| Content |
INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typically >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: |
The class-A circuit used in the EQ-73 is similar to the eq section in the classical 1073 module, without the high pass filter. Additional frequencies have been added and the mid frequency band uses two inductors, the higher value of the second one is used for the two lowest frequencies, 160 Hz and 240 Hz, to achieve a suitable response.
The sound character is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
The EQ-73 has stepped frequency controls that offers a wide selection of frequencies from 20 Hz to 24 kHz.
The Low and High frequency bands are shelving and the mid frequency band is of the bell type.
The control range is +/-15 dB for the two lower bands and +/- 18dB for the high frequency band.
There are separate bypass switches for all three bands.
The EQ-73 is made to be used together with one of our PRE-73 models that has an Insert jack. It can also be used with many other units that has a low level insert jack.
Combining a PRE-73 and an EQ-73, and using a UNITE rack kit to mount them together, one will get a 19-inch 1073-style unit at a low cost and with a great sound!
FEATURES
- Vintage Style electronics. No intergrated circuits in the signal path
- 3-band with a dual inductor based mid frequency band
- Stepped frequency selection
- A wide selection of frequencies from 20 Hz to 24 kHz
- Control range up to +/- 18 dB
- Separate Bypass switches for each band
- Tantalum capacitors in the signal path
- Made to be used together with one of our PRE-73 models with an Insert jack or any other unit with a low level Insert jack
- TRS jack for in-and output connection, the nominal working level is around 18 dBu
- Selectable ground lift switch
- External power supply to avoid interaction with the audio circuits
- Great sound that suits most sound sources and genres
- A solid build quality that will last many years of normal use
| 1231 Dual 31-Band Graphic Equalizer
The dbx? 12 Series were designed to meet the needs of the most demanding sound reinforcement environments, while offering the simplicity of straightforward controls. The 1231 provides standard features like dual-channels, 31 1/3 octave bands, ISO frequency centers, +/- 12 dB input gain range, and switchable 40Hz/18 dB per octave low-cut filters, but also includes other insightful features. These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS connectors for installation ease; balanced inputs and outputs for quiet operation; and chassis/signal ground lift capabilities for quick hum isolation. The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years of maintenance-free operation in any application. The magnetically isolated transformer, electronically balanced/unbalanced inputs and servo balanced/unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire relay bypass with 2 second power up delay were steps our engineers took to ensure compatibility for all installations. Only the best components were utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR (ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail is contained in a 3U steel/aluminum chassis.
SPECIFICATIONS:
| INPUT |
| Connectors: |
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip |
| Type: |
Electronically balanced/unbalanced, RF filtered |
| Impedance: |
Balanced 40 kOhm, unbalanced 20 kOhm |
| Max Input Level: |
>+21dBu balanced or unbalanced |
| CMRR: |
>40dB, typically >55dB at 1kHz |
| OUTPUTS |
| Connectors: |
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip |
| Type: |
Impedance-balanaced/unbalanced, RF filtered |
| Impedance: |
Balanced 200 ohm, unbalanced 100 ohm |
| Max Output Level: |
>+21dBu balanced/unbalanced into 2 kOhm or greater
>+18dBm balanced/unbalanced (into 600 ohm) |
| SYSTEM PERFORMANCE |
| Bandwidth: |
20Hz to 20kHz, +0.5/-1dB |
| Frequency Response: |
50kHz, +0.5/-3dB |
|
+/-15dB range |
+/-6dB range |
| Dynamic Range: |
109dB |
115dB |
| Signal-to-Noise: |
90dB |
97dB |
| THD + Noise: |
|
|
Phonic's GEQ3102F is the authentic soundman's choice of EQ - a dual channel 31-band equalizer, offering 6 or 12 dB of cut or boost on standard ISO center frequencies between 20 Hz and 20 KHz. The GEQ3102F is 2-rack space units high and accepts both 1/4" TRS phone jacks and XLR connectors, making it ideal for any studio or live venue setup.
