| Content |
DBX 260 DRIVE RACK Complete Equalizaton & Loudspeaker Management System
There is a reason that Tour Sound Professionals and discriminating Audio
Contractors choose dbx? DriveRack? products for their high-end tours
and installs. The DriveRack products provide the tools that ensure that the
system sounds its very best. With the introduction of the new 260, the
heritage of unrivaled system/loudspeaker control continues.
The 260 capitalizes on the road tested and contractor approved nature of
the other products in the DriveRack line. The 260 provides full bandpass
and crossover configurations as well as independent output processing
and a full time RTA for live sound applications. Contractors will appreciate
its control inputs for wall-panel logic control and the patent-pending Advanced
Feedback Suppression (AFS?).
The DriveRack 260 continues the legacy of DriveRack series, which has
been created by the company that has been redefining the standard of
signal processing for more than 30 years. The DriveRack 260 was designed
with the purpose and vision of providing state-of-the-art signal processing,
while utilizing a simple and intuitive user interface. This goal has been
achieved by offering two independent channels of processing power with
a linkable 28-Band Graphic Equalizer, industry-standard dbx stereo
compressor module, feedback eliminator and the 120A Subharmonic
Synthesizer on the input, with a six channel output system that includes
parametric EQs, PeakStopPlus? limiters (to provide protection against
speaker blowouts) and alignment delay. These features combined with the
Wizard setup system and complete DriveWare? GUI control represent a
methodical design that is guaranteed to deliver optimal, all-inclusive processing
in a completely scalable system.
Features
* Feedback Elimination
* 2.7 Seconds of Alignment and Zone Delay
* RS-232 PC GUI control
* Classic dbx Compression and Limiting
* Graphic and Parametric EQ
* Auto-EQ Function
* Full Bandpass, Crossover, and Routing Configurations
* Auto Gain Control
* Pink Noise Generator and fulltime RTA
* Setup Wizard with JBL speaker and Crown Power Amplifier Tunings
* Security Lockout
* Wall Panel Control Inputs
| The LD Systems X223 is a stereo 2 way / mono 3 way crossover in standard 19"/1U rack format. Its rugged construction, high quality and robust knobs as well as the integrated power unit are rarities in this price range. It provides a mono sub output, an adjustable crossover frequency for each channel, adjustable LF/HF and input gains, phase reverse controls, switchable 40 Hz High-Pass filters and symmetrical XLR In- and Outputs. With the LD Systems X223 you get a crossover fulfilling the professional standards and offering great quality and sound characteristics.
Product type
Signal Processors
Version
2-way stereo/3-way mono
Frequency response
20 - 20.000 Hz
Signal-to-noise ratio
> 93 dB
Total Harmonic Distortion (THD)
< 0.004 %
Crosstalk
< - 80 (20 - 20.000 Hz) dB
Max. input level
+21 (balanced or unbalanced) dBu
Max. output level
+21 (balanced or unbalanced) dBu
Input impedance (kOhms)
50000 kOhm
Output impedance
200 Ohm(s)
Controls
2 x crossover frequency low/high, 2 x crossover low/mid, 2 x high gain, 2 x highpass (40 Hz), 2 x input gain, 2 x low gain, 2x frequency switch x1/x10, 4 x inv switch, LF sum, Mono/stereo mode
Indicators
2 x clip, 2 x crossover x 10, 2 x highpass, 4 x inv., mono, stereo
Line input connectors
XLR
Line output connectors
XLR
Mains connector
IEC socket
Operating voltage
220 V AC - 240 V AC
|
| Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
| Power connection: |
Mains input via Coaxial power connector (M) mounting version power supply cord with AC adapter (provided) |
| Frequency range: |
10 - 30000 Hz |
| THD: |
<0,005 % at 1 kHz |
| DSP: |
Digital signal processor |
| Impedance: |
Input: 10 kOhm
Output: 50 Ohm |
| Gain: |
Output: -50 dB to +12 dB |
| Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
| Delay: |
0 - 5 ms |
| Dynamic range: |
Input: 114 dB
Output: 110 dB |
| Sample rate: |
67 kHz |
| Connections: |
Input: line via 2 x 3-pin XLR
Output: line via 6 x 3-pin XLR |
| Crossover frequency: |
20-20000 Hz |
| Max. level: |
Input: +22 dBu
Output: +9 dBu |
| USB port: |
Typ B |
| PC connect: |
DXO Software via USB, firmware can be updated |
| Housing design: |
(19") 48.3 cm rack installation 1 U |
| Dimensions: |
Width: 48,3 cm
Depth: 12,8 cm
Height: 4,45 cm |
| Weight: |
1,77 kg |
| Operating system: |
Win XP, Win Vista, Win 7, Win 10, OS X 10,5 or better |
|
With the DSP 260 digital 2-in-6 sound system manager, DYNACORD is continuing its proud tradition in the fi eld of innovative digital signal processors.
