The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers.It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on the back panel selecting either mode. Features Ultra low noise circuitry Totally phase aligned at crossover point Switchable Dual […]
The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers. It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on the back panel selecting either mode.
Features Ultra low noise circuitry Totally phase aligned at crossover point Switchable Dual Channel 2 way or Single Channel 3 way Unique ‘semi-fixed’ crossover point 24dB per octave (Fourth Order) Linkwitz-Riley filters Separate Summed Mono Output Balanced Inputs and Outputs Built in High Pass filters Intuitive, ‘user friendly’ layout Flawless performance in any audio environment
Tamper-Proof Crossover Points The crossover points are determined internally by the value of 4 resistors per channel; changing the resistor value changes the crossover point. This ‘semi fixed’ method avoids the pitfalls of externally adjusted crossover points, making the crossover points tamper-proof once they are set. Idle fingers can’t fiddle with the crossover points and create havoc with the system! As a handy guide, a list of common crossover points and their corresponding resistor values are printed inside the unit’s lid, and also set out in the Owner’s Manual. On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid and High in single channel 3 way mode, with corresponding Outputs on the rear panel.
Balanced Inputs and Outputs EC-2 has Balanced Inputs and Outputs, on XLR connectors. The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low feed (e.g. Left and Right full-range plus a single Sub Bass speaker). High Pass Filter There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers and waste amplifier power. In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of differing sensitivities. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage change switch. Uncompromising Audio Quality Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels. It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the crossover region. From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX EC-2 is a crossover that is suited to any application that requires flawless, transparent sound. You’ll never compromise on Quality when you choose ARX
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 21 dB CMRR >45 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 21dB Frequency Response 30Hz-20KHz +or- 0.5dB Note: 30 Hz is a function of the High Pass filter Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB ‘A’ weighted Distortion 004% THD,0dB,1KHz Dynamic Range 111 dB Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm Input Connector type XLR Output Connector type XLR Crossover point frequencies are changed internally by varying the value of 4 resistors per channel.
Front Panel Controls Low and High Output controls for 2 way mode Low, Mid and High Output controls for 3 way mode Marker panels for labelling crossover assigns 2 way/ 3 way status LEDs Rear Panel Balanced XLR Inputs and Outputs Additional summed mono Low output 2 way / 3 way mode switch
Weight
5.00 kg
Reviews
There are no reviews yet.
Be the first to review “ARX EC-2 STEREO 2WAY-MONO 3WAY 24dB ACTIVE CROSSOVER” Cancel reply
Flexible routing configurations for all standard mono and stereo output operating modes
2 analog inputs and 6 analog outputs (XLR)
Active crossover with Bessel, Butterworth and Linkwitz-Riley filter with slopes up to 24 dB/octave
Up to 30 user presets storable in the device via software
Input sensitivity digitally adjustable
Inputs and outputs with 4-digit LED level meter as well as clip and limit LED indicator
Mute switch with LED indicator per output
7-band parametric EQ per output
Up to 7 ms signal delay adjustable for the outputs
Output limiter with adjustable limits and automatic attack and release settings as overload protection for your amplifying system
Switchable phase
Lock function for prevents undesired changes to settings
Sample rate: 67 kHz
(19") 48.3 cm rack installation 1 U
Compatible with Win XP, Win Vista, Win 7, Win 10, OS X 10,5 or better
Content
The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers. It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on the back panel selecting either mode.
Features Ultra low noise circuitry Totally phase aligned at crossover point Switchable Dual Channel 2 way or Single Channel 3 way Unique 'semi-fixed' crossover point 24dB per octave (Fourth Order) Linkwitz-Riley filters Separate Summed Mono Output Balanced Inputs and Outputs Built in High Pass filters Intuitive, 'user friendly' layout Flawless performance in any audio environment
Tamper-Proof Crossover Points The crossover points are determined internally by the value of 4 resistors per channel; changing the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of externally adjusted crossover points, making the crossover points tamper-proof once they are set. Idle fingers can't fiddle with the crossover points and create havoc with the system! As a handy guide, a list of common crossover points and their corresponding resistor values are printed inside the unit's lid, and also set out in the Owner's Manual. On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid and High in single channel 3 way mode, with corresponding Outputs on the rear panel.
Balanced Inputs and Outputs EC-2 has Balanced Inputs and Outputs, on XLR connectors. The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low feed (e.g. Left and Right full-range plus a single Sub Bass speaker). High Pass Filter There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers and waste amplifier power. In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of differing sensitivities. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage change switch. Uncompromising Audio Quality Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels. It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the crossover region. From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX EC-2 is a crossover that is suited to any application that requires flawless, transparent sound. You'll never compromise on Quality when you choose ARX
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 21 dB CMRR >45 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 21dB Frequency Response 30Hz-20KHz +or- 0.5dB Note: 30 Hz is a function of the High Pass filter Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted Distortion 004% THD,0dB,1KHz Dynamic Range 111 dB Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm Input Connector type XLR Output Connector type XLR Crossover point frequencies are changed internally by varying the value of 4 resistors per channel.
