| Content |
When you add a Proteane DSP Option Card to your PE-Series amplifier, you have just
simplified system implementation for many applications in live sound, commercial sound
reinforcement and installations. Best of all, standard Ethernet protocol (auto or manual IP
configuring), a PC and Ashly?s easy to understand and navigate Proteane Software is
used to control everything.
Or, do it wireless! Proteane mobile is a software application enabling you wireless control
of PE-Series amplifiers and the DSP-1 and DSP-2 Option Cards for the PE-Series amplifiers.
Proteane DSP Option Cards use a SHARC 200MHz, 32-bit floating-point processor and
operates from 48 to 96kHz with a 24-bit AD/DA. Both the XLR and Euroblock versions offer
both analog and digital (AES3) inputs and two additional processed output channels to drive
additional amplifier channels. (One card will control two 2-channel amps!)
Proteane DSP cards have an extensive DSP library including: a full set of filter types for graphic,
parametric, notch and shelving equalization. Additionally, there are Bessel, Butterworth and
Linkwitz/Riley high and low pass crossover filters with slopes of up to 48dB/octave. For phase
correction, Ashly has included all pass filters as an option. Additional processing blocks include:
signal delay, compressor/limiter, gate, matrix mixer, signal generators (sinewave, white and pink
noise) and metering.
All DSP functions use a ?Click and Hot-Plug? user interface to place processor blocks in the signal
chain. This method allows you to select a processing block and place it wherever you need it in
your signal chain. The process is seamless and in real time, with no need to wait for your system
to recalculate or recompile its settings.
Remote control of the front panel attenuators, power standby/power down and recall of up to three
presets can be done using the contact closure terminals.
Installation is quite simple. Or, you can order your PE amplifier with the DSP Option Card factory
installed!
General Specifications Proteane DSP-1 and DSP-2
Input: Active Balanced, 10 kohms
Max Input Level: +20 dBu
Aux Outputs: Active Servo Balanced, 112 ohms
Max Output Level: +20 dBu
Frequency Response: 20 Hz-20kHz, ±0.25 dB
THD: 110 dB (20 Hz-20 kHz) unweighted
Aux Output Noise: | Digital stereo active crossover with 4 inputs and 8 outputs, incl. software .
- Flexible routing configurations for all standard mono and stereo output operating modes
- 4 analog inputs and 8 analog outputs (XLR)
- Active frequency filter types (Bessel, Butterworth and Linkwitz-Riley) with slopes up to 24 dB/octave split up the audio signal into different frequency bands
- Incl. software editor (for PC and Mac) for remote control via computer through USB interface: store, transfer, and manage your presets
- Up to 30 user presets storable in the device via software
- 5 menu languages selectable (German, English, French, Spanish, Dutch)
- Alphanumeric LCD screen with 2 lines of 16 characters each
- Input sensitivity digitally adjustable
- Inputs and outputs with 4-digit LED level meter as well as clip and limit LED indicator
- Mute switch with LED indicator per output
- 7-band parametric EQ per output
- Up to 7 ms signal delay adjustable for the outputs
- Output limiter with adjustable limits and automatic attack and release settings as overload protection for your amplifying system
- Switchable phase
- Lock function for prevents undesired changes to settings
- Rack installation, 1 U
- Windows XP, Vista, 7, 10 and Mac OS X 10.5.8 and better
- Digital signal processor
- The device can be connected via USB to the PC in connection with DXO Software
The firmware can be updated via the PC connection
- (19") 48.3 cm rack installation 1 U
| Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
| Power connection: |
Mains input via Coaxial power connector (M) power supply cord with AC adapter (provided) |
| Frequency range: |
10 - 22000 Hz |
| THD: |
<0,005 % at 1 kHz |
| DSP: |
Digital signal processor |
| Crossover frequency: |
20-20000 Hz |
| Impedance: |
Input 10 kOhm
Output 50 Ohm |
| Gain: |
Output: -50 dB to +12 dB |
| Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
| Delay: |
0 - 7 ms |
| Dynamic range: |
Input: 114 dB
Output: 110 dB |
| Sample rate: |
48 kHz |
| Connections: |
Input: line via 4 x 3-pin XLR
Output: line via 8 x 3-pin XLR |
| Max. level: |
Input: +22 dBu
Output: +9 dBu |
| USB port: |
Typ B |
| PC connect: |
DXO Software via USB, firmware can be updated |
| Housing design: |
(19") 48.3 cm rack installation 1 U |
| Dimensions: |
Width: 48,3 cm
Depth: 22,3 cm
Height: 4,45 cm |
| Weight: |
1,90 kg |
| The LD Systems X223 is a stereo 2 way / mono 3 way crossover in standard 19"/1U rack format. Its rugged construction, high quality and robust knobs as well as the integrated power unit are rarities in this price range. It provides a mono sub output, an adjustable crossover frequency for each channel, adjustable LF/HF and input gains, phase reverse controls, switchable 40 Hz High-Pass filters and symmetrical XLR In- and Outputs. With the LD Systems X223 you get a crossover fulfilling the professional standards and offering great quality and sound characteristics.
