Content |
CA 6
The CA6 professional power amplifier is designed to achieve unsurpassed sonic performance and long-term reliability--even when operating under extreme stress--in touring or fixed installation applications. Application The CA? series provides tremendous value in proven amplifier technology.CAs form the backbone of discriminating rental systems and high-power club installations worldwide. Auditoriums, churches, regional tour sound companies and mobile DJs are all ideal candidates for the CA Series? combination of value and sonic quality. Design Focus The CA Series design provides economical access to the premium sound quality of the Crest Audio Pro Series. Professional power-handling capabilities and exceptional low-end response make this amplifier an ideal choice for installations and touring applications that demand the finest audio quality.
FEATURES: 8 Ohm Stereo - 400 W 4 Ohm Stereo - 600 W 2 Ohm Stereo - 750 W 8 Ohm Bridged - 1200 W 4 Ohm Bridged - 1500 W Legendary over-built power supply Toroidal power transformer Latest generation of high-speed, wide-bandwidth output devices Twin-tunnel cooling with back-to-front air flow Dual, rear-mounted, continuously variable-speed fans Balanced male and female XLR inputs with switch-configurable XLR polarity and sensitivity selection Speakon? or five-way binding post output connectors (market dependent) Stereo, parallel, bridged-mono mode selector switch Ground-lift switch Front panel circuit-breaker switch Recessed, stepped attenuators SIGNAL present/active, PROTECT, and ACL LED's Modular construction Powder-coated steel chassis Five-year warranty Dimensions 19" W x 3.5" H x 18" D (483 mm x 89 mm x 458 mm) Weight 44 lbs. (20 kg)
|
- Signal to Noise (20 Hz - 20 kHz): 100 dB - Input Sensitivity: 1.2 Vrms - Voltage Gain (8 Ohms): 34.4 dB - Output Circuitry: 2-tier Class H - Power Requirements: 6A - Frequency Response: 20 Hz - 20 kHz, +0, 1 dB - Dynamic Headroom (4 Ohms): 2 dB - Damping Factor: 100 - Input Impedance: Greater than 20k (balanced) - Maximum Input Level: +24 dB (16 Vrms) - Input Connectors (each channel): 3-pin XLR and 1/4-inch TRS, balanced, parallel Phono, unbalanced - Output Connectors (each channel): Speakon, 1/4-inch, Binding Posts - Amplifier and Load Protection: Short circuit, open circuit, thermal, RF protection Load protected against DC faults - Rear Panel Controls: Full Range / Crossover switch - Dimensions (H x W x D): 3.5 x 19 x 10.1 inches (89 mm x 483 mm x 257 mm) - Weight: 26 lbs (12 kg) Front Panel Controls and Indicators: - Gain controls, 21 detents - Red Clip LEDs, proportional, 0.1% THD threshold - Green Signal LEDs, threshold -35 dB - Blue Power LED, AC on Stereo Mode: - 8 Ohms / both channels driven: 500 Watts - 8 Ohms / single channel driven: 600 Watts - 4 Ohms / both channels driven: 700 Watts - 4 Ohms / single channel driven: 850 Watts Distortion: - 8 Ohms: less than 0.05% - 4 Ohms: less than 0.1% Dimensions and Weight in Packaging Shipping Weight: 31 lbs Shipping Dimensions: 24 x 15 x 7 in
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the face
of serious power supply limitations. Refinements throughout this expanded five-model lineup make
these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications.
Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 400 Watt / 8Ω RMS, 2 x 700 Watt / 4Ω RMS,
1400 Watt / 8Ω bridge RMS. Weight: 13 Kg. |
BASIC Series - Intelligent Power
BASIC - that's meeting the tightest budgets and professional requirements in reliability, flexibility and sound. Alone or in combination with the other products of the Bittner portfolio. The consequent realisation of the Bittner quality standards indicates once more our understanding of the contracting business. It underlines our philosophy that cost consciousness has nothing to do with giving up standards. Compromise is a word unknown to Bittner Audio! The incorporation of detent potentiometers, clip limiter, protection circuits for any imaginable situation, as well as a first-class production process using only highest-quality components made the BASIC series the choice of most contractors.
Certainly more than basic!
High Tech SMT design Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay XLR Inputs Speakon and Binding Posts Clip Limiter Toroidal transformers LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed, low noise fans Detent potentiometers Stereo / Bridged / Parallel Mode Ground Lift Robust Steel Chassis 3 Year Warranty
TECHNICAL DATA: Basic 1200: 2x 600 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.03% Signal-to-Noise Ratio: < -102 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: > 400 @ 4 Ohm Cooling: 2x Fan (temp. reg. variable speed) Weight: 15 kg. Dimensions : 2 RU / 483 x 88 x 454 mm (19" x 3.5" x 17.9“) | Phonic\'s MAX 2500 Power Amplifier provides 1500 Watts of power at 8 ohms (bridge mono) or 750 Watts at 4 ohms (stereo)- ideal for medium to large-size clubs, churches, auditoriums and more. Input to the MAX 2500 amp is achieved via combo connectors that accept both XLR and 1/4\' jacks, and output is achieved through either Speakon?-type connectors or binding posts. The MAX 2500 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making this amplifier ideal for real world application.
- Output power: 750W @ 4 Ohms stereo, 500W @ 8 Ohms stereo
- High-current toroidal transformers for greater power and low noise
- Independent user-defeatable peak limiters reduce distortion
- Selectable High-Pass filter at 30Hz or 50Hz
- XLR and 1/4\' TRS input jacks
- Binding post and Speakon?-type outputs
- Front mounted gain controls for easy access
- Signal and Peak LED indicators to monitor performance
- Short circuit, thermal, subsonic, RF protection, output DC offset
- Power on/off muting
| The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high • Laser cut aluminum front panels with integrated carrying handles • Neutrik® XLR input connectors, input and signal link in 2 channel models • Input Link switch: allow daisy-chaining of the input signal • Neutrik® Speakon® output connectors • Detented sealed potentiometers for easy recall of volume settings • ICL™, PMS™, Hi-temp, Signal indicators per channel • Power on and Stand-by leds • Highly versatile with multiple configuration and additional module options • Full PC control via EtheRAM (with EtheRAM Control module) • Switchable ICL™ clip-limiters per channel • Switchable (30-50 Hz) sub-sonic highpass filter per channel • Three-position gain selector (26, 32 or 38 dB) • Dual or bridge mode selector • Twin temperature controlled, back to front cooling fans • Oversized power components (high SOA reserve specification) Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics: • 2-way stereo crossover (dual mono or single bridged sub output) • 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz) • Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB) • Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics: • 4 Inputs/4 Outputs or 2 In/2 Out free route configurable. • 24 bits/192 kHz 256x Oversampling Converters. • Output Delay: 0 to 7.1 meters (20.69ms) per channel. • XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel. • EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB). • Gain, Mute and Phase inversion per channel. • RMS Power and Peak Voltage output limiter per channel. • Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module EtheRAM Control Module Ethernet Audio Transport (Coming soon) Analog Processor Module DSP44_S Module EtheRAM Control Module AES/EBU Digital Input (Coming soon)
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz Phase Response (@1W 20Hz-20kHz): ±15deg Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB Voltage Gain (selectable): 26/32/38 dB Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V 3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB 3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A 3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
Reviews
There are no reviews yet.