a mic can throw at it. Gain is adjustable from 20 db through to 60 dB via a trim control on the front panel, plus we?ve included a ?20dB Pad switch to tame the hottest condenser mic output if required. The Clip status LED lights up 1 dB before the onset of clipping, just to warn you you?re getting close.Phantom power is switchable in banks of four channels: 1 through 4, 5 through 8. A Phase reverse switch is also provided on each pre-amp channel to eliminate any close miking problems. In short, the ARX 8 Pre is the mic Pre-amp that you?ll wish the console manufacturer had used. It provides a unique solution to today?s multiple Mic Pre-amp requirements.
T E C H N I C A L S P E C I F I C A T I O N S Input Gain 20dB to 60dB Input Pad ?20dB Input Impedance 4 KOhm Input Headroom +23dB Output Impedance 300 Ohm Output Level (Max) +23dB Frequency Response 20Hz ? 20KHz ±0.2 dB Signal to Noise ratio (Gain set @ 20 dB) ?93dB Unweighted, ?99dB ?A? weighted Distortion @ Unity Gain .004%, 20 Hz ? 10 KHz Dynamic Range 116 dB Phantom Power 48 VDC Input Connectors Balanced XLR Output Connectors Balanced TRS jack Clip Indicator Illuminates 1 dB prior to clipping Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm |
Mic Inputs
• Frequency response at minimum gain (0dB): -0.35dB at 20Hz and –3dB at 122kHz
• Frequency response at maximum gain (60dB): –2.5dB at 20Hz and –3dB 103kHz
• Gain range: 0dB to +60dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +7.4dBu
• THD+N: 0.0009% (measured at 1kHz -20dBu input signal, at 30dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise EIN: -126dB (measured at 60dB of gain with 150Ω termination and 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -98dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 123dB (relative to max output 25dBu)
• SNR: 120dB (relative to 0dBFS (+22dBu)
• CMRR: 88dB.
• Input Impedance, variable: 600Ω, 1400Ω, 2400Ω, 6800Ω
Line Inputs
• Frequency Response at unity gain (0dB): -0.3dB at 20Hz and –3dB at 94kHz
• Gain range: -20dB to +10dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +25.4dBu
• THD+N: 0.002% (measured with +4dBu input signal, 0dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -91dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 116dB (relative to max output 25dBu)
• SNR: 113dB (relative to 0dBFS +22dBu). Input Impedance: 10kΩ
Instrument Inputs
• Frequency Response at +10dB gain: -0.2dB at 20Hz and 0dB at 200kHz
• Frequency Response at +40dB gain: -3dB at 20Hz and –3dB at 38.4kHz
• Gain range: +10dB to +40dB continuously variable
• Maximum headroom: +11.5dBu
• THD+N: 0.006% (measured with –20dBu input signal, at minimum gain (+10dB), with a 20Hz/22kHz bandpass filter)
• Noise at main output with minimum gain (+10dB): -95dBu (measured with a 20Hz/22kHz bandpass filter)
• Input Impedance = >1MΩ
High Pass Filter
• Roll off = 18dB per octave 3 pole filter
• Frequency range: 16Hz to 420Hz (continuously variable, measured at the 3dB down point)
Meters
• 6 LED meter is calibrated 0dBFS = +22dBu (the maximum level which can be correctly converted by the optional internal A/D converter before overload occurs). The meter calibration points are as follows:
Meter panel calibration value in dBFS / Equivalent dBu value
0dBFS / +22dBu
-2dBFS / +20dBu
-6dBFS / +16dBu
-12dBFS / +10dBu
-18dBFS / +4dBu
-42dBFS / -20dBu
Front and rear connectivity
Analogue Channel Inputs (Inputs 1-4)
• 4 instrument 1⁄4” TS jack inputs on front panel
• 4 microphone XLR inputs on rear panel
• 4 line 1⁄4” TRS jacks on rear panel
• 4 insert return 1⁄4” TRS jacks on rear panel
• 4 ADC XLR inputs on rear panel
Analogue Audio Outputs (Outputs 1-4)
• 4 line XLR outputs on rear panel
• 4 insert send 1⁄4” TRS jacks on rear panel
Other I/O
• IEC power input connector 100Vac – 240Vac
Front Panel Indicators
• 8 output meters, 6 segment
• 4 30-60 mic gain range selection indicator
• 4 +48V phantom power indicator
• 4 Phase indicator
• 4 Insert In indicator
• 4 Filter In indicator
• 4 Input selection indicators (Mic, Line, Inst)
• 4 Z In microphone input impedance selection indicators (Low, ISA110, Med, High) Clock select indicators (44.1, 48, 88.2, 96, 176.4, 192)
• Ext clock indicators (Lock, Word clock, 256X)
Weight
5.5kg
12.2lbs
Dimensions (W x H x D)
480mm (W) x 88mm (H) x 280mm (D)
19" (W) x 3.5" (H) x 11" (D)
|
Reviews
There are no reviews yet.