CREST AUDIO CPX 2600 2X900 W AMPLIFIER

The CPX-2600 is an affordable amplifier geared towards MI and DJ markets. A tradition
of great sound quality, flexibility and reliability is carried over into the Crest Performance
series. Industry standard connectors and features make the CPX-2600 a great back bone
for mobile sound systems, project studios, and many other applications. Musicians will
also find the CPX-2600 as the power amp of choice.
If you need maximum performance on a tight budget, you owe it to yourself to get your
hands on a CPX-2600 from Crest Performance.

Features Of The Crest CPX-2600
GCL Gain Comparator Limiting system with rear panel defeat switch
Built-in crossover
150Hz, 24 dB per octave Linkwitz-Riley filter, tuned for subs
Individual in/out switches for Channels A and B
1/4" daisy chain outputs
Input connectors: Barrier strip, Female XLR 1/4" TRS
Rear panel polarity switches for XLRs, Pin 2 hot
Outputs connectors: Speakons for Ch A and B and Bridged mono,
Binding posts for Bridge mode
Mode selector switch for stereo and bridged-mono operation
Two-speed DC fan

Specifications:
Power Rating 8 Ohm Stereo: 550 Watts
Power Rating 4 Ohm Stereo: 900 Watts
Power Rating 2 Ohm Stereo: 1100 Watts
Power Rating 8 Ohm Bridge: 1550 Watts
Power Rating 4 Ohm Bridge: 2200 Watts
Distortion:

The new LD Premium Audio CLASS-H SMPS amplifiers distils all the features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment. In the LD Premium amps, you'll find four 2-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.

• Model Name: SP1K8
• Output Power 1 kHz, 500
• Crosstalk (20 Hz - 20 kHz): > 75 dB
• Voltage Gain (selectable): 26/32/38 dB
• Input Sensitivity: 2.6/1.3/0.6 V
• Protection: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, ICLTM, PMSTM, SSPTM
• Controls: On / Off Switch, Volume, Voltage Gain, Dual / Link Switchable, Bridge Mode Configuration Switch
• Indicators: Signal, Temperature, ICL (Inteligent Clip Limiting), PMS (Power Management System)
• Connectors:
  • Input: 2 x XLR
  • Line Output: 2 x XLR
  • Speaker Output: 2 x Speakon
• Power Supply: 230 V - 50 Hz
• Dimensions (WxHxD): 483 × 88.9 × 310 mm / 19 × 3.5 ×12.2 inches

Crown DSi 2000 2x800W-4Ω Power Amplifier

The Crown? DSi 2000 power amplifier shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifier and the DSi-8M System Monitor.

The outputs shall be usable as stereo or bridged-mono modes of operation.

The bridged-mono mode shall bridge the outputs to provide increased output voltage.

Front panel controls and indicators shall include the following:

Level: Detented rotary level control, one per channel.

Power Switch: On/off switch applies AC power to the amplifi er.

Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout.

LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing.

Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input.

?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below clip.

?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB below clip.

Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.

Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.

Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.

Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power.

Rear panel controls and connectors shall include the following:

AC Line Connector: NEMA 5-15P (15A).

Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal.

Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker.

HiQnet USB Connector: Type B, connects to a HiQnet network.

HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.

The amplifier shall have the following specifications:

Output Power: 2 ohm Stereo (per channel): 1,000W with 1% THD, 4 ohm

Stereo (per channel): 800W with 0.5% THD, 8 ohm Stereo (per channel) 475W

with 0.5% THD, 4 ohm Bridge-Mono: 2,000W with 1% THD, 8 ohm Bridge-

Mono: 1,600W with 0.5% THD.

Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.

Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.

Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo

mode, 4 to 16 ohms in Bridge-Mono mode.

Sensitivity at 8 ohm rated output: 3.09V.

Sensitivity at 4 ohm rated output: 2.84V.

Sensitivity at 2 ohm rated output: 2.24V.

Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB

(A weighted).

Damping Factor: Better than 500 from 20 Hz to 500 Hz.

Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.

Input Stage: Input is electronically balanced and employs precision 1% resistors.

Input Impedance (nominal): 20 k ohms, balanced;10 k ohms,unbalanced.

Maximum Input Signal: +22 dBu typical.

XR Series - Intelligent Power
New Horizons.

A lightweight with enormous power output. Combined with digital signal processing.
That's what we call flexibility! Locally controlled or completely networked.
No matter what the requirements are.
The integrated powerful digital signal processor (DSP) and controller allows
for a troublefree and easy adjustment to any acoustical environment.
Wear-free digital potentiometers, sequential remote power on,
alive contacts for easy supervision, computer controlled monitoring -
 its enless list of useful feature make it the right choice for any installation.
XR - the new definition of Intelligent Power

High Tech SMT Design
Digital Signal Processor
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX / Speakon
High-End Switched Power Supply with Power Factor Correction (not XR4000)
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed low noise fans
Digital wear-free Volume Controls (can be operated manually)
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Paging Input
Monitor Output
SXL Dataport
Perfect Weight-to-Power ratio
3 Years Warranty

Technical Data:
 
Class:  H
Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.02%
Signal-to-Noise Ratio:  < -106 dB
Channel Seperation:  > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  750 to 1200 @ 4 Ohm
Cooling:  4 Fans (temp. reg. variable speed)
Weight:  8 to 10 kg (18 to 22 lbs)
Dimensions:  2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“)

A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange, and superbly defined highs. They also deliver fast response and exceptional stability even in the face of serious power supply limitations. Refinements throughout this expanded five-model lineup make these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 500 Watt / 8Ω RMS, 2 x 800 Watt / 4Ω RMS, 1600 Watt / 8Ω bridge RMS. Weight: 12,5 Kg.

• Output power: 750W @ 4 Ohms stereo, 500W @ 8 Ohms stereo
• High-current toroidal transformers for greater power and low noise
• Independent user-defeatable peak limiters reduce distortion
• Selectable High-Pass filter at 30Hz or 50Hz
• XLR and 1/4\' TRS input jacks
• Binding post and Speakon?-type outputs
• Front mounted gain controls for easy access
• Signal and Peak LED indicators to monitor performance
• Short circuit, thermal, subsonic, RF protection, output DC offset
• Power on/off muting