| Content |
The DPX Series was created in response to our dealers, contractors and users requesting a simple solution requiring general EQ and comp/limiting. Two products have been developed, the DPX-100 Graphic Equalizer & Compressor/Limiter and DPX-200 Parametric Equalizer & Compressor/Limiter. Using proven circuitry from our popular MQX and PQX series equalizers and combining
these features with our CLX series compressor/limiters provides two tools no audio system
should be without. By combining the features and benefits of two processors into one unit,
the result is two powerful tools providing a simple solution to everyday audio applications.
The EQ section of the DPX-100 is a 15-band, constant Q, 2/3 octave, ISO center, precision
wein bridge filter design. Other EQ features are: frequency range from 25Hz to 16KHz,
selectable 15dB or 6dB range, 25mm faders with 'center off' position, EQ in/out switch,
signal present and clip LEDs and switchable 18dB/octave -20Hz high pass filter. Two separate inputs are available in the DPX-200; a microphone preamp with input pad
and a line input. An input select switch and input level control are located on the front
panel. The EQ section consists of 4 bands of filtering; two full-bandwidth parametric EQs
as well as a low-shelf and high-shelf filter. Other EQ features are: in/out switching for
each filter, cut and boost of 15dB, signal present and clip LEDs, and master EQ level control.
The compressor/limiter section uses peak detection circuitry and has individual controls
for gain, threshold, ratio, attack, release and output level. More compressor/limiter features
include: in/out switch, 11-stage LED gain reduction meter, selectable 11-stage LED input/output
level meter, and a detector patch point for frequency-selective limiting or ducking. Additional features of the DPX-100 and DPX-200 are: the equalizer section and
compressor/limiter may be used independently or chained together in series, balanced
XLR and inputs and outputs, extremely low noise and distortion, internal power supply
and Ashly's five-year worry-free warranty.
| Separate Mic Pre and Line Inputs | | 2 fully parametric bands | | Parametric filters tunable from 20Hz to 20KHz | | Adjustable bandwidth from 3 1/3 to 1/20 of an octave | | High and Low Shelf filters | | True reciprocal curves | | Individual band in/out bypass switching | | Balanced Inputs and Outputs | | XLR, 1/4" TRS audio connections | | Five Year Warranty |
|
DBX 2215 Dual 15-Band Graphic Equalizer with Noise Reduction
It's amazing. One little button. So much effect. dbx? Type III? Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one's surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see.
But hey, Roger wasn't about to stop there. PeakPlus? Limiter. Who knows more about limiting than the folks at dbx; nobody... that's who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in." Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.
20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You'll see, with the 20 Series EQs you get MORE!!!
SPECIFICATIONS:
|
INPUT
| |
Connectors:
|
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
| |
Type:
|
Electronically balanced/unbalanced, RF filtered
| |
Impedance:
|
Balanced 40k ohm, unbalanced 20k ohm
| |
Max Input Level:
|
>+21dBu balanced or unbalanced
| |
CMRR:
|
>40dB, typically >55dB at 1kHz
| |
OUTPUTS
| |
Connectors:
|
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
| |
Type:
|
Impedance-balanaced/unbalanced, RF filtered
| |
Impedance:
|
Balanced 200 ohm, unbalanced 100 ohm
| |
Max Output Level:
|
>+21dBu balanced/unbalanced into 2k or greater
>+18dBm balanced/unbalanced (into 600)
| |
SYSTEM PERFORMANCE
| |
Bandwidth:
|
20Hz to 20kHz, +/-0.5dB
| |
Frequency Response:
|
50kHz, +0.5/-3dB
| |
Noise Reduction In:
|
(+/-6 and +/-15dB range):
| |
Signal-to-Noise:
|
>102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
| |
Dynamic Range:
|
>120dB, unweighted
| |
Noise Reduction Out:
|
(+/-6dB range):
| |
Signal-to-Noise:
|
>94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
| |
Dynamic Range:
|
>112dB, unweighted
| |
Noise Reduction Out:
|
(+/-15dB range):
| |
Signal-to-Noise:
|
>90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
| |
Dynamic Range:
|
>108dB, unweighted
| |
THD + Noise:
|
| |
The AD2055 combines 100% discrete, pure class A signal amplifiers with state-of-
the-art passive and active filter topologies. The AD2055's unique circuitry delivers
very high resolution transient detail at the operational extremes of real world equalization
demands. The AD2055 auto-bias DC servo loop control eliminates the need for all
interstage capacitor coupling. The AD2055 breathes life into all musical performances!