Front Panel Controls Low and High Output controls for 2 way mode Low, Mid and High Output controls for 3 way mode Marker panels for labelling crossover assigns 2 way/ 3 way status LEDs Rear Panel Balanced XLR Inputs and Outputs Additional summed mono Low output 2 way / 3 way mode switch
The LD Systems X223 is a stereo 2 way / mono 3 way crossover in standard 19"/1U rack format. Its rugged construction, high quality and robust knobs as well as the integrated power unit are rarities in this price range. It provides a mono sub output, an adjustable crossover frequency for each channel, adjustable LF/HF and input gains, phase reverse controls, switchable 40 Hz High-Pass filters and symmetrical XLR In- and Outputs. With the LD Systems X223 you get a crossover fulfilling the professional standards and offering great quality and sound characteristics.
Product type
Signal Processors
Version
2-way stereo/3-way mono
Frequency response
20 - 20.000 Hz
Dynamic range
106 dB
Signal-to-noise ratio
> 93 dB
Total Harmonic Distortion (THD)
< 0.004 %
Crosstalk
< - 80 (20 - 20.000 Hz) dB
Max. input level
+21 (balanced or unbalanced) dBu
Max. output level
+21 (balanced or unbalanced) dBu
Input impedance (kOhms)
50000 kOhm
Output impedance
200 Ohm(s)
Controls
2 x crossover frequency low/high, 2 x crossover low/mid, 2 x high gain, 2 x highpass (40 Hz), 2 x input gain, 2 x low gain, 2x frequency switch x1/x10, 4 x inv switch, LF sum, Mono/stereo mode
Indicators
2 x clip, 2 x crossover x 10, 2 x highpass, 4 x inv., mono, stereo
Line inputs
2
Line input connectors
XLR
Line outputs
4
Line output connectors
XLR
Mains connector
IEC socket
Operating voltage
220 V AC - 240 V AC
Width
482 mm
Height
44.5 mm
Depth
153 mm
Weight
2,6 kg
Power supply:
100-240 V AC, 50/60 Hz
6 V DC 800 mA
Power connection:
Mains input via Coaxial power connector (M) mounting version power supply cord with AC adapter (provided)
Input: line via 2 x 3-pin XLR
Output: line via 6 x 3-pin XLR
Crossover frequency:
20-20000 Hz
Max. level:
Input: +22 dBu
Output: +9 dBu
USB port:
Typ B
PC connect:
DXO Software via USB, firmware can be updated
Housing design:
(19") 48.3 cm rack installation 1 U
Dimensions:
Width: 48,3 cm
Depth: 12,8 cm
Height: 4,45 cm
Weight:
1,77 kg
Operating system:
Win XP, Win Vista, Win 7, Win 10, OS X 10,5 or better
Providing 48-bit filter algorithms, 24-bit AD/DA conversion and a dynamic range of 115 dB, the DSP 244 sets new standards for digital loudspeaker controllers and processors. The DSP 244 is an universal Digital Sound System Processor that provides 2 inputs and 4 outputs; plus internal summing of the inputs 1 and 2. Via matrix it is possible to assign the outputs to any input or to the sum of the inputs. It is further possible to establish the following configurations: Stereo or Dual 2-Way systems, 3-Way + Direct and 4-Way systems, each with Mono Subchannel, but also full range systems. High and low-pass filters are provided for the frequency crossover functions in all operation modes. The selection includes Linkwitz-Riley, Butterworth and Bessel type filters with switchable slopes between 6, 12, 18 and 24 dB/oct. A huge number of additional filters offers extremely flexible correction of the frequency response. Each input incorporates a 5-band equalizer, allowing to assign high and low-pass, high and low-shelving or parametric peak-dip filters to its individual filter sections. Next to the frequency crossover filters, four additional filters are employed in each output channel, which also can be set to work as high or low-pass, high or low-shelving filters, parametric peak-dip filters, or all-pass filters. Additional filtering is provided through 2. order high-passes for the realization of B-6 alignment, or special LPN-filters (Low-Pass Notch filters) for correcting the frequency and phase responses of optimally vented woofer cabinets. Each channel additionally provides a delay, a polarity switch, a programmable level control and a digital compressor / limiter while the master delays are located in the input channels. Datasheets / ManualsBrochure (309KB)
Mains voltage 90 - 250 V AC / 50 - 60 Hz Power consumption 20 watts Safety class I Inputs 2 x XLR IN, electronically balanced, transformer optional available 2 x XLR OUT (Direct Out) Input voltage (nominal) 1.55 V / + 6 dBu Max. input voltage 24.5 V / + 30 dBu Input impedance 20 kohms Common mode rejection > 40 dB AD-conversion 24-bit, Sigma-Delta, 128 times oversampling, linear phase Outputs 4 x XLR OUT, electronically balanced Output voltage (nominal) 1.55 V / + 6 dBu Max. output voltage 8.7 V / + 21 dBu Output impedance
Crossover Xover 352921-003 / 364246-001 for the JBL JRX-112M, JRX112M, and JRX 112M cabinet
JBL JRX-112M Specifications:
2-Way
1.8kHz Crossover Frequency
250W RMS / 1000W Peak
8 ohm Nominal Impedance
(1) 1/4" Jack
(1) Neutrik Speakon Jack NL4MP (both jacks can be used for input & output)
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.