| Content |
DBX-442 Complete Equalization and Loudspeaker Management System
442 DriveRack? Complete Equalization Management System. The DriveRack? 442
Complete Equalization Management System is the latest product in the DriveRack?
line. The 442 is based on the same operating system as the DriveRack? 480 and
offers the user four inputs and four outputs on XLR connectors. Each channel has EQ
in the form of a 9-Band Parametric or a 31-Band Graphic and Notch Filters. In addition
the 442 features a filter set that can be used to create a Highpass, Lowpass or Bandpass
filter. Dynamics processing is available on all channels with a Compressor/Limiter that
emulates the classic dbx? 160. The output section of the 442 offers delay, output level
and phase compensation. The 442 is also capable of running dual real-time analyzers
on channels three and four. A 480 master, a PC GUI, or a 480R remote can control the
442. Any combination of 480s, 481s, 482s and 442s can be controlled on a single
DriveRack? network consisting of up to 100 units.
Features
* 4 Inputs and 4 Outputs
* 31-band graphic or 9 band parametric equalizer on every input
* Time Alignment Delay
* Compressor/Limiter on every output
* Multi-level Security System
* Separate House and Show EQ with individual lockouts
* Triple redundant back up of all parameters when running network, 480R and GUI
* Type IV? Conversion System
* Electronically balanced/RF filtered XLR Inputs and Outputs
* Proprietary RS-485 Control Network
* RS-232 PC Interface for computer display and configuration
|
Based on a two-in, six-out topology, the DC-One is designed primarily for users of small-to-medium sized sound systems in both mobile and installed applications. While the unit is an all-new development based on a powerful SHARC processor, it is 100 percent compatible with all settings from other Electro-Voice signal processors. A large part of DC-Oneʼs development was aimed at ensuring that users can easily handle its serious digital horsepower and high-end audio performance. Free. PC-Editor software is available, or the DC-One can be operated via the front panel.
A/D Conversion 24-Bit Delta-Sigma
A/D Conversion 24-bit/sigma-delta (linear phase) 128 times oversampling
Analog Inputs 2 XLR (Electronically Balanced), 2 XLR THRU OUT (Electronically Balanced)
Analog Outputs 6 XLR (Electronically Balanced)
Control Protocol Front Panel USB Connector
D/A Conversion 24-bit/sigma-delta 128 times oversampling
D/A Conversion 24-Bit Delta-Sigma
Data Format 24-Bit
Digital Inputs 1 XLR AES/EBU (2 Ch)
Dynamic Range 111 dB (unweighted, band limited 22 Hz - 22 kHz)
Electronics Type Processor
FIR-Drive No
Frequency Response 10 Hz - 22 kHz (±0.5 dB)
Input Impedance (Balanced) 10 kΩ
Internal Processing 32-Bit Floating Point
Mains Voltage 100-240 VAC
Maximum Input Voltage 8.7 V / +21 dBu (Without -6 dB Analog Pad Engaged)
Maximum Output Voltage 8.7 V / +21 dBu
Nominal Input Voltage 1.23 V / +4 dBu
Nominal Output Voltage 1.23 V / +4 dBu
Output Impedance (Balanced) 50 Ω
Power Consumption 25 W
Sample Rate 48 kHz
THD+N < 0.01% (band limited 22 Hz - 22 kHz)
Height 1RU 44.45 mm (1.75“)
Width 482.6 mm (19“)
Depth 355.6 mm (14“)
Weight Net 4.6 kg (10.14 lbs) |
| Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
| Power connection: |
Mains input via Coaxial power connector (M) mounting version power supply cord with AC adapter (provided) |
| Frequency range: |
10 - 30000 Hz |
| THD: |
<0,005 % at 1 kHz |
| DSP: |
Digital signal processor |
| Impedance: |
Input: 10 kOhm
Output: 50 Ohm |
| Gain: |
Output: -50 dB to +12 dB |
| Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
| Delay: |
0 - 5 ms |
| Dynamic range: |
Input: 114 dB
Output: 110 dB |
| Sample rate: |
67 kHz |
| Connections: |
Input: line via 2 x 3-pin XLR
Output: line via 6 x 3-pin XLR |
| Crossover frequency: |
20-20000 Hz |
| Max. level: |
Input: +22 dBu
Output: +9 dBu |
| USB port: |
Typ B |
| PC connect: |
DXO Software via USB, firmware can be updated |
| Housing design: |
(19") 48.3 cm rack installation 1 U |
| Dimensions: |
Width: 48,3 cm
Depth: 12,8 cm
Height: 4,45 cm |
| Weight: |
1,77 kg |
| Operating system: |
Win XP, Win Vista, Win 7, Win 10, OS X 10,5 or better |
| More sound to your amps and speakers
The secret to making speakers sound great lies with the crossover you use. With the dbx® 234xs Crossover you'll get great performance, ultra low-noise, rugged reliability and four decades of dbx knowledge and expertise in building the world's finest processors. The 234xs uses precision filters to separate the audio signal and direct the correct frequencies to your loudspeaker drivers. By directing only the specific frequency bands to each speaker driver the 234xs leaves your amplifiers free to use their full power on the usable signal eliminating distortion and giving your PA system a cleaner and better sound.
