| Content |
The ADX20iP is applicable for professional stage and studio applications. This mic is primarily used for miking most reed and brass instruments.
The ADX20iP has a uniformly controlled cardioid polar pattern, which provides excellent isolation and feedback control on stage with natural sound reproduction at very close distances.
The ADX20iP is lightweight, compact and simple to use. Included with the ADX20iP is a gooseneck clip with spring tension for easy mounting to the bell of an instrument.
Model Variation: ADX20i - for use with RAD360 wireless system. No power adapter is included with this model.
The ADX20i requires phantom power of 9-52 V.
| Type | Pre-polarized Condenser |
|---|
| Polar Pattern | Cardioid, Hypercardioid | | Frequency Response | 40Hz - 20kHz | | Impedance | 250 Ohms | | Sensitivity | 6 mV/Pa @1k (C) / 5.6 mV/Pa @1k (HC) |
| The unidirectional dynamic microphone DAP PL-07 is ideal for live sound reinforcement and clear recording of Brass, Saxophone, Harmonica, Snare, Tom, Congas and Guitar-Bass Amps.
Technical Info
Type: Dynamic, Moving coil.
Freq.Resp.: 40 to 16.500 Hz.
Polar Pattern: Cardioid
Sensitivity (1000Hz): 1,7 mV/Pa*
(*1 Pa = 94 dB SPL)
Max SPL: 137dB
Impedance: 600 Ohm
Power supply: none
Connector: 3p. XLR male-type).
Net. Weight: 245 g
Dimensions: (Ø 32 mm x L 157 mm)
Accessories: 6 mtr balanced cable
with XLR plugs |
The super-cardioid e 609 instrument microphone has been specially developed for miking guitar cabs face on and extremely close to the signal source.
Pick-up pattern : Super-cardioid
Frequency response : 40.....15000 Hz
Sensitivity in free field, no load (1kHz) : 1,5 mV/Pa
Nominal impedance : 350 Ohm
Min. terminating impedance : 1000 Ohm
Dimensions : 55 x 34 x 134 mm
Weight : 140 g
|
The Shure KSM137 is an end-address condenser microphone with a cardioid polar pattern. Designed for studio use, yet rugged enough for live applications, the KSM137 can withstand extremely high sound pressure levels (SPL). Its low self-noise and extended frequency response make it ideal for recording musical instruments.
Features
- A highly consistent cardioid polar pattern
- Ultra-thin, 2.5 micron, 24 karat gold-layered, low mass Mylar? diaphragm for superior transient response
- Class A, discrete, transformerless preamplifier for transparency, extremely fast transient response, no crossover distortion, and minimal harmonic and intermodulation distortion
- Premium electronic components, including gold-plated internal and external connectors
- Subsonic filter eliminates low frequency rumble (less than 17 Hz) caused by mechanical vibration
- Switchable 15 dB pad for handling extremely high sound pressure levels (SPLs)
- Three-position switchable pad (0 dB, 15 dB, and 25 dB) for handling extremely high sound pressure levels (SPLs)
- Three-position switchable low-frequency filter reduces background noise and counteracts proximity effect
Performance Characteristics
- Extended frequency response
- Low self noise
- Exceptional reproduction of low-frequency sounds
- Can withstand high sound pressure levels (SPL)
- High output level
- No crossover distortion
- Uniform polar response
- Superior common mode rejection and suppression of radio frequency interference
APPLICATIONS
Some typical applications for the KSM137 are listed below. Microphone use, however, is a matter of personal taste. The KSM137 may be used for a variety of applications other than those listed.
- Acoustic instruments -- such as piano, guitar, drums, percussion, strings
- Wind instruments -- brass and woodwind
- Low frequency instruments -- such as double bass, electric bass, kick drum
- Overhead miking -- drums or percussion
- Ensembles -- choral or orchestral
- Room ambiance pick-up -- guitar amplifier or drums
Both the acoustic environment and microphone placement strongly affect the sound obtained from miking a source. You may need to experiment with microphone placement and room treatments to achieve the best overall sound for each application.
Suggested Applications
Acoustic Guitar
Acoustic Bass
Cymbals
Brass/Woodwinds
Orchestra
Ensemble Vocals
Piano
Strings
Room Ambience
Live Recording
|
The supercardioid e 906 instrument microphone was especially designed for
guitar amplifiers, but it is also an excellent choice for percussion and brass
instruments.
Features
Lively, full sound
Very fast attack
Flat shape of microphone body perfect for guitar amps
Three adjustable sound characteristics (bright, normal, smooth)
Hum compensating coil
Rugged metal body
Delivery Includes
e 906 microphone
MZQ 100 clamp
Pouch
User manual
Technical Data
Pick-up pattern supercardioid
Frequency response 40...18000 Hz
Sensitivity in free field, no load (1kHz) 2,2 mV/Pa
Nominal impedance 350 Ohm
Min. terminating impedance 1000 Ohm
Dimensions 55 x 34 x 134 mm
Weight 140 g
|
NEW Wider mounting base capable of accommodating a larger range of microphone stands. Even works with the LP Claw.
Specifically engineered for drum and instrument applications, the Beta 56A's compact, pivoting design makes it the ideal choice for these applications.
Its extremely uniform supercardioid pickup pattern provides high gain before feedback and excellent rejection of unwanted noise. A built-in dynamic locking stand adapter with an integral XLR connector simplifies installation. The stand adapter keeps the microphone securely in place, even if it is struck by a drumstick. Typical Beta 56A applications include close miking of tom-toms and other percussion instruments, as well as guitar amplifiers, brass instruments, and woodwinds.
- Built-in stand adapter with dynamic locking system and XLR connector simplifies setup and provides greater flexibility
- Uniform supercardioid pattern for high gain-before-feedback and superior rejection of off-axis sound
- Compact design reduces stage clutters
- Hardened steel mesh grille resists wear and abuse
- Neodymium magnet for high signal-to-noise ratio output
- Advanced pneumatic shock mount system that minimizes transmission of mechanical noise and vibration
- Frequency response: 50 to 16,000 Hz
|
Reviews
There are no reviews yet.