Product type
Signal Processors
Version
2-way stereo/3-way mono
Frequency response
20 - 20.000 Hz
Signal-to-noise ratio
> 93 dB
Total Harmonic Distortion (THD)
< 0.004 %
Crosstalk
< - 80 (20 - 20.000 Hz) dB
Max. input level
+21 (balanced or unbalanced) dBu
Max. output level
+21 (balanced or unbalanced) dBu
Input impedance (kOhms)
50000 kOhm
Output impedance
200 Ohm(s)
Controls
2 x crossover frequency low/high, 2 x crossover low/mid, 2 x high gain, 2 x highpass (40 Hz), 2 x input gain, 2 x low gain, 2x frequency switch x1/x10, 4 x inv switch, LF sum, Mono/stereo mode
Indicators
2 x clip, 2 x crossover x 10, 2 x highpass, 4 x inv., mono, stereo
Line input connectors
XLR
Line output connectors
XLR
Mains connector
IEC socket
Operating voltage
220 V AC - 240 V AC
| Overview
More sound to your amps and speakers
The secret to making speakers sound great lies with the crossover you use. With the dbx® 223xs Crossover you\'ll get great performance, ultra low-noise, rugged reliability and four decades of dbx knowledge and expertise in building the world\'s finest processors. The 223xs uses precision filters to separate the audio signal and direct the correct frequencies to your loudspeaker drivers. By directing only the specific frequency bands to each speaker driver the 223xs leaves your amplifiers free to use their full power on the usable signal eliminating distortion and giving your PA system a cleaner and better sound.
The dbx 223xs is a dual channel crossover with all the features you would expect from a professional product. It features Linkwitz-Riley 24dB per octave filters, independent output gain controls for level matching, output phase inversion, 40 Hz low cut filter, and optional mono summing of the low frequency (subwoofer) output. Everything in the design exudes great precision from the solid "click" controls to the high quality XLR inputs and outputs
Features
- XLR balanced ins and outs
- Mode switch for stereo 2-way or mono 3-way operation
- Low frequency summed (subwoofer) output
- x10 range switch on both channels
- 40Hz high pass (low cut) filter both channels
- Phase reverse switch on all outputs
- Individual level controls on all outputs
- 24dB per octave Linkwitz-Riley filters (the professional standard)
- Stereo/Mono status LEDs indicate the selected mode
- dbx® 2 year parts and labor as standard
- CSA NRTL/C approved
- CE compliant
Specifications
| Input Connectors |
XLR (pin 2 hot) |
| Input Type |
Electronically balanced/unbalanced, RF filtered |
| Input Impedance |
Balanced >50k ohm, unbalanced >25k ohm |
| Max Input |
>+22dBu balanced or unbalanced |
| CMRR |
>40dB, typically >55dB at 1kHz |
| Output Connectors |
XLR |
| Output Type |
Impedance-balanaced/unbalanced, RF filtered |
| Output Impedance |
Balanced 200 ohm, unbalanced 100 ohm |
| Max Output |