AD2055 FEATURES
Pure Class A, 100% discrete design
Smooth musical detail and sonic excellence
Minimum audio signal path
Dual mono operation
Transparent active and passive filter design
High headroom +30dB Very low noise -94dB
Fully balanced inputs and outputs
DC coupled, no transformers in audio path
Switched frequencies in high and low bands
Mid bands use X10 frequency for extended range
Wide bandwidth -3dB 1Hz to 450kHz
Low distortion less than 0.5% THD and IMD
All signal routing with sealed silver relays Conductive
plastic potentiometers for low noise
External 150W toroidal power supply 100% discrete
power supplies for audio path
Long lasting, stainless steel hardware
SONIC EXCELLENCE
The Avalon AD2055 Pure Class A music equalizer is the most powerful, low noise
parametric equalizer available today. Designed to optimize absolute signal integrity
and musical performance, the AD2055 combines the best of active and passive filter
topologies with sonic excellence unequaled by lesser designs. The AD2055 is the
perfect solution for two buss music-program equalization, special instrument EQ and
FX applications and ultra high performance mastering studio's.
Features include state-of-the-art, balanced 100% discrete, Pure Class A signal amplifiers,
practical user features and rugged hardware designed to deliver true high performance
audio for many years.
PASSIVE-ACTIVE FILTER DESIGN
Avalon equalizers feature the unique combination of both active and passive filter EQ designs.
This special combination enables the AD2055 to deliver high speed transient detail at the
operational extremes of real-world equalization demands. The passive high and low bands offer
alternate musical tone range to the full function active parametric mid bands. Passive equalizers
have long been a favorite with music lovers around the world. Full bodied, powerful (up to +/-32dB,
64dB range !) and sweet frequency selections are the benefits of the passive high-low EQ bands.
The full bandwidth twin mid bands provide variable frequency selection (X10 frequency multipliers
for very wide range), variable Q (width) and amplitude control.
MINIMUM SIGNAL PATH DESIGN
Avalon's advanced true symmetry design offers high-voltage, large headroom, extended bandwidth
and very low noise. The use of 100% discrete, Pure Class A signal amplifiers give the serious music
professional unlimited sonic character and a natural harmonic detail that enhances the program
material and becomes one with the music itself. The Avalon AD2055 breathes life!
AD2055 SPECIFICATIONS
Circuit Topology High-voltage 100% discrete, balanced and symmetrical
Class A
Output Gain Range Unity Gain
Maximum Input Level +30dB balanced XLR pin 2 hot
Maximum Output Level +32dB balanced 600 ohms, DC coupled, high-current
discrete Class A
Input / Output Type XLR type, pin 2 hot balanced
Noise 20kHz Unweighted -94dB (EQ in)
Distortion THD, IMD 0.5% (typical 0.05% at +6dB 1kHz)
Frequency Response -3dB 1Hz to 450kHz (input band limited)
Equalizer Type Passive high and low bands plus two fully parametric mid
bands
Bypass Hard-wire relay bypass for equalizer in-out
Low Band F1 Passive, amplitude to -32dB to +32dB shelf or peak-dip curve
F1 Frequency Range Switched 10 position 18Hz, 25, 30, 50, 72, 100, 150, 215,
300, 450Hz
Mid Band F2 Active, amplitude to -16dB to +16dB peak-dip curve
F2 Frequency Range Variable 35Hz to 450Hz (x10) 350Hz to 4k5Hz, Q (width)
0.3 to 3.0
Mid Band F3 Active, amplitude to -16dB to +16dB peak-dip curve
F3 Frequency Range Variable 160Hz to 2k0Hz (x10) 1k6Hz to 20kHz, Q (width)
0.3 to 3.0
High Band F4 Passive, amplitude to -26dB to +26dB shelf or peak-dip curve
F4 Frequency Range Switched 10 position 1k5Hz, 2k5, 3k5, 5k, 7k2, 10k, 12k5,
15k, 20k, 25kHz
AC-DC Power External AC supply, 150w toroidal transformer, 4 pin cable 90v
isolated,
(B2T Power Supply Included) 100-240v selectable 50/60Hz, 150w max
Dimensions 19 x 3.5 x 12 in (482 x 88 x 305mm)
Shipping weight 30lbs (13.6 kg)
|
1215 Dual 15-Band Graphic Equalizer
The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.
- Switchable boost/cut ranges of ±6 or ±15 dB
- Electronically balanced/unbalanced inputs
- Servo balanced/unbalanced inputs
- RF filtered inputs and outputs
- XLR, Barrier Strip, and 1/4" TRS connectors
- -12dB/+12dB input gain range
- 18dB/octave 40Hz Bessel low-cut filter
- Chassis/signal ground lift capability
- Internal power supply transformer
- Power-off hardwire relay bypass with 2-second power-up delay
|
iEQ-15 Dual 15-Band Graphic EQ with Type V? NR and AFS?
