ARX EC-2 STEREO 2WAY-MONO 3WAY 24dB ACTIVE CROSSOVER

The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers.
It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on
the back panel selecting either mode.

Features
Ultra low noise circuitry
Totally phase aligned at crossover point
Switchable Dual Channel 2 way or Single Channel 3 way
Unique 'semi-fixed' crossover point
24dB per octave (Fourth Order) Linkwitz-Riley filters
Separate Summed Mono Output
Balanced Inputs and Outputs
Built in High Pass filters
Intuitive, 'user friendly' layout
Flawless performance in any audio environment

Tamper-Proof Crossover Points
The crossover points are determined internally by the value of 4 resistors per channel; changing
the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of
externally adjusted crossover points, making the crossover points tamper-proof once they are set.
Idle fingers can't fiddle with the crossover points and create havoc with the system!
As a handy guide, a list of common crossover points and their corresponding resistor values are
printed inside the unit's lid, and also set out in the Owner's Manual.
On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid
and High in single channel 3 way mode, with corresponding Outputs on the rear panel.

Balanced Inputs and Outputs
EC-2 has Balanced Inputs and Outputs, on XLR connectors.
The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low
feed (e.g. Left and Right full-range plus a single Sub Bass speaker).
High Pass Filter
There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers
and waste amplifier power.
In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of
differing sensitivities.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard
IEC connector, with built-in fuse and voltage change switch.
Uncompromising Audio Quality
Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels.
It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth
Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the
crossover region.
From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX
EC-2 is a crossover that is suited to any application that requires flawless, transparent sound.
You'll never compromise on Quality when you choose ARX

T E C H N I C A L S P E C I F I C A T I O N S

Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 21 dB
CMRR >45 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 21dB
Frequency Response 30Hz-20KHz +or- 0.5dB
Note: 30 Hz is a function of the High Pass filter
Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted
Distortion 004% THD,0dB,1KHz
Dynamic Range 111 dB
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm
Input Connector type XLR
Output Connector type XLR
Crossover point frequencies are changed internally by varying the value of 4 resistors
per channel.

Front Panel Controls
Low and High Output controls for 2 way mode
Low, Mid and High Output controls for 3 way mode
Marker panels for labelling crossover assigns
2 way/ 3 way status LEDs
Rear Panel
Balanced XLR Inputs and Outputs
Additional summed mono Low output
2 way / 3 way mode switch

The DX 4008 is a complete 4 input - 8 output digital loudspeaker management system designed for the touring or fixed sound installation markets.

The absolute latest in available technology is utilized with 32-bit (40-bit extended) floating point processor and high performance 24-bit Analog Converters. The high-bit DSP prevents noise and distortion induced by truncation errors of the commonly used 24-bit fixed-point devices. A complete set of parameters include I/O levels, delay,polarity, 6 bands of parametric EQ per channel, multiple crossover selections and full function limiters. The DX 4008 can be controlled or configured in real time on the panel or with the intuitive PC GUI accessed via the RS 232 interface. Software upgrade for CPU and DSP via PC keeps the device current with newly developed algorithms and function once available. Multiple setup storage and system security complete this professional package.

Based on a two-in, six-out topology, the DC-One is designed primarily for users of small-to-medium sized sound systems in both mobile and installed applications. While the unit is an all-new development based on a powerful SHARC processor, it is 100 percent compatible with all settings from other Electro-Voice signal processors. A large part of DC-Oneʼs development was aimed at ensuring that users can easily handle its serious digital horsepower and high-end audio performance. Free. PC-Editor software is available, or the DC-One can be operated via the front panel.   A/D Conversion    24-Bit Delta-Sigma
A/D Conversion    24-bit/sigma-delta (linear phase) 128 times oversampling
Analog Inputs    2 XLR (Electronically Balanced), 2 XLR THRU OUT (Electronically Balanced)
Analog Outputs    6 XLR (Electronically Balanced)
Control Protocol    Front Panel USB Connector
D/A Conversion    24-bit/sigma-delta 128 times oversampling
D/A Conversion    24-Bit Delta-Sigma
Data Format    24-Bit
Digital Inputs    1 XLR AES/EBU (2 Ch)
Dynamic Range    111 dB (unweighted, band limited 22 Hz - 22 kHz)
Electronics Type    Processor
FIR-Drive    No
Frequency Response    10 Hz - 22 kHz (±0.5 dB)
Input Impedance (Balanced)    10 kΩ
Internal Processing    32-Bit Floating Point
Mains Voltage    100-240 VAC
Maximum Input Voltage    8.7 V / +21 dBu (Without -6 dB Analog Pad Engaged)
Maximum Output Voltage    8.7 V / +21 dBu
Nominal Input Voltage    1.23 V / +4 dBu
Nominal Output Voltage    1.23 V / +4 dBu
Output Impedance (Balanced)    50 Ω
Power Consumption    25 W
Sample Rate    48 kHz
THD+N    < 0.01% (band limited 22 Hz - 22 kHz)
Height    1RU 44.45 mm (1.75“)
Width    482.6 mm (19“)
Depth    355.6 mm (14“)
Weight Net    4.6 kg (10.14 lbs) 