>+21dBu balanced/unbalanced into 2k ohms or greater |
| Bandwidth |
20Hz to 20kHz, +/-0.5dB |
| Frequency Response |
90 kHz, +0/-3 dB |
| Signal to Noise Ratio |
Ref: +4 dBu, 22 kHz measurement bandwidth |
| Signal-to-Noise (Stereo Mode) |
>94dB (Low Output), >91dB (High Output) |
| Signal-to-Noise (Mono Mode) |
>94dB (Low Output), >93dB (Mid Output), >91dB (High Output) |
| Dynamic Range |
> 106 dB, unweighted, any output |
| THD+Noise |
< 0.004% at +4 dBu, 1 kHz; < 0.04% at +20 dBu, 1 kHz |
| Interchannel Crosstalk |
< -80 dB, 20 Hz to 20 kHz |
| Crossover Frequencies (Stereo Mode) |
Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting) |
| Crossover Frequencies (Mono Mode) |
Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting) |
| Crossover Filter Type |
Linkwitz-Riley, 24 dB/octave, state-variable |
| Low cut Switch |
Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel. |
| Phase Invert Switch |
Inverts the phase at the output, one switch per output. |
| x1 / x10 Switch |
Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel. |
| Mode Switch |
Selects stereo/mono and 2/3-way operation |
| LF Sum Switch |
Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2ʼs low output phase invert LED to indicate that this output is not operational in the LF sum mode. |
| Indicators |
Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output) |
| Operating Voltage |
100 VAC 50/60 Hz; 120 VAC 60 Hz 230 VAC50 HZ |
| Operating Temperature |
32°F to 113°F (0°C to 45°C) |
| Power Consumption |
15W |
| Power Connector |
IEC receptacle |
| Dimensions |
1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm) |
| Unit Weight |
3.7 lbs. (1.7 kg) |
| Shipping Weight |
5.4 lbs. (2.5 kg) |
| More sound to your amps and speakers
The secret to making speakers sound great lies with the crossover you use. With the dbx® 234xs Crossover you'll get great performance, ultra low-noise, rugged reliability and four decades of dbx knowledge and expertise in building the world's finest processors. The 234xs uses precision filters to separate the audio signal and direct the correct frequencies to your loudspeaker drivers. By directing only the specific frequency bands to each speaker driver the 234xs leaves your amplifiers free to use their full power on the usable signal eliminating distortion and giving your PA system a cleaner and better sound.
The dbx 234xs is a dual channel crossover with all the features you would expect from a professional product. It features Linkwitz-Riley 24dB per octave filters, independent output gain controls for level matching, output phase inversion, 40 Hz low cut filter, and optional mono summing of the low frequency (subwoofer) output. Everything in the design exudes great precision from the solid "click" controls to the high quality XLR inputs and outputs.
