ART MyMONITORII Headphone amplifier

132.00 incl. GR VAT

Available on backorder

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
The MYMonitorII allows blending of any microphone source with any stereo source in a convenient personal monitoring solution. The microphone thru provides direct connection to any mixer and will pass phantom power from the board for powering condenser microphones. Built for maximum flexibility, the ARTcessories MyMonitorII can be powered with the supplied 12vDC power supply, […]

 

Read more

The MYMonitorII allows blending of any microphone source with any stereo source in a convenient personal monitoring solution. The microphone thru provides direct connection to any mixer and will pass phantom power from the board for powering condenser microphones. Built for maximum flexibility, the ARTcessories MyMonitorII can be powered with the supplied 12vDC power supply, or from an internal 9v battery.

The pop-less microphone on/off switch lets you locally mute the microphone. The headphone section has independent 1/8-inch and ¼-inch TRS outputs with plenty of drive for both.

 

  • Blends any Microphone, Instrument and Stereo Source for Personal Monitoring
  • Microphone Input and Thru with Pop-less On/Off Mute Switch
  • Passes Phantom Power for Operation with Condenser Microphones
  • Instrument/Line Input and Thru Jacks
  • Stereo Monitor Input with Blend Control
  • Headphone output section has 1/8-inch and 1/4-inch Jacks
  • High Performance, Low Noise Circuitry
  • 9v battery and 12vDC Power Operation

 

Weight 2.00 kg

Reviews

There are no reviews yet.

Be the first to review “ART MyMONITORII Headphone amplifier”

Your email address will not be published. Required fields are marked *

Quick Comparison

ART MyMONITORII Headphone amplifier removeBEHRINGER MA400 Ultra-Compact Monitor Headphone Amplifier removeTASCAM MH-40MKII HEADPHONES PRE-AMPLIFIER removePALMER PHDA02 Pro PHDA 02 - Reference Class Headphone Amplifier - 1-channel removeLD Systems HPA 1 - Amplifier for headphones and wired IEM In-Ear-Monitoring removeSennheiser HDVA 600 Headphones Amplifier remove
NameART MyMONITORII Headphone amplifier removeBEHRINGER MA400 Ultra-Compact Monitor Headphone Amplifier removeTASCAM MH-40MKII HEADPHONES PRE-AMPLIFIER removePALMER PHDA02 Pro PHDA 02 - Reference Class Headphone Amplifier - 1-channel removeLD Systems HPA 1 - Amplifier for headphones and wired IEM In-Ear-Monitoring removeSennheiser HDVA 600 Headphones Amplifier remove
Image
SKUAT/EM/000034E005310MH-40MKIIPHDA02LDHPA1S07SE00313
Rating
Price 132.00 incl. GR VAT 31.00 incl. GR VAT 565.55 incl. GR VAT 353.91 incl. GR VAT 119.95 incl. GR VAT 1,499.00 incl. GR VAT
Stock

Available on backorder

In stock

In stock

Available on backorder

Only 4 left in stock (can be backordered)

In stock

AvailabilityAvailable on backorderIn stockIn stockAvailable on backorderOnly 4 left in stock (can be backordered)In stock
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

The MYMonitorII allows blending of any microphone source with any stereo source in a convenient personal monitoring solution. The microphone thru provides direct connection to any mixer and will pass phantom power from the board for powering condenser microphones. Built for maximum flexibility, the ARTcessories MyMonitorII can be powered with the supplied 12vDC power supply, or from an internal 9v battery.

The pop-less microphone on/off switch lets you locally mute the microphone. The headphone section has independent 1/8-inch and ¼-inch TRS outputs with plenty of drive for both.

 
  • Blends any Microphone, Instrument and Stereo Source for Personal Monitoring
  • Microphone Input and Thru with Pop-less On/Off Mute Switch
  • Passes Phantom Power for Operation with Condenser Microphones
  • Instrument/Line Input and Thru Jacks
  • Stereo Monitor Input with Blend Control
  • Headphone output section has 1/8-inch and 1/4-inch Jacks
  • High Performance, Low Noise Circuitry
  • 9v battery and 12vDC Power Operation
 
  • Ultra-compact monitor headphone amplifier for studio and stage applications
  • Personal \'\'more me\'\' mixer – mix a mic plus a monitor signal and hear them via headphones
  • Flexible Mic In and Mic Through connectors plus Ground Lift switch
  • Stereo Monitor input with dedicated Monitor Level control and Mono/Stereo switch
  • High-power headphone output on 1/4\'\' and 1/8\'\' jack connectors
  • DC 12 Vadapter included
  • 3-Year Warranty Program*
  • Designed and engineered in Germany

Specifications
General

Frequency response
    

 
    

20 Hz - 20  kHz (+0 dB, -1.5 dB)

Signal-to-noise ratio
    

 
    

100  dB (IHF A-weighted, input level control min.)

