Phantom III - 48V Phantom Power Supply Overview

Different condenser microphones specify different amounts of required phantom power.
 As a rule these ratings can range from 48 volts all the way down to 9 volts. Fortunately,
there is some flexibility in terms of matching phantom voltage to your mic. A rough rule
of thumb would be ?more is better.?
For example, a 24-volt condenser mic will run perfectly on 48 volts. In fact, mics rated
at as little as 9 volts can often operate on 48 volts, but you should check with the manufacturer
first. Conversely, a mic will generally perform best driven by not less than its rated voltage
so, for a 48V mic, you would obtain best results with 48 volts of phantom power. The
Phantom III is a great choice for the above needs.

Phantom III - 48V Phantom Power Supply Specifications:

Input Connectors XLR female
Output Connectors XLR male
Frequency Response 10Hz ? 25kHz
Output Phantom Power 48V DC +/- 2V
Output Noise -115 dBV
Current Drain 14mA
Power 18V AC (Adapter included)
Dimensions 5.25x2.75x1.75 inches (130mm x 74mm x 45mm)
Weight 1.3 lbs. (315g)
 

Palmer Pan 48 is a unit for the external power supply of phantom powered appliances. Due to the high current level of a maximum of 20mA, the application is not just limited to condenser microphones. PAN 48 is excellent for supplying phantom powered active DI-boxes. The box has two channels. Specifications: 2 channels, each channel: Microphone input: XLR/f Pin 2 & 3 +48VDC, Pin 1 Ground Output: XLR/m no DC voltage Ground lift switch Phantom power stabilized ±5%. Low ripple, low noise Max. current 20mA totally. LED control. Metal casing 110x110x45mm

The K6P powering module is at the heart of Sennheiser's professional modular
condenser microphone system. It is similar to the K6 powering module but is
powered by 12 - 48 V phantom power only, for use where battery power is not
required (e.g. permanent installations). The K6P can be combined with various
microphone heads to produce microphones with a variety of pick-up patterns.
Matt black, anodised, scratch-resistant finish.
Profile
Powering module for phantom powering with switch-able roll-off filter suitable for
ME 62 - ME 67 microphone heads and -60 versions of MKE microphones,
transmission factor 0 dB at 1 kHz, nominal impedance 200 Ohm, min. terminating
impedance 1 kOhm, max. output voltage 2 V (at 1 kHz), phantom powering 12 V - 48 V,
supply current 2.2 mA, dimensions in mm: ? 22 x 118, resultant length 52 mm,
weight approx. 30 g.

Features
Switchable bass roll-off filter protects against rumble, handling, pop and wind noise
On/off switch
High output, low noise
Transformerless balanced output on 3-pin XLR connector
Delivery Includes
1 K6P powering module
1 MZQ 200 microphone clamp
1 protective carrying case

Technical Data
Nominal impedance  200 Ohm, symm. 
Min. terminating impedance  1000 Ohm 
Output voltage  2 V (1 kHz) 
Power supply  Phantom 12 - 48 V 
Current consumption  2,2 mA 
Dimensions  d 22 x 52 mm (netto) 
Gain  0 dB 

Alctron PS200 Portable 48V Phantom Power Supply for Condenser Microphone Live Broadcast Mic Power Supply

The AKG MPA V L Phantom power adapter with XLR connector for L type MicroMic microphones with integrated bass roll-off switch. This product replaces the AKG MPA III L Phantom Power Adapter, which did not have a bass roll-off switch.