Content |
Low weight switching final power amplifier. Power 2X2500W / 4Ω, 2Χ3000W / 2Ω. 5000W bridged 8Ω. New integrated BSS OMNIDRIVE 4bit / 192kHz processor with Cirus Logic SHARC A / D and D / A Converters. Level MAX peak voltage and RMS compressing, limiting. New hi-end FIR and IIR filters, 2sec delay / channel, as well as DSP presets for various speakers. LCD display on the front. USB port on the front for loading firmware and Speakers Tunning presets. Analog inputs with XLR, digital input AES / EBU, ethernet input RJ-45 with TCP / IQ protocol. Advanced 3rd generation power supply that allows the amplifier to operate at any voltage. Cooling circuit with microprocessor control with adjustable speed depending on the temperature. Analog and digital outputs (THRU) XLR. Exits speakon 5-way binding post, ground lift switch. Made of cast aluminum, height 2U rack. Suitable for P.A applications but also permanent installations. Weight 10.5kg |
Model T5n
Product Type Power Amplifier
Output Power (W) 1kHz THD+N=1% (120V)
2Ω per channel 2500
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 5000
8Ω bridge 4400
Output Power (W) 1kHz 20mS burst (120V)
2Ω per channel 3400
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 6800
8Ω bridge 4400
SN ratio (20Hz-20kHz) 107dB
THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω
Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1%
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB
Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB
Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu
Damping factorRL=8Ω 1kHz 800
Voltage Gain Att.max 26dB
Maximum Input Voltage +24dBu
Input Impedence 20kΩ (balance) 10kΩ (unbalance)
Controls Specifications
Front Panel POWER switch(push on/push off) attenuator (31 position) x2
Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1
Connectors Specifications
Input XLR-3-31 type/ch; Euroblock connector (balance)/ch
Output SPEAKON/ch, 5way biding postx1
Date Port RJ45x2
Indicators Specifications
Power/Standby x1 (Green/Orange)
Remote x1 (Green)
Protection x1 (Red)
Temp x1 (Red) heatsink temp 85°C
Signal x2 (Green)
Mute x2 (Red)
Clip/Limit x2 (Red)
Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically
Cooling Variable-speed fan: x2
Power requirements 120V/60Hz
Weight 14.0 kg
Dimensions (W x H x D) 480 x 88 x 456mm (2U) |
Model T4n Product Type Power Amplifier Output Power (W) 1kHz THD+N=1% (120V) 2Ω per channel 2200 4Ω per channel 1950 8Ω per channel 1150 4Ω bridge 4400 8Ω bridge 3900 Output Power (W) 1kHz 20mS burst (120V) 2Ω per channel 2900 4Ω per channel 1950 8Ω per channel 1150 4Ω bridge 5800 8Ω bridge 3900 SN ratio (20Hz-20kHz) 106dB THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1% Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu Damping factorRL=8Ω 1kHz 800 Voltage Gain Att.max 26dB Maximum Input Voltage +24dBu Input Impedence 20kΩ (balance) 10kΩ (unbalance) Controls Specifications Front Panel POWER switch(push on/push off) attenuator (31 position) x2 Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1 Connectors Specifications Input XLR-3-31 type/ch; Euroblock connector (balance)/ch Output SPEAKON/ch, 5way biding postx1 Date Port RJ45x2 Indicators Specifications Power/Standby x1 (Green/Orange) Remote x1 (Green) Protection x1 (Red) Temp x1 (Red) heatsink temp 85°C Signal x2 (Green) Mute x2 (Red) Clip/Limit x2 (Red) Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically Cooling Variable-speed fan: x2 Power requirements 120V/60Hz Weight 14.0 kg Dimensions (W x H x D) 480 x 88 x 456mm (2U)