The dbx 234xs is a dual channel crossover with all the features you would expect from a professional product. It features Linkwitz-Riley 24dB per octave filters, independent output gain controls for level matching, output phase inversion, 40 Hz low cut filter, and optional mono summing of the low frequency (subwoofer) output. Everything in the design exudes great precision from the solid "click" controls to the high quality XLR inputs and outputs.
XLR balanced ins and outs
Mode switches for mono 4-way or stereo 2-way/3-way operation
Low frequency summed (subwoofer) output
x10 range switch on both channels
40Hz high pass (low cut) filter both channels
Phase reverse switch on all outputs
Individual level controls on all outputs
24dB per octave Linkwitz-Riley filters (the professional standard)
Stereo/Mono status LEDs indicate the selected mode
dbx® 2 year parts and labor as standard
CSA NRTL/C approved
CE compliant
| Input Connectors |
XLR |
| Input Type |
Electronically balanced/unbalanced, RF filtered |
| Input Impedance |
Balanced >50k ohm, unbalanced >25k ohm |
| Max Input |
>+22dBu balanced or unbalanced |
| CMRR |
>40dB, typically >55dB at 1kHz |
| Output Connectors |
XLR |
| Output Type |
Impedance-balanaced/unbalanced, RF filtered |
| Output Impedance |
Balanced 200 ohm, unbalanced 100 ohm |
| Max Output |
>+21dBu balanced/unbalanced into 2k ohms or greater |
| Bandwidth |
20Hz to 20kHz, +/-0.5dB |
| Frequency Response |
90 kHz, +0/-3 dB |
| Signal to Noise Ratio |
Ref: +4 dBu, 22 kHz measurement bandwidth |
| Signal-to-Noise (Stereo Mode) |
>94dB (Low Output), >93dB (Mid Output), >90dB (High Output) |
| Signal-to-Noise (Mono Mode) |
>94dB (Low Output, Low/Mid Output); >92dB (High/Mid Output); >88dB (High Output) |
| Dynamic Range |
> 106 dB, unweighted, any output |
| THD+Noise |
| Interchannel Crosstalk |
| Crossover Frequencies (Stereo Mode) |
Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High 450Hz to 9.6kHz (x10 setting) |
| Crossover Frequencies (Mono Mode) |
Low/Low-Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low-Mid/High-Mid: 450 Hz to 9.6 kHz; High-Mid/High: 450 Hz to 9.6 kHz |
| Crossover Filter Type |
Linkwitz-Riley, 24 dB/octave, state-variable |
| Low cut Switch |
Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel. |
| Phase Invert Switch |
Inverts the phase at the output, one switch per output. |
| x1 / x10 Switch |
Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel. |
| Mode Switch |
Selects stereo/mono and 2/3/4-way operation |
| LF Sum Switch |
Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2ʼs low output phase invert LED to indicate that this output is not operational in the LF sum mode. |
| Indicators |
Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output) |
| Operating Voltage |
100-120 VAC 50/60Hz; 120 VAC 60Hz 230 VAC 50/60Hz |
| Operating Temperature |
32°F to 113°F (0°C to 45°C) |
| Power Consumption |
15W |
| Power Connector |
IEC receptacle |
| Dimensions |
1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm) |
| Unit Weight |
4.0 lbs. (1.8 kg) |
| Shipping Weight |
5.8 lbs. (2.6 kg) |
|
Full-featured Speaker Processing in a 1U Space
Speaker processing can be a complicated business requiring a substantial array of equipment, but the Yamaha SP2060 offers everything you need in a single rack space. This innovative 24-bit, 96-kHz digital speaker processor delivers excellent sound quality, an impressive variety of processing functions — gain, delay, PEQ, comp, crossover, limiter, and an all-pass filter for phase adjustment — and intuitive programming from Yamaha's DME Designer application running on a personal computer. It has two analog inputs and six analog outputs, plus two AES/EBU format digital inputs for connectivity with a broad range of systems. And if you use Yamaha Installation Series Speakers, all you need to do is select one of the many optimized presets provided for great sound with minimum measurement and setup time. The SP2060 is a compact, portable 1U unit that is ideal for live sound or installations.