With an EQ heritage that has produced countless industry standard
patents and dates back more than 30 years, the dbx iEQ-31 easily
lives up to the dbx legacy of uncompromised sonic integrity. In
addition to unsurpassed equalization specs, the iEQ-15 also offers
the built-in necessities which include AFS? feedback Suppression,
Type V? noise reduction and PeakStopPlus? limiting. Besides
including two 15-band channels of 2/3-octave equalization, the iEQ-15
also offers +12 dB input gain range; switchable +6 or +15 dB boost/cut
range, 40mm faders, XLR, 1/4'' and Euroblock inputs and outputs,
nonconductive nylon sliders; and an intuitive user interface with comprehensive
output and gain reduction metering. As always, the inevitable result of our
meticulous attention to detail and top-quality componentry is exceptional
sound, performance, and reliability.
The iEQ series represents a major step forward in the performance of EQs.
The iEQ series is now able to offer state-of-the-art digital EQ performance
and specs with an analog look and feel. From its amazing 10Hz to 22kHz
frequency response, to its 113dB dynamic range and Advanced Feedback
Suppression (AFS?), dbx proprietary Type V? noise reduction
and PeakStopPlus? limiting, the iEQ-15 offers out of this world specifications
with a downto- earth price point. Sure to find a home in the studio, on tour and
with installed sound venues, the iEQ-15 is destined to take its rightful place in
the lineage of great dbx? signal processors that are the professional?s choice
in signal processing. With such pristine design and quality, the iEQ-15 offers
the maximum sonic flexibility in a straight forward interface and rock-solid construction.
? Advanced Feedback Suppression (AFS?)
? Type V? Noise Reduction
? PeakStopPlus? Limiting
? 2/3-octave Constant Q frequency bands
? Switchable boost/cut ranges of ±6 or ±15dB
? 18 dB per octave 40Hz low-cut filter
? ±12dB input gain range
? XLR, TRS and Euroblock Inputs and Outputs
? Internal Toroidal Transformer
? Frequency Response of 10Hz to 22kHz
? Dynamic range of greater than 113dB
? User Power Up Features
? Relay Bypass for Power Failure System Protection
| PRICE WITHOUT V.A.T.
BSS Opal FCS-966 Constant Q Graphic Eq
Graphic equalisers are found in just about every sound application, from room contouring to feedback control and general audio sweetening.
Traditionally, much general eq'ing takes place on the faders alone, but this restricts the use of the faders at each end of the scale for further precision eq work. So we provided the Opal FCS-966 with separate LF and HF contour filters which can change an overall sound balance without disturbing a detailed room or loudspeaker response.
These filters are very musical gentle boost and cut shelving filters which can be used to add (or remove) room effects that change with temperature, audience numbers or humidity.
All these effects can be easily made without disturbing the critical fader settings already made.
Constant Q Filters
The modern generation of graphic eq's
uses the Constant Q topology, pioneered by BSS Audio, which means that the filter width is constant whatever the fader gain setting.
Compared to the earlier 'gyrator' style of filters, Constant Q filters provide a smoother and more predictable interaction between adjacent faders and the resulting eq curve more closely resembles the actual fader positions.
More Gain Control Per Filter
Each eq fader has +/-15dB of adjustable gain, more than many competitive graphic eq's. The faders are long-throw 45mm types for precision control.
High Pass Filter
Also provided on the FCS-966 is a sweepable high-pass filter which can be used very effectively to restrict the low-energy output for better amplifier and loudspeaker performance. Stage monitors also benefit from the application of a high-pass filter to remove bass signals e.g. from vocal-only wedges.
Metering
BSS Audio believes in providing engineers with information, and the FCS-966's 8-segment led meter shows output level and warns of signal clipping within the eq. When the unit is switched to bypass, the meter will read the input level, allowing accurate matching of the 'dry' and equalised signals using the gain control.
Centre Bypass
When any eq fader is in its centre detent position, the filter is automatically bypassed, for optimum performance.
Input/Outputs
All the inputs and outputs of the FCS-966 are electronically balanced, with optional transformer balancing. To make installation of the FCS-966 easier, we've provided three differerent interface connectors: XLR-type, 1/4" TRS jack and Phoenix/Combicon screw terminals.
Relay Bypass
The EQ IN buttons switch the EQ path
into circuit. When switched out, or power fails, a high-quality relay switches the input signal directly to the output connectors.
Control Descriptions
Faders
30 EQ filter faders on ISO centres, each with nominal +/-15dB of gain. Positive centre-detent on 45mm long-throw precision faders.
HP Filter
Sweepable high pass filter, frequency adjustable from OUT (flat) up to 250Hz.
LF Contour
Smooth shelving filter, +/-6dB of gain at 50Hz
HF Contour
Smooth shelving filter, +/-6dB of gain at 14kHz.
GAIN
Used for overall unity gain adjustment. Adjustable from - infinity to +10dB.
CLIP
Triple-point clip detector that indicates red when the internal signal is clipping at any one of three critical points.
LED Meter
Shows output signal level (input signal when eq is bypassed) from -24dBu to +18dBu in 8 steps. |
Reviews
There are no reviews yet.