| Content |
The 4.24GS and 2.24GS allow for the installation of multiple channel graphic equalizers ]where tamperproof, sound shaping equalization is required. Control and programming of either product is easily achieved from the 4.24G Main Unit, 4.24RD Remote Control, through the use of Ashly's exclusive Protea System Software running on a PC, or by a MIDI controller. The Protea 4.24GS is housed in an all-steel, 2RU chassis, and has four independent channels of fully programmable 28-band graphic EQ with with limiter, high- and low-pass filter, and time delay functions. The 2.24GS offers the same specs and features in a single rack-space, two-channel unit.
Each channel allows for 28 bands of 1/3-octave, ISO centered, constant Q filters, ranging from 31Hz to 16kHz. High and low pass filters are 24dB/octave adjustable from 20Hz to 10.6kHz and 33Hz to 20kHz, respectively. Time delay is adjustable up to 1.364 seconds.
Other features include 24-bit A/D-D/A conversion, 24-bit/100MHz digital processing, RS-232, and MIDI interface, linkable channels, +6dB/-infinity master gain, and 128 preset locations. Both units display individual channel numbers with 7-segment displays. Discrete LEDs indicate signal present and signal clip levels. Rear-panel connections include balanced XLR and 1/4" ins/outs for each channel, RS-232, MIDI In, Out/Thru, and Ashly's exclusive digital remote control protocol via two standard XLR connectors.
| |
|
| Type: |
Electronically balanced/unbalanced, RF filtered |
| Impedance: |
Balanced 40 kOhm, unbalanced 20 kOhm |
| Max Input Level: |
>+21dBu balanced or unbalanced |
| CMRR: |
>40dB, typically >55dB at 1kHz |
| OUTPUTS |
| Connectors: |
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip |
| Type: |
Impedance-balanaced/unbalanced, RF filtered |
| Impedance: |
Balanced 200 ohm, unbalanced 100 ohm |
| Max Output Level: |
>+21dBu balanced/unbalanced into 2 kOhm or greater
>+18dBm balanced/unbalanced (into 600 ohm) |
| SYSTEM PERFORMANCE |
| Bandwidth: |
20Hz to 20kHz, +0.5/-1dB |
| Frequency Response: |
50kHz, +0.5/-3dB |
|
+/-15dB range |
+/-6dB range |
| Dynamic Range: |
109dB |
115dB |
| Signal-to-Noise: |
90dB |
97dB |
| THD + Noise: |
|
|
The class-A circuit used in the EQ-73 is similar to the eq section in the classical 1073 module, without the high pass filter. Additional frequencies have been added and the mid frequency band uses two inductors, the higher value of the second one is used for the two lowest frequencies, 160 Hz and 240 Hz, to achieve a suitable response.
The sound character is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
The EQ-73 has stepped frequency controls that offers a wide selection of frequencies from 20 Hz to 24 kHz.
The Low and High frequency bands are shelving and the mid frequency band is of the bell type.
The control range is +/-15 dB for the two lower bands and +/- 18dB for the high frequency band.
There are separate bypass switches for all three bands.
The EQ-73 is made to be used together with one of our PRE-73 models that has an Insert jack. It can also be used with many other units that has a low level insert jack.
Combining a PRE-73 and an EQ-73, and using a UNITE rack kit to mount them together, one will get a 19-inch 1073-style unit at a low cost and with a great sound!
FEATURES
- Vintage Style electronics. No intergrated circuits in the signal path
- 3-band with a dual inductor based mid frequency band
- Stepped frequency selection
- A wide selection of frequencies from 20 Hz to 24 kHz
- Control range up to +/- 18 dB
- Separate Bypass switches for each band
- Tantalum capacitors in the signal path
- Made to be used together with one of our PRE-73 models with an Insert jack or any other unit with a low level Insert jack
- TRS jack for in-and output connection, the nominal working level is around 18 dBu
- Selectable ground lift switch
- External power supply to avoid interaction with the audio circuits
- Great sound that suits most sound sources and genres
- A solid build quality that will last many years of normal use
|
The Rane ME 15S microGraphic Equalizer is a two-channel, 2/3-octave design with 20 mm sliders in a single rack space unit. It features a Range switch for high slider resolution in the ±6 dB mode, equivalent resolution to 45 mm sliders found on the DEQ 60L. The ±12 dB mode provides a wide range of control over system audio.
The active filter sections feature Raneʼs innovative constant-Q (constant bandwidth) design. Constant-Q means the bandwidth of each individual filter is guaranteed to be narrow enough to prevent unwarranted interaction between filters, yet wide enough to produce exactly the type of correction curve demanded by even the most unusual acoustic surroundings. This differs dramatically from conventional designs of the past, encumbered with the unfortunate characteristic of changing bandwidth when changing boost/cut amounts.
Front panel controls and indicators include an overall rotary Level control for each channel as well as Overload indicators. Passive pushbutton Bypass switches feature LED indicators, avoiding ambiguity by being on when the unit is Bypassed. (A passive Bypass switch requires no power to operate. This allows completion of the audio path should power fail in the ME 15S.)
Inputs and Outputs are electronically balanced designs, capable of unbalanced operation when required. They accept and drive all possible signal levels into normal load impedances. Balanced applications choose between the XLR or 1/4" Tip-Ring-Sleeve connectors. Unbalanced sources also may tie to the ME 15S through mono 1/4" connectors (no ring connection).
Features - Constant-Q Bandwidth Design
- Overall Level Controls and Passive Bypass Switches
- 20 mm Filter Slide Controls with ±6 dB or ±12 dB Slider Range
- Infrasonic, Ultrasonic, & RFI Filters
- Balanced XLR and 1/4" TRS Inputs and Outputs
- Universal internal switching power supply (100-240 VAC)
| INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typicall >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: |
- Professional 15-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated mono subwoofer output with adjustable crossover frequency
- Additional low-cut filter removes unwanted frequencies, e.g. floor rumble
- Highly accurate 4-segment LED output metering and input gain controls for easy level setting
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
- 3-Year Warranty Program*
- Designed and engineered in Germany
|
Reviews
There are no reviews yet.