Based on the most modern hardware, this system manager offers tried-and-tested as well as new algorithms for the simple and swift construction of active multi-way systems. As much importance has been attached here by the developers to high user-friendliness as to the realization of an extremely favorable price.
24-bit sigma-delta AD/DA converters and a 32-bit floating-point signal processor make possible a dynamic range of 111 dB. In addition to the two analog inputs, a digital stereo input in AES/EBU format is available. A -6 dB pad switch in front of the AD converters offers additional security against overload when the device is connected to mixing desks with very high output levels. The 6 individually mutable outputs are electronically balanced and available on XLR sockets. For all inputs and outputs, easily read LED level meters are provided on the front panel.
Users can choose whether to configure their own systems at the device itself using the controls and display provided or else by means of the intuitive editing software.
3-way stereo, 2-way stereo + FR, 4-way mono + FR etc. Furthermore, factory presets compatible with those of the tried-and-tested DSP-244 are available for Dynacord loudspeaker systems.
In terms of DSP, the device offers parametric and graphic EQs as well as a delay function in the input and crossover, channel EQ, channel delay and a level control with limiter in each output channel.
An RS-232 interface allows Master/Slave operation of multiple devices as well as GPI switching of settings. A PC (the editing software runs under Windows) can be connected via the USB interface on the front panel.
A variable parameter lockout function allows you to determine which settings and parameters can be accessed directly at the device. This is just one of many features that make the DSP 260 an ideal choice also for the rental business.
The wealth of features combined with its outstanding audio performance and favorable price commend this audio system manager for a multitude of professional applications.
General Mains Voltage 100-240 VAC 50-60 Hz Power Consumption 25W Audio Analog Inputs 2x XLR IN, electronically balanced, 2x XLR THRU OUT, electronically balanced Digital Inputs 1x XLR AES/EBU IN Nominal Input Voltage 1.23 V / +4 dBu Maximum Input Voltage (Without -6dB Analog Pad Engaged) 8.7 V / +21 dBu Input Impedance 10k ohm Common Mode Rejection -80 dB @ 1 kHz (typical) A/D Conversion 24-Bit Sigma-Delta Outputs 6x XLR OUT, electronically balanced Nominal Output Voltage 1.23 V / +4 dBu Maximum Output Voltage 8.7 V / +21 dBu Output Impedance 50 ohm D/A Conversion 24-Bit Sigma-Delta Frequency Response 10 Hz-22 kHz (+/- 0.5 dB) THD+N < 0.01% (band limited 22Hz-22kHz) Dynamic Range 111 dB unweighted, band limited 22 Hz - 22 kHz Interfaces USB USB Type B on front panel (PC Interface) 9-pin DSUB Software Confi gurable for GPI Preset Recall or Master/Slave Connection to second DSP 260 unit Signal Processing Sample Rate 48 kHz Data Format 24-Bit Internal Processing 32-Bit Floating Point Physical Dimensions (WxHx) 19 x 14 x 1.75 inches (482.6 x 355.6 x 44.45 mm) Weight (Net) 10.1 lb (4.6 kg) Weight (Gross) 13.0 lb (5.9 kg)
|
The DX 4008 is a complete 4 input - 8 output digital loudspeaker management system designed for the touring or fixed sound installation markets.
The absolute latest in available technology is utilized with 32-bit (40-bit extended) floating point processor and high performance 24-bit Analog Converters. The high-bit DSP prevents noise and distortion induced by truncation errors of the commonly used 24-bit fixed-point devices. A complete set of parameters include I/O levels, delay,polarity, 6 bands of parametric EQ per channel, multiple crossover selections and full function limiters. The DX 4008 can be controlled or configured in real time on the panel or with the intuitive PC GUI accessed via the RS 232 interface. Software upgrade for CPU and DSP via PC keeps the device current with newly developed algorithms and function once available. Multiple setup storage and system security complete this professional package.
