CRESTAUDIO PRO7200 2X1000W POWER AMPLIFIER

Pro 7200

Application
Designed with touring sound professionals in mind, the Crest Pro 200 Series power amplifiers
faithfully produce high power with low distortion in an extremely lightweight economical package.
Rock stable in stereo or bridged mode operation this series is engineered to exceed expectations,
when powering multiple or single loudspeaker enclosures down to a 2 ohm load.
The Pro 200 Series offer the protection that ensures safe & trouble free shows night after night.
Design Focus
The Pro 200 Series professional power amplifiers offer Crest's renowned sonic integrity while
providing exceptionally high power ratings (6500 W bridged on the Pro 9200) in a compact,
lightweight (under 25 lbs.) 2U package.
The Pro 200 Series amps feature Automatic Clip Limiting (ACL) to protect connected drivers;
IGM Impedance Sensing to accommodate varying impedance outputs; tunnel-cooled, high efficiency
heat sinksl and veriable-speed DC fans to limit the operating temperature and extend amplifier life.

FEATURES:
8 Ohm Stereo - 590 W
4 Ohm Stereo - 1000 W
2 Ohm Stereo - 1650 W
8 Ohm Bridged - 3400 W
Dramatically reduced net weight
Latest generation of high speed, wide-bandwidth output devices
Twin-tunnel cooling with back-to-front air flow
Dual, rear-mounted, continuous variable-speed fans
Balanced male and femal XLR inputs with switch-configurable XLR polarity
and sensitivity selection
Speakon? and five-way binding post output connectors
Ground-lift switch
Front panel circuit breaker switch
Modular construction
Five-year warranty
Dimensions 19" W x 3.5" H x 12.25" D
(483 mm x 89 mm x 312 mm)
Weight 21.8 lbs. (10 kg)

The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.

In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.

• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.

Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)


DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.


Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)

Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs

Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™

Number of Channels: 2

Output Power: (per channel)

8 ohms     450W
4 ohms  850W
2 ohms 1550W



Output Power: (bridged)

8 ohms 1700W
4 ohms 3100W


THD%: (@1dB below max output)

@ 1kHz

Power Rating    

Stereo Mode:
8Ω EIA 1 kHz 1% THD - 500W
4Ω EIA 1 kHz 1% THD - 850W
2Ω EIA 1 kHz 1% THD - 1250W

Bridged Mono:
8Ω EIA 1 kHz 1% THD - 1700W
4Ω EIA 1 kHz 1% THD - 2500W

Damping Factor     Not Specified By Manufacturer
Input Sensitivity     26dB Setting - 3.28V
32dB Setting - 1.60V
Input Impedance     > 10kΩ balanced, or unbalanced
Gain     34.5dB
Frequency Response     20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio     -106dB
Total Harmonic Distortion (THD)     0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections     Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors     Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel     AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear)     Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators     Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution     Flow-thru air path and solid aluminum heat sinks
Power Consumption     120V 50/60Hz - 8.5A
230V 50Hz - 7.5A
Power Requirements     Not Specified By Manufacturer
Dimensions (WxHxD)     19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight     33.5 lbs (15.2kg)
Specialties     Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity

BASIC Series - Intelligent Power

BASIC - that's meeting the tightest budgets and professional requirements
in reliability, flexibility and sound. Alone or in combination with the other
products of the Bittner portfolio.
The consequent realisation of the Bittner quality standards indicates once
more our understanding of the contracting business. It underlines our philosophy
that cost consciousness has nothing to do with giving up standards. Compromise
is a word unknown to Bittner Audio!
The incorporation of detent potentiometers, clip limiter, protection circuits for
any imaginable situation, as well as a first-class production process using only
highest-quality components made the BASIC series the choice of most contractors.

Certainly more than basic!

High Tech SMT design
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
XLR Inputs
Speakon and Binding Posts
Clip Limiter
Toroidal transformers
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed, low noise fans
Detent potentiometers
Stereo / Bridged / Parallel Mode
Ground Lift
Robust Steel Chassis
3 Year Warranty

TECHNICAL DATA:
Basic 1200:  2x 600 W @ 4 Ohm
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.03%
Signal-to-Noise Ratio: < -102 dB
Channel Seperation: > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  > 400 @ 4 Ohm
Cooling:  2x Fan (temp. reg. variable speed)
Weight:  15 kg.
Dimensions : 2 RU / 483 x 88 x 454 mm (19" x 3.5" x 17.9“)

This professional stereo power amplifier, working in class-H mode, provides 2x800W, at an efficiency of around 85%.

A passive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode. The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.  The integral soft clip limiter protects against damage to the connected loudspeakers.  The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.