With 12 inputs and 6 outputs and Ethernet control the dbx ZonePro? 1260 and 1261
are the newest members of the ZonePro? family providing a complete suite of signal
processing and control for Commercial Audio applications.
Designed to offer superior system sonic performance and flexibility, the 1260/1261 deliver
the highest quality tools available. Even the input and outputs connectors were chosen for
their standard usage and reliability. The ZonePro products offer Euroblock connectors for
balanced signals and RCA connectors for interfacing with consumer equipment often used
in commercial applications; there is also a simple analog input buss that allows inputs to be
sent from one unit to the next for unit and job scalability. The 1260 and 1261 provide every
necessary processing tool, from the input processing like gain control and EQ available on all
inputs to highly sophisticated and specific functions such as selectable paging microphone
processing including Gating, De-Essing, Auto Gain Control, Compression and Feedback
Suppression. The heart of the ZonePro products is the Routing module that provides of course
Primary Source Selection but also Source Ducking for Paging and Priority Override. The outputs
also offer a wealth of processing designed for commercial applications like our patent-pending
AutoWarmth? function that was co-developed with JBL to provide natural low frequency extension
at any signal level. Each output also offers EQ, Bandpass and Crossover filters, Limiting and Delay
for system optimization. With the ZonePro? every tool is at your disposal to maximize the response
of your system.
Beyond processing, the ZonePro? products offer multiple forms of control to further extend the
versatility of your system. From easy-to-use wall panel Zone Controllers for standard end-user
functions like source select and volume control to advanced system control including a built-in
Real Time Clock that can provide programmable system changes throughout the day or week.
For system setup and monitoring the ZonePro Designer software provides an intuitive interface
and a speedy setup Wizard for configuring and editing all system parameters. The addition of
Ethernet control means that not only will it work with standard network equipment, but it can also
be accessed from remote dialup locations or from wireless access points.
The ZonePro? 1260 and 1261 will take your Commercial Audio system to the next level with advanced
processing, versatility and control.
 
? Advanced Feedback Suppression (AFS?)
? Autowarmth?
? Auto Gain Control
? Compression
? Limiting
? Noise Gating
? Notch Filtering
? Bandpass and Crossover Filters
? Parametric EQ
? Security Lockout
? Wall Panel Control
? RS-232 Control
? IEC, UL and CSA Approvals
 
ZonePro? 1260/1261 Specifications    
      
ANALOG INPUT
Number of Inputs:
12 Total (2) Switchable mic or line, (8) RCA, and (1)
S/PDIF
Connectors:
Euroblock (Line and Mic) RCA (Source)
Type:
Impedance (Euroblock):
> 50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):
>25kΩ Unbalanced, RF Filtered
Max input line level:
+20dBu Mic/Line, +12dBu RCA
CMRR:
> 40dB, typically >55db @ 1kHz
Mic Pre gain:30 to 60dB
Mic EIN:
> 118dB, 22Hz-22kHz, 150Ω Source Impedance
Mic Phantom Power:
15V
 
ANALOG OUTPUTS
Number of Outputs 6
Connectors: Euroblock
Type:
Electronically balanced, RF filtered
Impedance:
120 ohms balanced, 60ohm unbalanced
Max Output Level: +20dBu
 
A/D PERFORMANCE
Type:
dbx Type IV? conversion system
Dynamic Range line:
>113 dB, A-weighted, >110 dB unweighted
Type IV dynamic range:
>119 dB, A-weighted, 22kHz BW
>117 dB, A-weighted, 22kHz BW
Sample Rate: 48kHz
 
D/A PERFORMANCE
Dynamic Range:
112 dB A-weighted, 109dB unweighted
 
SYSTEM PERFORMANCE
Dynamic Range:
>110 dB A-weighted, >107dB unweighted
THD+N:
0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response:
20Hz - 20kHz, +/-0.5dB
Interchannel Crosstalk:
>80dB typical
Crosstalk input to output:
>80dB
Propagation Delay
0.6 msec
 
POWER REQUIREMENTS
Operating Voltage:
100-240 VAC, 50/60Hz
Power Consumption:
27 Watts
 
Physical:
Weight:
6.8 lbs.(3.1 kg) Shipping weight 8.8 lbs. (4.0 kg)
Dimensions:
1.75? H x 5.75? D x 19? W

The VENU360 provides all the processing and flexibility you need between your mixer and amplifiers to optimize and protect your loudspeakers. With the latest advancements in dbxʼs proprietary AutoEQ and AFS algorithms, additional input channels, ethernet control via an Android, iOS, Mac, or Windows device, and updated wizards, the DriveRack VENU360 continues the DriveRack legacy of great-sounding, powerful, and affordable loudspeaker management processors, for a whole new generation.