| Features |
|---|
| The DX 4008 is a complete 4 input - 8 output digital loudspeaker management system designed for the touring or fixed sound installation markets | | Sampling rate can be set to 96kHz | | Precise frequency control is achieved with its 1 Hz resolution | | Inputs and outputs can be routed in multiple configuration to meet any requirements | | The DX 4008 is shipped with a special PC Graphic User Interface (GUI) application - XLink | | XLink gives the user an option to control the DX 4008 unit from a remote PC via the RS232 serial communication link | | The GUI application makes much easier control and monitor the device, allowing the user to get the whole picture on one screen | | Programs can be recalled and stored from/to PC's hard drive, thus expanding the storage to become virtuality limitless |
| INPUT AND OUTPUT SECTION |
|---|
| Input Impendance: | >10 | kΩ | | Output Impendance: | 50 | Ω | | Maximum Level: | + 20 | dBu | | Type: | XLR 3 | Electronically balanced |
| AUDIO PERFORMANCE |
|---|
| Frequency Response: | +/- 0.1 | dB (20 to 20 kHz) | | Dynamic Range: | 115 | dB typ (unweighted) | | CMMR: | > 60 | dB (50 to 10 kHz) | | Crosstalk: | | dB | | Distortion: | 0.001% | (1 kHz @ 18 dBu) |
| DIGITAL AUDIO PERFORMANCE |
|---|
| Resolution: | 32 bit | (40-bit extended) | | Sampling Rate: | 48 / 96 | kHz | | A/D - D/A Converters: | 24 | bit | | Propagation Delay: | 3 | ms | | No. of Programs: | 30 | |
| FRONT PANEL CONTROL |
|---|
| Display: | 4 x 26 | Character Backlit LCD | | Buttons: | 12 Mute Controls 12 Gain / Manu Controls 6 Menu Controls | | | “DATA" control: | (dial encoder) | Embedded Thumb Wheel | | Level Meters: | 5 | segment LED | | Interface | RS 232 | Female DB-9 |
| LIMITERS |
|---|
| Threshold: | -20 to +20 | dBu | | Attack Time: | 0.3 to 100 | ms | | Release Time: | 2 to 32 | X the attack time |
| EQUALISATION |
|---|
| Type: | Parametric, Hi-shelf, Lo-shelf | 6 per I/O | | Gain: | in 0.25dB steps | -30 to +15dB | | Bandwidth: | (Q=0.5 to 72) | 0.02 to 2.50 octaves |
| CROSSOVER FILTERS |
|---|
| Filter Types: | Butterworth, Bessel, Linkwitz Riley | | | Slopes: | 6 to 24dB/oct (96kHz) | 6 to 48dB/oct (48kHz) |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 | V ~ Hz | | Power (consumption): | | mA | | Fuse model: | | | | Operating temperature range: | 0 ÷ +55 | °C | | Operating humidity: | 20 ÷ 90 | % RH non-condensing |
| PHISICAL SPECIFICATION |
|---|
| Height: | 44 / 1.73 | mm/inch | | Width: | 483 / 19.01 | mm/inch | | Depth: | 203 / 7.99 | mm/inch | | Net Weight: | Kg/Lbs | 3 / 6.61 |
| SHIPPING INFORMATION |
|---|
| Package height: | 80 / 3.14 | mm/inch | | Package width: | 615 / 24.2 | mm/inch | | Package depth: | 360 / 14.17 | mm/inch | | Shipping Weight: | 4.3 / 9.4 | Kg/Lbs |
|
Based on a two-in, six-out topology, the DC-One is designed primarily for users of small-to-medium sized sound systems in both mobile and installed applications. While the unit is an all-new development based on a powerful SHARC processor, it is 100 percent compatible with all settings from other Electro-Voice signal processors. A large part of DC-Oneʼs development was aimed at ensuring that users can easily handle its serious digital horsepower and high-end audio performance. Free. PC-Editor software is available, or the DC-One can be operated via the front panel.
A/D Conversion 24-Bit Delta-Sigma
A/D Conversion 24-bit/sigma-delta (linear phase) 128 times oversampling
Analog Inputs 2 XLR (Electronically Balanced), 2 XLR THRU OUT (Electronically Balanced)
Analog Outputs 6 XLR (Electronically Balanced)
Control Protocol Front Panel USB Connector
D/A Conversion 24-bit/sigma-delta 128 times oversampling
D/A Conversion 24-Bit Delta-Sigma
Data Format 24-Bit
Digital Inputs 1 XLR AES/EBU (2 Ch)
Dynamic Range 111 dB (unweighted, band limited 22 Hz - 22 kHz)
Electronics Type Processor
FIR-Drive No
Frequency Response 10 Hz - 22 kHz (±0.5 dB)
Input Impedance (Balanced) 10 kΩ
Internal Processing 32-Bit Floating Point
Mains Voltage 100-240 VAC
Maximum Input Voltage 8.7 V / +21 dBu (Without -6 dB Analog Pad Engaged)
Maximum Output Voltage 8.7 V / +21 dBu
Nominal Input Voltage 1.23 V / +4 dBu
Nominal Output Voltage 1.23 V / +4 dBu
Output Impedance (Balanced) 50 Ω
Power Consumption 25 W
Sample Rate 48 kHz
THD+N < 0.01% (band limited 22 Hz - 22 kHz)
Height 1RU 44.45 mm (1.75“)
Width 482.6 mm (19“)
Depth 355.6 mm (14“)
Weight Net 4.6 kg (10.14 lbs) |
Reviews
There are no reviews yet.