Content |
Phantom II - Two Channel 12V/48 Phantom Power Overview
Condenser microphones usually specify different requirements for their phantom power. These ratings can range from 48 Volts all the way down to 9 Volts. Fortunately, there?s a certain amount of flexibility with matching Phantom Power voltage to your mic. A rough rule-of-thumb would be ?more is better.? For example, a 24-volt condenser mic usually works perfectly with a 48 Volt Phantom Power Suppy. Some mics rated at as little as 9 Volts can operate on voltages up to 48 Volts (check with the manufacturer first). Conversely, a mic will generally perform best driven by not less than its rated voltage. So, for a 48 Volt mic, you would get best performance with 48 Volts of Phantom Power. For all the above, check out the Phantom II. Phantom II - Two Channel 12V/48 Phantom Power Specifications:
Input Connectors 2 x XLR female Output Connectors 2 x XLR male Adapter 12V DC Battery 2 x 9V Power Two 9V batteries (included) or an AC adapter. Dimensions 5.625x1.75x3.625 inches (144mm x 45mm x 92mm) Weight 1.5lb (680g) |
The K6 powering module is the heart of this Sennheiser professional modular
microphone system and can be powered either by its internal 'AA' size 1.5 V
battery or by 12 - 48 V phantom power. The K6 can be combined with different
condenser microphone heads to provide a wide variety of polar patterns. Matt
black, anodised scratch-resistant finish.
Profile
Powering module for battery/phantom powering with switchable roll-off filter, battery
on/off switch with battery test. Suitable for ME 62 - ME 67 microphone heads and
-60 versions of MKE microphones.Transmission factor 0 dB at 1 kHz, nominal
impedance 200 Ohm, min. terminating impedance 1 kOhm, max. output voltage 2 V
(at 1 kHz), power supply: phantom powering 12 - 48 V or 1.5 V (AA size)alkaline
battery, supply current 2.2 mA, battery life approx. 150 h, dimensions in mm:
? 22 x 155, resultant length 94 mm, weight approx. 45 g.
Features
Switchable bass roll-off filter protects against rumble, handling, pop and wind noise
On/off switch with battery test
High output, low noise
Transformerless balanced output on 3-pin XLR connector
Delivery Includes
1 K6 powering module
1 MZQ 200 microphone clamp
1 AA battery
1 protective carrying case
Technical Data
Nominal impedance 200 Ohm
Min. terminating impedance 1000 Ohm
Output voltage 2 V
Power supply Phantom 12 - 48 V 1x Typ IEC LR 06
Current consumption 2,2 mA
Operating time (Battery) max. 150 h
Dimensions d 22 x 94 mm (netto)
Weight ca. 45 g
Gain 0 dB
| The MX1BP is a battery-powered preamplifier designed to be used with Microflex? or other condenser microphones. It allows use of these microphones in situations where phantom power is not available. Features * 4-pin Tini Q-G? connector allows use with a variety of condenser microphones * Power LED Indicator indicates power status to the preamplifier * Mute/On switch attenuates microphone without turning off preamplifier * Belt clip allows mobility while using lavalier and headset microphones * Preamplifier operates on 9 V battery or phantom power * Features 3.7 m (12 ft) cord with attached male XLR connector | PS418D
Pre-Amplifier
The condenser miniature microphones, need phantom power to work. The PS418D is just what they need. It can be powered by phantom power or battery, and switchable low cut filter helps to reduce low band noise.
Features:
• Two options for Power Requirements: phantom or battery.
• Low-cut filter switch.
• Transistor output transformer circuit.
Specification:
Frequency Response: 25-20,000 Hz
Output Impedance: phantom 200Ω; battery 270Ω
Min. Load Impedance : 1000Ω
Power Requirements: phantom 9-52VDC,2mA; battery 1.5V AA/UM3
Low Frequency Filter: 80Hz @ 12dB / oct
Connector: TA3M (input), XLR3M (output)
Dimension(WxHxD): 63X84X22.5mm (2.48"x3.3"x0.89")
Weight: 245 g
Packaging: white box |
The Radial SB-48 is a high performance phantom power generator that employs a non-radiating charge pump circuit to create a stable, ripple-free 48 volt supply for active direct boxes and condenser microphones. The stereo design features XLR inputs and outputs with a choice of 48V and 12V operation. The SB-48 is powered by a single 15VDC 400 milliamp supply that is included. The connector may be locked into place using a retention clamp. As with all Radial products, the SB-48 is manufactured in Canada from solid steel and powder coated for years of great looks! |
The AKG MPA V L Phantom power adapter with XLR connector for L type MicroMic microphones with integrated bass roll-off switch. This product replaces the AKG MPA III L Phantom Power Adapter, which did not have a bass roll-off switch. |
Reviews
There are no reviews yet.