BITTNER AUDIO XV 1000-2x500W-100V POWER AMPLIFIER

1,905.16 incl. GR VAT

Available on backorder

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
XB Series – Intelligent Power Power Without Compromises.The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality.Sequential power on, alive contacts and incorporated ground fault detection – the XV is the solution under all conditions. Without the need for […]

 

Read more

XB Series – Intelligent Power

Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection –
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XV 1000: 2×500 W/100 V
Class:  AB
Frequency Response: 20 Hz – 20 kHz (0 / -0.3 dB)
THD:  < 0.07%
Signal-to-Noise Ratio:  < 101 dB
Channel Seperation:  > 70 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Cooling:  2 to 3 fans (temp. reg. variable speed)
Weight:  33 kg
Dimensions:  2 RU / 483 x 88 x 382 mm (19″ x 3.5″ x 15“)

Weight 33.00 kg

Reviews

There are no reviews yet.

Be the first to review “BITTNER AUDIO XV 1000-2x500W-100V POWER AMPLIFIER”

Your email address will not be published. Required fields are marked *

Quick Comparison

BITTNER AUDIO XV 1000-2x500W-100V POWER AMPLIFIER removeCrown CDI-2000 2x800W-4Ω Power Amplifier removeTOA CA-130 60W Mobile Amplifier removeTOA A-2120 120 Watt Amplifier removeINTER-M PAM-520 ZONE AMPLIFIER 240W removeBITTNER AUDIO XV600-2x300W-100V POWER AMPLIFIER remove
NameBITTNER AUDIO XV 1000-2x500W-100V POWER AMPLIFIER removeCrown CDI-2000 2x800W-4Ω Power Amplifier removeTOA CA-130 60W Mobile Amplifier removeTOA A-2120 120 Watt Amplifier removeINTER-M PAM-520 ZONE AMPLIFIER 240W removeBITTNER AUDIO XV600-2x300W-100V POWER AMPLIFIER remove
Image
SKUBIT-0003CDI-2000CA 130A-2120PAM-520XV600
Rating
Price 1,905.16 incl. GR VAT 1,688.00 incl. GR VAT 160.00 incl. GR VAT 348.00 incl. GR VAT 707.00 incl. GR VAT 1,277.20 incl. GR VAT
Stock

Available on backorder

Available on backorder

Available on backorder

In stock

In stock

Available on backorder

AvailabilityAvailable on backorderAvailable on backorderAvailable on backorderIn stockIn stockAvailable on backorder
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

XB Series - Intelligent Power

Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XV 1000: 2x500 W/100 V
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.07%
Signal-to-Noise Ratio:  < 101 dB
Channel Seperation:  > 70 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Cooling:  2 to 3 fans (temp. reg. variable speed)
Weight:  33 kg
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)

Crown CDi 2000 2x800W-4Ω Power Amplifier

The Crown? CDi 2000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply.
The outputs shall be usable as dual or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker. Dual connectors shall work with 2-8 ohm or
70V loads. Bridge-mono connectors shall work with 4-8 ohm or 140V loads.
HiQnet USB Connector: Type B, connects to a USB port on a PC.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Dual (per channel): 1,000W with 1% THD, 4 ohm Dual
(per channel): 800W, 8 ohm Dual (per channel) 475W, 4 ohm Bridge-Mono:
2,000W with 1% THD, 8 ohm Bridge-Mono: 1,600W, 70V Dual (per channel):
800W.
Voltage Gain at 1kHz, 8 ohm rated output: 32.9 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Dual
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity: 1.4V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB (A
weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.9A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave and Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB
bandpass gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 20 presets. 19 are user-defi nable.
Protection shall include the following:
CDi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg).
The amplifier shall be designated the Crown CDi 2000.

  • Easy installation in practically any 12V battery equipped car.
  • Compact, rugged construction and front panel controls.
  • Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
  • Unidirectional dynamic microphone with talk switch.

Specification
Power Source Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used)
Power Consumption 4.4A or less at rated power output.
Output Power Rated 30W, max. 60W
Output Impedance 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections.
Distortion Less than 5% (at 1kHz rated output)
Frequency Response 100 ~ 10,000Hz
Input Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack
Dimensions (W x H x D): 178 x 50 x 144mm (mounting device excluded)
Weight 1.1 kg
Finish Front panel; ABS resin, Black
Case; Zinc plated steel sheet
Accessory Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (8A) ... 1
Connection cord ... 1 set
Accessory Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa)

High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.