|
Stereo Mode Ratings (Both Channels Driven):
8 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 1050W
- EIA 1 kHz, 0.1% THD: 1100W
4 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 1600W
- EIA 1 kHz, 0.5% THD: 2000W (1% THD)
2 ohms:
- EIA 1 kHz, 1% THD: 2500W
70V Direct Drive:
- EIA 1 kHz, 1% THD: 2500W
100V Direct Drive:
- EIA 1 kHz, 1% THD: 1000W
Bridged Mono Mode Ratings/Specifications:
8 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 3200W
- EIA 1 kHz, 0.1% THD: 3600W
4 ohms:
- EIA 1 kHz, 1% THD: 5000W
70V Direct Drive:
- EIA 1 kHz, 1% THD: 5000W
100V Direct Drive:
- EIA 1 kHz, 1% THD: 3600W
Signal to Noise, 20Hz-20kHz, 0.1% THD, 8 Ohms: > -100dB
Input Sensitivity @ 8 Ohms: 1.42V (+5.3 dBu)
Voltage Gain @ 8 Ohms: 64x (36 dB)
Output Circuitry: 3-tier Class H
Power Requirements (120V):
- 1/8 power pink noise at 4 ohms: 13.9A
- 1/3 power pink noise at 4 ohms: 26.9A
Power Requirements (230V):
- 1/8 power pink noise at 4 ohms: 7A
- 1/3 power pink noise at 4 ohms: 13.5A
Distortion (SMPTE-IM): |
The E Series is a range of lightweight, high-power switch mode amplifiers designed to the highest standards of reliability and sound quality. Developed for the touring market, E Series retain the sonic integrity of the benchmark MC and T Series amplifiers, without the physical weight. The switch mode power supply is capable of delivering high peaks without any perceptible bass 'sag' at very low distortion and is kept within its safe operating area by the new, sophisticated MC² Audio 'intelligent' limiter. The E15, E25, E45 and E4-75 feature MC² Audioʼs proprietary current driven output stages for ultra-high definition sound, delivered over the entire audio bandwidth. The E90 and the E100 are Class D amplifiers designed to meet the demands for higher power with increased efficiency whilst still maintaining the renowned MC² Audio sonic qualities and unsurpassed reliability. All MC² Audio products are covered by a 5 year warranty. Number of Channels: 2 Frequency Response: 20Hz to 20kHz (+/- 0.3dB) Output Power: (per channel) 8 ohms 1250W 4 ohms 2500W 2 ohms 4200W Output Power: (bridged) 8 ohms 5000W 4 ohms 8400W THD%: (@1dB below max output) @ 1kHz 20Hz to 20kHz Gain / Sensitivity: Gain 26/32/33dB Sensitivity (for max power) dBu +15.7/9.7/5.7 (4.7/2.4/1.5V) Power Consumption: Nominal @ 240v into 4 ohms 4.5A Nominal @ 120v into 4 ohms 9.0A Dimensions: (2U) (mm) Amplifier 88(h) x 482(w) x 428(d) Single Box (UK shipping) 230 x 580 x 560 Double Box (outside UK) 250 x 610 x 600 Weight: Amplifier 11.4kg Boxed (shipping weight) 13.4kg User's Manual
|
Dynacord H 5000
The power amp H5000 is part of Dynacord´s new PowerH SERIES, which marks a milestone in the design and the production of high-performance power amplifiers. The innovative 3-stage Grounded Bridge Class H Topology with "floatingË switching power supply unit offers very high and stable output with extreme high efficiency on an extremely high performance level at minimum weight. PowerH amps are ideal for driving professional touring, high-end Concert-Sound and Pro-Sound applications.
Dynacord H 5000 features:
2x 1500 Watt / 8 Ohm
2x 2500 Watt / 4 Ohm
2x 3500 Watt / 2 Ohm
Cooling: Front-to-Rear, 5-stage-fans
Dimensions (WxHxD): 483 x 88.1 x 498 mm
Weight: 14.5 kg
Protections:
Audio limiters
High temperature
DC
HF
Short Circuit
Back-EMF
Peak current limiters
Inrush current limiters
Turn-on delay
Mains Circuit Breaker Protection
Mains Overvoltage Protection
|
Reviews
There are no reviews yet.