ASHLY PE3800-2X1900W-4Ω POWER AMPLIFIER

PE Series (Protea Enabled) amplifiers are high-power, high-efficiency, lightweight amplifiers
incorporating the latest in power and control technologies. Each amplifier can be controlled
and monitored through the built-in Ethernet port using Proteane Software?. Proteane gives
users access to many features, including: input attenuation, channel mute, channel polarity,
nput level, output voltage, output current, clipping, temperature, and power on/off.
Protea Enabled?
By adding Ashly?s Protea DSP technology and control to an amplifier, comprehensive and easy
to use audio system has been designed. With the introduction of the PE Series amplifiers,
Protea technology has been taken to the next level. Proteane Software allows you to setup, control
and monitor PE Series amplifiers using standard, inexpensive, readily-available Ethernet hardware.
Nothing proprietary here! Control anywhere from one to hundreds of amps, as well as your Protea
Series processors, on- or off-site with our intuitive and friendly Proteane Software.
There are six models of PE Series amplifiers, all of which share the same PE feature set, that
cover a wide range of power requirements from 400W to 1900W per channel @4 ohms. Each
utilizes a 2-stage high-efficiency switched mode power supply, which provides a high-power-to-weight
ratio. All are two rack units high and weigh less than 24lbs! All models will drive 2, 4 or 8 ohm loads.
Input connections are via XLR-1/4? Neutrik combo connectors and 6-pin Euroblock. XLR male
connectors are also provided for looping to additional amplifiers. Output connectors are locking
Neutrik Speakon (NL-4) on all models and 4 position screw terminal strip with safety cover on
models 800 and 1200.
Each PE Series amplifier provides on-board analog processing, including a selectable subsonic filter,
a selectable clip-limiter and an input-sensitivity selector, which can optimize the amplifier for load and
the many devices that can drive it. Plus, we?ve included an array of output current and temp indicators
to monitor various operating parameters. It?s easy to tell at a glance, for example, the status of the load
being driven (i.e. ?are my drivers working??). The PE Series also provides DC voltage control of the
calibrated Input attenuators, which makes it a snap to control volume from remote locations, and Remote
Power Turn-on/-off with sequential power on/off circuitry built right into the amplifier.
Option Cards
Need more? Proteane DSP Cards can be installed as needed. Their SHARC 32-bit/96kHz processor
enables 24-bit AD/DA, analog and digital (AES3) inputs. Each offers two additional processed output
channels to drive additional amplifier channels. Our current DSP library includes Graphic, Parametric,
Notch and Shelving Equalization, High-, Low- and All-Pass Filters (HPF/LPF/APF) with up to 48dB/
Octave slopes, Delay, Compressor/Limiter, Gate, Gain, Signal Generators (sinewave, white and pink
noise) and Matrix Routing.
Go Mobile!
Proteane mobile is a software application enabling you wireless control of PE-Series amplifiers and the
DSP-1 and DSP-2 Option Cards for the PE-Series amplifiers.
70 Volt
The PE-2400, PE-3000 and PE-3800 are capable of driving 70 Volt systems. Power specifications are:
PE-2400: 1200W per channel, PE-3000: 1500W per channel and PE-3800: 1700W per channel.

Ashly has long believed that the secret to great sound and reliability is intelligent design and meticulous
execution. Our PE Series takes that philosophy and multiplies it ten-fold. Optimized for cool operation,
modularity, ultimate compatibility and maximum performance, the PE Series is the amplifier line you?ve
been waiting for.
When your next project requires high performance amplifiers with superb sound, reliability, remote control
and more, Ashly Audio?s PE Series of remote-controlled power amplifiers have been designed to meet the
needs of both portable and installation applications.

General Specifications

Power Output:
Stereo Mono Bridge Parallel Mono
Model 8 ohms 4 ohms 2 ohms 8 ohms 4 ohms 2 ohms
3800  1100W  1900W  1500W  3800W  3000W  3800W
3000  900W    1500W  1500W  3000W  3000W 3000W
2400  700W    1200W  1500W  2400W  3000W 2400W
1800  500W    900W    1400W  1800W  2800W 1800W