 

Specification
Power Source 220 - 240V AC or 24V DC
Rated Output 120W
Power Consumption 124W (EN60065), 260W(AC operation at rated output, 8A (DC operation at rated output)
Frequency Response 50 - 20,000Hz (+/- 3 dB)
Distortion Under 1% at 1kHz,1/3 rated power
Input MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1)
Output SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:83W (100V)
LOW IMPEDANCE: 4Ω (22V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack
Phnatom Powe DC + 21V (MIC 1)
S/N Ratio Over 60dB
Tone Control Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz
Muting MIC1: Mutes other signals by 0 - 30 dB attenuation
Indicator Power signal, peak
Finish Panel: ABS resin, black/Case: Steel plate, black
Dimensions 420 (W) x 100.9 (H) x 360.3 (D) mm
Weight 10kg

 

- SPEAKER SELECT(5ZONE SPEAKER OUTPUT)

Six speaker select switches enable you to select any combination of up to five speakers.

- SELECTABLE PRIORITY MUTING

Switchable audio signal priority for MIC Channels 1, siren, Chime and Telephone input over other input sources.

- MONITOR SPEAKER

You can monitor output signal by using the monitor speaker, and can control the monitor level on front panel by 3 step lever switch.

- ANNOUNCEMENT CHIME

Convenient four-tone chime for use with announcements.

- REMOTE CONTROL INPUT

Individual speaker zones can be selected and chime can be operated by wired remote control.

- EM(EMERGENCY)

When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted.

- REMOTE POWER

You can turn on/off amplifier by remote control.

- INDIVIDUAL INPUT GAIN CONTROLS

Rear-panel gain controls for each input channel for total control of individual levels.

- MODULAR DESIGN

Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-510/520ʼs audio capabilities.

ACCESSORIES

One detachable AC power cord is provided for use with this product.

PAM-510

PAM-520

Amplifier Section

(Amp In@1kHz,

4Ω Load Output)

Rated Output Power (THD 1%)

120W(RMS)

240W(RMS)

Speaker Zone 1~5 Output

25W MAX

50W MAX

Input Sensitivity/Impedance

1V/20kΩ

S/N

Better than 85dB

Frequency Response

(at 1kHz Half Power Output, ±3dB)

80Hz~18kHz

Mic Input Section

(Mic 1~4 In@1kHz,

Preamp Out)

Input Sensitivity/Impedance

–60dBV/600Ω

S/N

Better than 55dB

Frequency Response (±3dB)

120Hz~10kHz

Tone Control

(Bass:100Hz,Treble:10kHz)

±12dB

Phantom Power

+24VDC

Line Input Section

(Line 1~2 In@1kHz,

Preamp Out)

Input Sensitivity/Impedance

–30dBV/10kΩ

S/N

Better than 65dB

Frequency Response (±3dB)

80Hz~15kHz

Tone Control

(Bass:100Hz,Treble:10kHz)

±12dB

Remote Amp Section

(Remote In@1kHz,

Preamp Out)

Mic Input Sensitivity/Impedance

–60dBV/600Ω

S/N

Better than 55dB

Frequency Response (±3dB)

120Hz~10kHz

Tel In Section

(Tel In@1kHz,

Preamp Out)

Input Sensitivity/Impedance

0.3V/600Ω(USA/Canada)

0.775V/600Ω(EC & Associated)

S/N

Better than 65dB

Frequency Response (±3dB)

330Hz~3kHz

Pre Amp Out(Mic 1~4, Line 1~2, Tel In, Remote In)

0dBV/600Ω

T.H.D

Less than 0.5%

Record Out

–10dBV/3kΩ

Operating Temperature

–10°C~40°C

Power Source

100–120VAC or 220–240VAC; 50/60Hz, 24VDC

Power Consumption (1/8 POWER)

180W

320W

Weight

17kg/37.6lb

19kg/42lb

Dimensions

482(W) x 132(H) x 398(D)mm

19(W) x 5.2(H) x 15.7(D)in

※ Specifications and design subject to change without notice.

XB Series - Intelligent Power

Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XV 600:  2x 300 W / 100 V
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.07%
Signal-to-Noise Ratio:  < 101 dB
Channel Seperation:  > 70 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Cooling:  2 to 3 fans (temp. reg. variable speed)
Weight:  19 kg
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)

Weight33.00 kg10.00 kg1.10 kg10.00 kg19.00 kg19.00 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 33.00 kg
Weight 10.00 kg
Weight 1.10 kg
Weight 10.00 kg
Weight 19.00 kg
Weight 19.00 kg