ART CABLECOP CABLE TESTER

CableCOP - Cable Tester Overview

There are several types of cables used widely in pro audio ? mic cables and
patch cords with 2 or 3 conductors, instrument cables with 2 conductors, basic
speaker cables with 2 conductors and MIDI cables comprised of DIN5 connectors
using 2 conductors.
The CableCOP features a full selection of standard pro audio connectors for testing
all such cables. LEDs on the CableCOP link its various connector terminals and will
only illuminate when the connected ?cable? completes a circuit. As a result you?re
able to tell, at a glance, which cables need to be repaired. Sometimes the problem
can be the cable itself. An LED may also fail to illuminate if a 3-conductor cable
has been wired out-of-phase. As an example, if the Tip of one 1/4? TRS plug on a
(balanced) patch cable were soldered to the same cable conductor as the Ring or
Sleeve of the other 1/4? inch TRS plug.

CableCOP - Cable Tester Specifications:

Power Requirements 9V Battery (included)
Dimensions 3.75x2.5x1.5 inches (90mm x 63mm x 40mm)
Weight 1lb (454g)

ACOUSTILYZER
 
The Acoustilyzer AL1 functionality complements and expands the ML1
Minilyzer with a new and comprehensive set of acoustical measurement
functions.
The optimized combination of electrical and acoustical features creates
the perfect all in one tool for sound/systems contractors, installers and
multi-media specialists. The Acoustilyzer AL1 is available as a palm-sized
portable acoustical analyzer or as firmware for Minilyzer owners with optional
available STI-PA measurement functionality.
Required Accessories:
The AL1 requires a measurement microphone for acquiring acoustical signals.
NTI offers the following microphones:
- MiniSPL, class 2 acc. IEC 61672
- M2010, class 1 frequency response (ext. phantom power supply required)

Product Details  
Sound Pressure Level: Leq, short-time Leq , LE, Lmin, Lmax,
Real Time Analyzer: 1/1 or 1/3 octave band resolution SPL/LEQ display per
band, max - min display
Zoom FFT: Actual level and Leq, full band up to 0.7Hz resolution
Reverberation Time: RT60 with 1/1 octave band resolution, confidence indicator,
according to ISO3382
Delay Time: Propagation delay between electrical and acoustical signal (built in mic),
resolution: 0.1ms
STI-PA (optional): Single value STI or CIS test result, modulation indices display,
individual band level results, error indicator, amplitude weighting acc. IEC 60268-16
release 2003
Electrical: Level RMS, THD+N, Polarity
Measurement microphone: Required for acquiring acoustical signals, NTI offers MiniSPL
or M2010 measurement microphones

• Microprocessor-controlled cable tester featuring 3 modes: cable and installed cable test plus test tone mode
• Accepts all standard connectors: XLR, Speakon*, TRS (1/4“, 1/8“), RCA, RJ45, MIDI and USB
• Super-easy operation with intuitive LED display
• Continuity check and intermittent contact detection

• Phantom-power and ground-shield check
• Test-tone generator: 1 kHz or 440 Hz at +4 dBu, -10 dBV or -50 dBV
• Operates with 2 AA size batteries (not included)
• Designed and engineered in Germany

• Measures impedance of speaker lines up to 100k ohms
• Batteries: four (AA)
• Zero adjustment for accuracy on all ranges
• Easy to read meter calibrates directly in ohms
• Includes carrying case, test leads and impedance to power reference chart
• Five year warranty

This is an on-the-road tool you certainly can't miss in your gearbox! A nifty, handy cabletester, which allows you to check up to six (welding) connections and gives you a visual readout by 2 rows of 6 LED's. The checking itself is done manually per connected pin. A LED will light up to indicate what pin is connected correctly on which side. A short-circuit check with a red LED and audio-warningsignal is also included. On the left and right side you'll find inputs for 6,3 symm. jack, BNC, RCA, 5p. DIN, 5p. XLR, 3p. XLR and Neutrik® Speakon®.