| Sampling Frequency | Internal Clock | 96kHz | | External Clock | Normal Rate | 44.1, 48kHz (±0.1%) | | Double Rate | 88.2, 96kHz (±0.1%) | | Signal Delay | 761µsec Input to Output, fs = 96kHz | | Frequency Response | 20Hz -40kHz (TYP 0dB, MAX +0.5dB, MIN -1.0dB), fs=96kHz, RL=600ohms | | Total Harmonic Distortion | 0.007% (+22dBu@1 kHz),
0.05% (+4dBµ@20 Hz - 40kHz)
fs=96kHz, RL=600ohms;
measured with 18dB/octave filter @80kHz | | Hum & Noise | TYP -82dBu,
fs=96kHz, RL=600ohms, Rs=150 ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞ dB/octave attenuation. | | Dynamic Range | 106dB AD+DA
fs=96kHz, RL=600ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞dB/octave attenuation. | | Crosstalk @1kHz | -80dB INPUT to Output
fs=96kHz, measured with 18dB/octave filter @80kHz | | Power Consumption | 30W | | Dimensions (W x H x D) | 480 x 44x 360.2mm | | Net Weight | 4.2kg |
| Advanced Feedback Suppression Processor with Full LCD Display
The AFS2 Dual-Channel Advanced Feedback Suppression Processor from DBX protects your ears and audio equipment from annoying and potentially damaging audio feedback without altering your sound. The AFS2 features application-specific filter types for speech, music low, music medium, and music high. The 24 fixed or live narrow-band notch filters are capable of removing frequencies at 1/80 of an octave, ensuring an optimal frequency response without the possibility of feedback.
The front panel features the wizard function to take the guesswork out of setting up any room by incorporating an advanced feedback suppression module and providing a full LCD display for system settings and menus. Additionally, the AFS2 offers a five-segment LED for accurately monitoring input levels for each channel, while the notch filter indicator allows you to monitor the number of filters applied. Dedicated bypass buttons are included to help isolate problem channels. The rear panel offers XLR and 1/4" inputs and outputs, both switchable between +4 and -10 dB operations. A USB port has been provided for firmware updates. The AFS2 ships with a standard IEC power cable.
| Number of Channels |
2 |
| Inputs |
Connectors: Female XLR and 1/4" TRS
Type: Electronically balanced and unbalanced, RF filtered
Impedance: Balanced 50 kohm, unbalanced 25 kohm
Max Line Level: +20 dBu |
| Input CMRR |
>40 dB, typically >55dB @ 1 kHz |
| Outputs |
Connectors: Male XLR and 1/4" TRS
Type: Electronically balanced and unbalanced, RF filtered
Impedance: Balanced >120 ohms, unbalanced >60 ohms
Max Level: +20 dBu |
| A/D/A Converter |
A/D Converter: DBX type IV conversion system
A/D Dynamic Range: >113 dB A-weighted, >110 dB, unweighted, 22 kHz BW
Type IV Dynamic Range: >119 dB, A-weighted, 22 kHz BW; >117 dB, unweighted, 22 kHz BW
A/D Conversion: 24-bit
Sample Rate: 48 kHz
D/A Dynamic Range: 112 dB A-weighted, 109 dB unweighted
D/A Conversion: 24-bit |
| Dynamic Range |
109 dB A-weighted, 106 dB unweighted, 22 kHz BW |
| THD + Noise |
0.003% typical at +4 dBu, 1 kHz |
| Frequency Response |
20 Hz to 20 kHz, ±0.5dB |
| Crosstalk |
Interchannel Crosstalk: >80 dB typical
Crosstalk Input to Output: >80 dB |
| Power |
US: 100 to 120 VAC 60 Hz
EU: 220 to 240 VAC 50 Hz
9 W |
| Dimensions (HxDxW) |
1.8 x 5.8 x 19.0" / 4.4 x 14.6 x 48.3 cm |
| Weight |
4.5 lb / 2.0 kg |
|
Reviews
There are no reviews yet.