| Content |
HeadAMP - Four Output Stereo Headphone Amp Overview
Most home recordings involve from one to four people, any or all of whom are
going to need headphone monitoring. The monitor amp would be connected
to the tape deck?s headphone output or a mixer output so that the performers
can hear themselves and each other. Of course the same application can apply
to band rehearsals and even home entertainment. HeadAMP provides amplification
and individual volume control for up to 4 headsets. It can be driven by either line-
level or headphone amplifier signals (mono or stereo).
HeadAMP - Four Output Stereo Headphone Amp Specifications:
Signal To Noise Ratio >90dB
IMD (SMPTE) 0.01%
Maximum Input Level +14dBV
Maximum Output Level 20dB per channel
Output Impedance 51 Ohms per channel
Output Connectors Four stereo 1/4? headphone outputs
Power Requirements 12V DC (Adapter included)
Total Harmonic Distortion |
Overview
Sound can be perfected with Sennheiserʼs HDVA 600. Delivering authentic sound in its purest form, listeners are treated to a world of sheer listening pleasure. Years of knowledge in audio engineering and innovations in acoustic amplification, resulted in the creation of the HDVA 600. The consistently symmetrical signal processing and extremely low harmonic distortion guarantees an absolutely precise sound. Also, thanks to their pre-amp performance, they are easy to adjust and be connected directly to speakers for optimum audio amplification. In essence, the HDVA 600 provides a spectacular listening experience when paired with any Sennheiserʼs audiophile headphones.
Features
Consistently symmetrical signal processing for maximum sound quality
Symmetrical inputs and outputs simplify integration into a system
High-end ALPS quadruple potentiometer achieve perfect channel equality
Variable gain factor (five stages) for optimized use of low impedance headphones
Sophisticated metal housing to protect against signal scatter and vibration
Solid controls turned from solid metal, providing the utmost in long-term stability |
Specifications
General
Frequency response
20 Hz - 20 kHz (+0 dB, -1.5 dB)
Signal-to-noise ratio
100 dB (IHF A-weighted, input level control min.)
Channel separation
80 dB between adjacent channels
Line input
Front: 6.3 mm jacks, unbalanced
Rear: RCA connectors, unbalanced
Input impedance
40 kOhm
Nominal level
-10 dBV (0.3 V)
Headphone outputs
four 6.3 mm stereo jacks
Maximum output power
2 x 1.5 W at 8 Ohm (1 channel in use)
2 x 1,2 W an 8 Ohm (four channels in use)
Power supply
230 V AC, 50 Hz
Power consumption
10 W
Dimensions (W x H x D)
482 mm x 44 mm x 196 mm
Weight
4 kg | Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
|
Overview
With Sennheiserʼs HDVD 800, sound is perfect. The HDVD 800 is able to connect with digital sources and is equipped with a high-quality Burr-Brown digital/analog converter (DAC) that converts digital audio data into analog signals with a resolution of 24 bits and a sampling rate of up to 192 kHz. This enables the HDVD 800 to transmit the entire frequency spectrum of high-end audio sources without any loss of frequencies.
In addition to the symmetrical inputs, the HDVD 800 also has an asymmetrical input socket; incoming signals are symmetrized before further processing takes place. Digital sources can be connected to the rear of the unit via an XLR (AES/EBU) input, optical and coaxial (S/PDIF) digital inputs or USB. All digital inputs accept signals up to 24 bit at 192 KHz*. Designed and manufactured in Germany, this high-end, solid-state amplifier harmonize perfectly and deliver an ultimate acoustic performance when paired with any of Sennheiserʼs audiophile headphones.
Features
D/A transducer for all common formats up to 24 bit / 192 kHz
D/A transducer can be used for CD and DVD players
AES/BU, S/PDIF, USB inputs
Symmetrical (XLR) and asymmetrical (RCA) analog inputs
Symmetrical output
Sockets for four sets of headphones (two of which symmetrical)
|
- Ultra-compact monitor headphone amplifier for studio and stage applications
- Personal \'\'more me\'\' mixer – mix a mic plus a monitor signal and hear them via headphones
- Flexible Mic In and Mic Through connectors plus Ground Lift switch
- Stereo Monitor input with dedicated Monitor Level control and Mono/Stereo switch
- High-power headphone output on 1/4\'\' and 1/8\'\' jack connectors
- DC 12 Vadapter included
- 3-Year Warranty Program*
- Designed and engineered in Germany
|
Reviews
There are no reviews yet.