Channel separation
    

 
    

80 dB between adjacent channels

Line input
    

 
    

Front: 6.3 mm jacks, unbalanced
Rear: RCA connectors, unbalanced

   Input impedance
    

 
    

40 kOhm

   Nominal level
    

 
    

-10 dBV (0.3 V)

Headphone outputs
    

 
    

four 6.3 mm stereo jacks

   Maximum output power
    

 
    

2 x 1.5 W at 8 Ohm (1 channel in use)
2 x 1,2 W an 8 Ohm (four channels in use)

Power supply
        

230 V AC, 50 Hz

Power consumption
    

 
    

10 W

Dimensions (W x H x D)
        

482  mm x 44  mm x 196  mm

Weight
    

 
    

4 kg

The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.

In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.

The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.

Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.

The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.

 

 

The LD Systems HPA 1 is a versatile headphone amplifier with high power output for stage, studio and home recording and is the perfect solution for wired in-ear-monitoring.. The compact device in a rugged, ergonomically shaped plastic housing with soft-touch surface and practical belt clip is very extensively equipped. In addition to locking XLR connectors for the stereo signal L/R input, the HPA 1 has a balanced 3.5 mm stereo jack as AUX input, which can be used in parallel for clicks or playback. It is protected for safe operation against excessive input levels; a hollow pin socket with negative internal contact enables the connection of a network adapter for fixed operation. A 3.5 mm stereo jack is provided as earphone and headphone output. Volume level and balance can be set with easy-grip knobs, a push-button switches between the summed mono and stereo signals. A full-fledged limiter is integrated for distortion-free playback and as protection against feedback. The LD Systems HPA 1 has bi-colour LEDs to facilitate the features overview, which displays the response of the limiter during peaks and the battery status. At 165 grams, the headphone amplifier is distinctly light-weight and can be operated for up to 12 hours thanks to a high quality 9 V block battery.
  • Model Name: LDHPA1
  • Product Type: headphone amplifier
  • Type: 1-channel stereo
  • Inputs: Main Input (Stereo), 1 x Aux In (Stereo)
  • Input Connections: XLR-F (L + R Input, balanced), 3.5 mm stereo jack (Aux In)
  • Input Impedance: 6 kOhm (XLR In), 10 kOhm (3.5 mm jack)
  • Input Sensitivity: 3 dBu (XLR In), -6 dBV (3.5 mm jack)
  • Max. Input Level: 16 dBu (XLR In), 7 dBV (3.5 mm jack)
  • Protection Circuits: Audio Limiter, Max. Input leveling, Power OFF -Mute relay
  • Headphone Outputs: 1
  • Headphone Output Connectors: 3.5 mm stereo jack
  • Power Output: 2 x 1.65 Vrms / 1% THD 33 Ohm Load
  • Minimal Connected Impedance per Channel: 16 ohms
  • Frequency Response: 20 Hz - 40,000 Hz
  • THD 1 kHz Sine: 0.04%
  • Controls: Power/Volume, Balance L/R, Stereo/Mono (Focus) switch,
  • Indicators: Signal (Green) / Peak (Amber), Battery (low battery: red) / Power LED (Power ON: green)
  • Power Supply: 9 V DC block battery, DC jack
  • Operating Voltage: 9 V DC
  • Power Consumption: Nom. 70 mA / Max. 150 mA
  • Housing Material: plastic
  • Housing Surface: soft-touch
  • Housing Colour: black
  • Width: 80 mm
  • Height: 42.5 mm
  • Depth: 133 mm
  • Accessories (included): belt clip, 1 m 3.5 mm stereo jack cable

Overview

Sound can be perfected with Sennheiserʼs HDVA 600. Delivering authentic sound in its purest form, listeners are treated to a world of sheer listening pleasure. Years of knowledge in audio engineering and innovations in acoustic amplification, resulted in the creation of the HDVA 600. The consistently symmetrical signal processing and extremely low harmonic distortion guarantees an absolutely precise sound. Also, thanks to their pre-amp performance, they are easy to adjust and be connected directly to speakers for optimum audio amplification. In essence, the HDVA 600 provides a spectacular listening experience when paired with any Sennheiserʼs audiophile headphones.

Features
Consistently symmetrical signal processing for maximum sound quality
Symmetrical inputs and outputs simplify integration into a system
High-end ALPS quadruple potentiometer achieve perfect channel equality
Variable gain factor (five stages) for optimized use of low impedance headphones
Sophisticated metal housing to protect against signal scatter and vibration
Solid controls turned from solid metal, providing the utmost in long-term stability

Weight2.00 kg0.30 kg4.00 kg1.58 kg0.05 kg0.40 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 2.00 kg
Weight 0.30 kg
Weight 4.00 kg
Weight 1.58 kg
Weight 0.05 kg
Weight 0.40 kg