Content |
Beyerdynamic Headphones DT 100
The DT 100 headphone is widely used in audio recording and monitoring applications in studios worldwide.
It is also intended for use in ENG/EFP field work, on-air commentary and in any other situation which needs to address the challenges of today's digital and technological advances. The DT 100 offers a high degree of comfort and can be worn for hours without listener fatigue. The soft ear cushions effectively seal out ambient noise yet apply minimal pressure against the ear.
Specifications:-
* Transducer type Dynamic
* Operating principle Closed
* Frequency response 30 - 20,000 Hz
* Nominal impedance acc. to IEC 60268-7 16 ? ± 10% per cartridge
* Nominal SPL acc. to IEC 60268-7 94 dB
* Nominal THD acc. to IEC 60268-7
* Power handling capacity acc. to IEC 60268-7 1000 mW
* Sound coupling to the ear Circumaural
* Ambient noise isolation 20 dB (A)
* Average pressure on ear acc. to IEC 60268-7 4.5 N
* Weight without cable 350 g
| The ATH-M20x professional monitor headphones are a great introduction to the critically acclaimed M-Series line. Modern design and high-quality materials combine to deliver a comfortable listening experience, with enhanced audio and effective isolation. An excellent choice for tracking and mixing.
- Advanced build quality and engineering
- 40 mm drivers with rare earth magnets and copper-clad aluminum wire voice coils
- Tuned for enhanced low-frequency performance
- Circumaural design contours around the ears for excellent sound isolation in loud environments
- Convenient single-side cable exit
Specifications
- Type: Closed-back dynamic
- Driver Diameter: 40 mm
- Magnet: Neodymium
- Voice Coil: Copper-clad aluminum wire
- Frequency Response: 15 - 20,000 Hz
- Maximum Input Power: 700 mW at 1 kHz
- Sensitivity: 96 dB
- Impedance: 47 ohms
- Weight: 190 g (6.7 oz), without cable and connector
- Cable: 3.0 m (9.8'), straight, left-side exit
- Accessory Included: 6.3 mm (1/4“) snap-on adapter
| Beyerdynamic DT 150
The DT 150 is a dynamic studio headphone for use in broadcasting, film and recording studios
and other audio monitoring applications where size, comfort and performance are primarily requirements.
Due to its closed design it features excellent ambient noise isolation for reference monitoring.
- Transducer type: Dynamic
- Operating principle: Closed
- Frequency response: 5 - 30,000 Hz
- Nominal impedance: 250 Ω
- Nominal SPL: 97 dB
- Power handling capacity: 100 mW
- Sound coupling to the ear: Circumaural
- Headband pressure: 4.5 N
- Ambient noise attenuation: approx. 20 dBA
- Weight (without cable): 250 g
| DT770 Closed headphone for drummers and monitoring purposes (FOH), with extreme isolation against ambient noise.
The dynamic, closed DT 770 M has especially been designed for drummers and FOH monitoring. The strengthened headband and the softskin ear pads provide an excellent isolation against ambient noise. The single sided straight cable allows a volume control directly at the headphone.
▲ Closed headphone
▲ Excellent ambient noise attenuation (35 dBA)
▲ Superb sound quality with high sound pressure level (105 dB)
▲ Extended frequency range
▲ Single-sided cable with volume control
▲ Robust, easy serviceable construction as all parts are replaceable
▲ Excellent comfort for long-term wearing, softskin ear pads
▲ Secure and comfortable fit due to rugged, adjustable headband construction with soft padding
▲ Single-sided cable
▲ Supplied in a carrying case (nylon)
Transmission type |
|
Wired |
Headphone design (operating principle) |
|
Closed |
Headphone impedance |
|
80 ohms |
Headphone frequency response
The frequency response specifies the highest and lowest frequencies reproduced by the acoustic transducer of the headphones. |
|
5 - 30.000 Hz |
Nominal sound pressure level
The (nominal) sound pressure level is the pressure in pascals (Pa) with which the air and the eardrum are caused to vibrate, better known as the volume. The sound pressure level is therefore a measure of the volume of a set of headphones under standardized conditions. However, it says nothing about whether the distortion is low and the sound is good at such a high volume. |
|
105 dB |
Construction |
|
Circumaural (around the ear) |
Cable & plug |
|
Straight connecting cable with mini-jack plug (3.5 mm) & ¼" adapter (6.35 mm) |
Net weight without packaging |
|
300 g |
|
The SRH440 Professional Studio Headphones from Shure provide exceptional sound reproduction and comfort.
Optimized for home and studio recording, SRH440 headphones reproduce accurate audio across an extended range.
Impedance, power handling and sensitivity are all calibrated for professional audio devices such as DJ mixers, mixing consoles, and headphone amplifier. Includes carrying bag and threaded 1/4" (6.3mm) gold plated adapter.
Enhanced frequency response delivers accurate audio across an extended range
Impedance and power handling optimized for perfomance with professional audio devices
Adjustable headband and collapsible construction provide comfort and portability
Bayonet clip securely locks detachable cable into ear cup
Sensitivity
105 dB
Maximum Input Power
500 mW
Frequency Response
10 Hz - 22 kHz
Weight
9.6 oz (272 g)
Cable Length
3 meters (9.84 ft)
Cable Style
Detachable coiled oxygen-free copper
Plug
Gold-plated 1/8" (3.5 mm) stereo mini jack
|
Operating Principle: Closed
Transmission Type: Wired
Earpad material: Protein leatherette cover, memory foam filling
Nominal Impedance Headphones: 32 ohms
weight headphones without cable: 360 g
Headphone frequency response: 5 - 50,000 Hz
Nominal sound pressure level: 100 dB (1mW)
Sound coupling to the ear: Circumaural (around the ear)
Cable & Plug: 1.40 straight cable (double-sided), OCC 7N copper, textile braided, 3.5 mm jack plug with 6.35 mm jack adapter
|
Reviews
There are no reviews yet.