XLR balanced ins and outs
Mode switches for mono 4-way or stereo 2-way/3-way operation
Low frequency summed (subwoofer) output
x10 range switch on both channels
40Hz high pass (low cut) filter both channels
Phase reverse switch on all outputs
Individual level controls on all outputs
24dB per octave Linkwitz-Riley filters (the professional standard)
Stereo/Mono status LEDs indicate the selected mode
dbx® 2 year parts and labor as standard
CSA NRTL/C approved
CE compliant
| Input Connectors |
XLR |
| Input Type |
Electronically balanced/unbalanced, RF filtered |
| Input Impedance |
Balanced >50k ohm, unbalanced >25k ohm |
| Max Input |
>+22dBu balanced or unbalanced |
| CMRR |
>40dB, typically >55dB at 1kHz |
| Output Connectors |
XLR |
| Output Type |
Impedance-balanaced/unbalanced, RF filtered |
| Output Impedance |
Balanced 200 ohm, unbalanced 100 ohm |
| Max Output |
>+21dBu balanced/unbalanced into 2k ohms or greater |
| Bandwidth |
20Hz to 20kHz, +/-0.5dB |
| Frequency Response |
90 kHz, +0/-3 dB |
| Signal to Noise Ratio |
Ref: +4 dBu, 22 kHz measurement bandwidth |
| Signal-to-Noise (Stereo Mode) |
>94dB (Low Output), >93dB (Mid Output), >90dB (High Output) |
| Signal-to-Noise (Mono Mode) |
>94dB (Low Output, Low/Mid Output); >92dB (High/Mid Output); >88dB (High Output) |
| Dynamic Range |
> 106 dB, unweighted, any output |
| THD+Noise |
| Interchannel Crosstalk |
| Crossover Frequencies (Stereo Mode) |
Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High 450Hz to 9.6kHz (x10 setting) |
| Crossover Frequencies (Mono Mode) |
Low/Low-Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low-Mid/High-Mid: 450 Hz to 9.6 kHz; High-Mid/High: 450 Hz to 9.6 kHz |
| Crossover Filter Type |
Linkwitz-Riley, 24 dB/octave, state-variable |
| Low cut Switch |
Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel. |
| Phase Invert Switch |
Inverts the phase at the output, one switch per output. |
| x1 / x10 Switch |
Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel. |
| Mode Switch |
Selects stereo/mono and 2/3/4-way operation |
| LF Sum Switch |
Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2ʼs low output phase invert LED to indicate that this output is not operational in the LF sum mode. |
| Indicators |
Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output) |
| Operating Voltage |
100-120 VAC 50/60Hz; 120 VAC 60Hz 230 VAC 50/60Hz |
| Operating Temperature |
32°F to 113°F (0°C to 45°C) |
| Power Consumption |
15W |
| Power Connector |
IEC receptacle |
| Dimensions |
1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm) |
| Unit Weight |
4.0 lbs. (1.8 kg) |
| Shipping Weight |
5.8 lbs. (2.6 kg) |
|
Full-featured Speaker Processing in a 1U Space
Speaker processing can be a complicated business requiring a substantial array of equipment, but the Yamaha SP2060 offers everything you need in a single rack space. This innovative 24-bit, 96-kHz digital speaker processor delivers excellent sound quality, an impressive variety of processing functions — gain, delay, PEQ, comp, crossover, limiter, and an all-pass filter for phase adjustment — and intuitive programming from Yamaha's DME Designer application running on a personal computer. It has two analog inputs and six analog outputs, plus two AES/EBU format digital inputs for connectivity with a broad range of systems. And if you use Yamaha Installation Series Speakers, all you need to do is select one of the many optimized presets provided for great sound with minimum measurement and setup time. The SP2060 is a compact, portable 1U unit that is ideal for live sound or installations.
| Sampling Frequency | Internal Clock | 96kHz | | External Clock | Normal Rate | 44.1, 48kHz (±0.1%) | | Double Rate | 88.2, 96kHz (±0.1%) | | Signal Delay | 761µsec Input to Output, fs = 96kHz | | Frequency Response | 20Hz -40kHz (TYP 0dB, MAX +0.5dB, MIN -1.0dB), fs=96kHz, RL=600ohms | | Total Harmonic Distortion | 0.007% (+22dBu@1 kHz),
0.05% (+4dBµ@20 Hz - 40kHz)
fs=96kHz, RL=600ohms;
measured with 18dB/octave filter @80kHz | | Hum & Noise | TYP -82dBu,
fs=96kHz, RL=600ohms, Rs=150 ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞ dB/octave attenuation. | | Dynamic Range | 106dB AD+DA
fs=96kHz, RL=600ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞dB/octave attenuation. | | Crosstalk @1kHz | -80dB INPUT to Output
fs=96kHz, measured with 18dB/octave filter @80kHz | | Power Consumption | 30W | | Dimensions (W x H x D) | 480 x 44x 360.2mm | | Net Weight | 4.2kg |
|
Reviews
There are no reviews yet.