- Sweepable high and low cut filters on each channel to remove unwanted frequencies
- Ultra low-noise audio operational amplifiers offer outstanding sound performance
- Relay-controlled hard-bypass with an auto-bypass function during power failure
- Dedicated subwoofer output with user-adjustable low-pass filter
- Feedback detection circuitry for indicating critical frequencies
- Balanced inputs and outputs with 1/4" TRS and XLR connectors
|
In today's recording and sound reinforcement environments, the need for multiple channels of high quality, easy to use compression is growing rapidly. The new dbx® 1046 is designed to provide the audio professional with just that: 4 channels of great sounding dbx compression for a variety of applications. Incorporating the industry standard dbx designs and the latest available manufacturing techniques, the dbx 1046 provides pristine sonic quality with that classic dbx sound.
The 1046 provides 4 channels of smooth classic dbx OverEasy® or Hard Knee compression that are perfectly suited for use on individual tracks of your multitrack recorder, and in virtually all applications the separate channels can be individually interfaced and used for entirely independent purposes. Additionally the newly developed PeakStopPlus™ is ideal for protecting your system from the oppressive peaks that can take out valuable drivers in your sound reinforcement rig or studio monitors.
All four channels have the following controls:
Threshold - allows you to set the level at which the compressor starts affecting the gain
OverEasy - allows you to select between soft compression for overall gain control or Hard Knee compression based on the characteristics of the original dbx 160.
Ratio - allows you to set the slope of gain reduction affecting the signal over the threshold level.
Input/Output Meter - allows you to set the meter to check the input and output levels for maximum signal-to-noise ratio and best level matching.
Output Gain - allows you to add make-up gain or to adjust the output level for that channel to match the next device's input gain.
Bypass - hard wire bypass allows you to hear how the compressor is affecting your signal.
PeakStopPlus - allows you to set the maximum signal level you want to pass through this channel. While it's virtually impossible to eliminate distortion, the PeakStopPlus circuit does it gracefully and effectively with minimal distortion.
Stereo Link - allows you to link channels 1&2 and 3&4 for two channels of true stereo compression.
All four channels feature balanced gold plated XLR and 1/4" inputs and outputs, and switchable +4dBu or -10dBV operating level to interface each individual channel with any other device.
So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx 1046 is for you.
- Four independent channels of operation, stereo linkable in two pairs
- PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
- Independent Threshold and ratio controls
- Switchable OverEasy® or Hard Knee compression
- Classic dbx® compression
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Precision metering of input level, output level, and gain reduction
- Dual True stereo or quad mono operation
- Switchable +4dBu or -10dBV operation per channel
| Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | | Input Type | Electronically balanced/unbalanced, RF filtered | | Input Impedance | Balanced > 40 kOhm, unbalanced >20 kOhm | | Max Input | > +22 dBu balanced or unbalanced | | CMRR | Typically >50 dB at 1 kHz | | Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | | Output Type | Servo-balanced/unbalanced, RF filtered | | Output Impedance | Balanced 30 Ohm, unbalanced 15 Ohm | | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | | Frequency Response | 0.35 Hz to 90kHz, +0/-3 dB | | Noise | | | Dynamic Range | > 118 dB, unweighted | | THD+Noise | >0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | | IMD | | | Interchannel Crosstalk | | | Stereo Coupling | True RMS Power Summing | | Compressor Threshold Range | -40 dBu to +20 dBu | | Compressor Ratio | 1:1 to infinity:1 | | Compressor Threshold Characteristic | Selectable OverEasy® or hard knee | | Compressor Attack/Release Characteristic | AutoDynamic™ | | Compressor Attack Time | Program-dependent | | Compressor Release Time | Program-dependent | | Compressor Output Gain | -20 to +20 dB | | Limiter Threshold Range | 0 