Model  70 Volt
3800   1700W
3000   1500W
2400   1200W
Signal to Noise (20 Hz-20 kHz, unweighted):
800: >98dB
1200: >105dB
1800: >108dB
2400: >110dB
3000: >111dB
3800: >112 dB
Output Circuitry:
800: Bipolar, Class AB
1200: Bipolar, Class AB
1800: Bipolar, Class H
2400: Bipolar, Class H
3000: Bipolar, Class H
3800: Bipolar, Class H
Power Requirements (1/8 Power Pink Noise @ 4 Ohm):
800: 420W
1200: 640W
1800: 611W
2400: 790W
3000: 1010W
3800: 1220W
Current Requirements-Both Channels Driven
typ = 1/8 output, pink noise
Model idle 8 ohms 4 ohms Power Connector
typ max typ max
800 2.4A 6.6A 13.6A 9.4A 21.8A 15A Edison
1200 2.8A 8.6A 20.2A 13.6A 33.8A 20A Edison
1800 2.4A 8.4A 26.2A 13A 42A 20A Edison
2400 2.4A 10.4A 33A 15.8A 54A 20A Edison
3000 2.6A 12.4A 42A 19.6A 68A 30A Twistlock
3800 2.8A 14.6A 50A 22.6A 80A 30A Twistlock

All Models:
Voltage Gain: 26dB, 32dB or 1.5V sensitivity (selectable)
Distortion (SMPTE, typical) - 8 ohm load, 10dB below rated power:

Dynacord H 5000

 
The power amp H5000 is part of Dynacord´s new PowerH SERIES, which marks a milestone in the design and the production of high-performance power amplifiers. The innovative 3-stage Grounded Bridge Class H Topology with "floatingË switching power supply unit offers very high and stable output with extreme high efficiency on an extremely high performance level at minimum weight. PowerH amps are ideal for driving professional touring, high-end Concert-Sound and Pro-Sound applications.  

 
Dynacord H 5000 features:

    2x 1500 Watt / 8 Ohm
    2x 2500 Watt / 4 Ohm
    2x 3500 Watt / 2 Ohm
    Cooling: Front-to-Rear, 5-stage-fans
    Dimensions (WxHxD): 483 x 88.1 x 498 mm
    Weight: 14.5 kg
    Protections:
    Audio limiters
    High temperature
    DC
    HF
    Short Circuit
    Back-EMF
    Peak current limiters
    Inrush current limiters
    Turn-on delay
    Mains Circuit Breaker Protection
    Mains Overvoltage Protection

Power Output Level R-150 PLUS

STEREO
8ohm(T.H.D 0.05%)  50W+50W
4ohm(T.H.D 0.05%)  75W+75W

BRIDGED MONO
8ohm(T.H.D 0.05%)  50W
8ohm(T.H.D 0.5%)  170W

Frequency Response 20Hz- 20kHz, ±0.5dB

Convection Cooled

SoftStart Protection System

Balanced 10kΩ@0.775V Inputs

Model T5n
Product Type Power Amplifier
Output Power (W) 1kHz THD+N=1% (120V)
2Ω per channel 2500
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 5000
8Ω bridge 4400
Output Power (W) 1kHz 20mS burst (120V)
2Ω per channel 3400
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 6800
8Ω bridge 4400
SN ratio (20Hz-20kHz) 107dB
THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω
Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1%
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB
Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB
Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu
Damping factorRL=8Ω 1kHz 800
Voltage Gain Att.max 26dB
Maximum Input Voltage +24dBu
Input Impedence 20kΩ (balance) 10kΩ (unbalance)
Controls Specifications
Front Panel POWER switch(push on/push off) attenuator (31 position) x2
Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1
Connectors Specifications
Input XLR-3-31 type/ch; Euroblock connector (balance)/ch
Output SPEAKON/ch, 5way biding postx1
Date Port RJ45x2
Indicators Specifications
Power/Standby x1 (Green/Orange)
Remote x1 (Green)
Protection x1 (Red)
Temp x1 (Red) heatsink temp 85°C
Signal x2 (Green)
Mute x2 (Red)
Clip/Limit x2 (Red)
Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically
Cooling Variable-speed fan: x2
Power requirements 120V/60Hz
Weight 14.0 kg
Dimensions (W x H x D) 480 x 88 x 456mm (2U)

RMXa Series: Professional quality performance, incorporating road-proven QSC designs

• Compact size — up to 2500 watts in two rack spaces, or 5000 watts in three rack spaces
• High-current toroidal transformers, for greater 2-ohm power and low noise
• Independent user-defeatable clip limiters reduce distortion
• Selectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroom
• The 4000-watt RMX4050a operates on a standard 15 amp plug (120V) 
• Both the RMX4050a and the RMX5050a feature a dual mono, high-current power supply for increased reliability and performance
• The RMX4050a's particularly exceptional combination of cooling capacity and electrical efficiency provides robust thermal performance suitable for high continuous power in 2-ohm stereo or 4-ohm bridged applications.
• Balanced 1/4” (6.3 mm) TRS, XLR, and barrier strip inputs
• Touch-proof binding post and Neutrik Speakon® outputs
• Front mounted gain controls for easy access
• Signal and clip LED indicators for monitoring performance
• Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers
• 3-year warranty plus optional 3-year extended service contract