dBu to +24 dBu (off) | | Limiter Ratio | infinity:1 | | Limiter Type | PeakStopPlus® two-stage limiter | | Limiter Stage 1 | PeakStop® brickwall limiter | | Limiter Stage 1 Attack Time | Zero | | Limiter Stage 1 Release Time | Zero | | Limiter Stage 2 | Predictive intelligent program limiter | | Limiter Stage 2 Attack Time | Program-dependent | | Limiter Stage 2 Release Time | Program-dependent | | OverEasy® Switch | Activates the OverEasy compression function | | I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter | | Bypass Switch | Activates the direct input-to-output hard-wire bypass | | Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels | | ST Link Switch | Links channels in stereo pairs. Channels One and Three become the master channels | | Gain Reduction Meter | 8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB | | I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu | | PeakStop™ Indicator | 1 LED to indicate PeakStop™ limiting | | Function Switches | LED indicator for each front-panel switch | | Output Transformer Options | Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx | | Operating Voltage | Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | | Power Consumption | 20 Watts | | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | | Power Connector | IEC receptacle | | Dimensions | 1.75“Hx19“Wx9“D (4.4cmx48.3cmx20.1cm) | | Unit Weight | 5.2 lbs. (2.4 kg) | | Shipping Weight | 7.6 lbs. (3.5 kg) |
| Bring a more professional sound to your mix
Adding a dbx® 266xs Compressor/Limiter/Gate to your live sound rig or studio gives you more dynamic control to help create a more polished, professional sound. Having compression in your audio chain gives you the ability to smooth out uneven levels, add sustain to guitars and fatten up your drums. It also makes it easy to bring vocals to the front of your mix - adding greater clarity and making them stand out from the surrounding instruments.
dbx knows compressors...after all we invented them! The 266xs is the latest in a long line of the world's most successful compressors from the inventors of the technology. Its patented Overeasy® compression technology provides smooth and musical performance while the AutoDynamic™ attack and release controls, found only on dbx compressors, puts great sound within easy reach. The 266xs can operate in stereo or dual-mono modes, has true RMS power summing and features quality XLR and 1/4" TRS inputs and outputs. It cuts no corners on visual feedback with gain reduction metering and easy-to-read backlit switches.
Features
- Error proof operation to smooth uneven levels, add sustain to guitars, fatten drums or tighten up mixes
- New gate timing algorithms ensure the smoothest release characteristics
- Program-adaptive expander/gates
- Great sounding dynamics control for any type of program material
- Separate precision LED displays for gain reduction, compression threshold and gate threshold allow quick, accurate setup
- Stereo or dual-mono operation
- Balanced inputs and outputs on 1/4" TRS and XLR connectors
- Side Chain insert
- Classic dbx® "Auto" mode
Specifications
| Input Connectors |
1/4" TRS and female XLR (pin 2 hot) |
| Input Type |
Electronically balanced/unbalanced, RF filtered |
| Input Impedance |
40kΩ balanced/unbalanced |
| Max Input |
>+22dBu Balanced or Unbalanced |
| Output Connectors |
1/4" TRS, female XLR (pin 2 hot) |
| Output Type |
Impedance-balanced/unbalanced, RF filtered |
| Output Impedance |
+4dBu: 100Ω balanced, 50Ω unbalanced; -10dBu: 1kΩ balanced, 500Ω unbalanced |
| Max Output |
>+21dBu balanced/unbalanced into 2kΩ or greater; >+18dBm balanced/unbalanced (into 600Ω) |
| Sidechain |
1/4" TRS Phone, Normalled: Ring = Output (send); tip = Input (return) |
| Sidechain Impedance |
Tip = >10kΩ (Input), Ring = 2kΩ (Output) |
| Sidechain Max Input Level |
Tip = >+22dBu (Input) |
| Sidechain Max Output Level |
Ring = >+20dBu (Output) |
| Compressor Threshold Range |
-40dBu to +20dBu |
| Compressor Threshold Characteristic |
Selectable OverEasy® or hard knee |
| Compressor Ratio |
1:1 to Infinity:1 |
| Compressor Attack Time |
Scalable Program-Dependent AutoDynamic™ |
| Compressor Release Time |
Scalable Program-Dependent AutoDynamic™ |
| Expander/Gate Threshold Range |
-60dBu to +15dBu |
| Expander/Gate Ratio |
1:1 to 4:1 |
| Expander/Gate Attack Time |
|
|
Reviews
There are no reviews yet.