Content |
DBX-442 Complete Equalization and Loudspeaker Management System
442 DriveRack? Complete Equalization Management System. The DriveRack? 442 Complete Equalization Management System is the latest product in the DriveRack? line. The 442 is based on the same operating system as the DriveRack? 480 and offers the user four inputs and four outputs on XLR connectors. Each channel has EQ in the form of a 9-Band Parametric or a 31-Band Graphic and Notch Filters. In addition the 442 features a filter set that can be used to create a Highpass, Lowpass or Bandpass filter. Dynamics processing is available on all channels with a Compressor/Limiter that emulates the classic dbx? 160. The output section of the 442 offers delay, output level and phase compensation. The 442 is also capable of running dual real-time analyzers on channels three and four. A 480 master, a PC GUI, or a 480R remote can control the 442. Any combination of 480s, 481s, 482s and 442s can be controlled on a single DriveRack? network consisting of up to 100 units.
Features
* 4 Inputs and 4 Outputs * 31-band graphic or 9 band parametric equalizer on every input * Time Alignment Delay * Compressor/Limiter on every output * Multi-level Security System * Separate House and Show EQ with individual lockouts * Triple redundant back up of all parameters when running network, 480R and GUI * Type IV? Conversion System * Electronically balanced/RF filtered XLR Inputs and Outputs * Proprietary RS-485 Control Network * RS-232 PC Interface for computer display and configuration
|
With the DSP 260 digital 2-in-6 sound system manager, DYNACORD is continuing its proud tradition in the fi eld of innovative digital signal processors. Based on the most modern hardware, this system manager offers tried-and-tested as well as new algorithms for the simple and swift construction of active multi-way systems. As much importance has been attached here by the developers to high user-friendliness as to the realization of an extremely favorable price. 24-bit sigma-delta AD/DA converters and a 32-bit floating-point signal processor make possible a dynamic range of 111 dB. In addition to the two analog inputs, a digital stereo input in AES/EBU format is available. A -6 dB pad switch in front of the AD converters offers additional security against overload when the device is connected to mixing desks with very high output levels. The 6 individually mutable outputs are electronically balanced and available on XLR sockets. For all inputs and outputs, easily read LED level meters are provided on the front panel. Users can choose whether to configure their own systems at the device itself using the controls and display provided or else by means of the intuitive editing software. 3-way stereo, 2-way stereo + FR, 4-way mono + FR etc. Furthermore, factory presets compatible with those of the tried-and-tested DSP-244 are available for Dynacord loudspeaker systems. In terms of DSP, the device offers parametric and graphic EQs as well as a delay function in the input and crossover, channel EQ, channel delay and a level control with limiter in each output channel. An RS-232 interface allows Master/Slave operation of multiple devices as well as GPI switching of settings. A PC (the editing software runs under Windows) can be connected via the USB interface on the front panel. A variable parameter lockout function allows you to determine which settings and parameters can be accessed directly at the device. This is just one of many features that make the DSP 260 an ideal choice also for the rental business. The wealth of features combined with its outstanding audio performance and favorable price commend this audio system manager for a multitude of professional applications. General Mains Voltage 100-240 VAC 50-60 Hz Power Consumption 25W Audio Analog Inputs 2x XLR IN, electronically balanced, 2x XLR THRU OUT, electronically balanced Digital Inputs 1x XLR AES/EBU IN Nominal Input Voltage 1.23 V / +4 dBu Maximum Input Voltage (Without -6dB Analog Pad Engaged) 8.7 V / +21 dBu Input Impedance 10k ohm Common Mode Rejection -80 dB @ 1 kHz (typical) A/D Conversion 24-Bit Sigma-Delta Outputs 6x XLR OUT, electronically balanced Nominal Output Voltage 1.23 V / +4 dBu Maximum Output Voltage 8.7 V / +21 dBu Output Impedance 50 ohm D/A Conversion 24-Bit Sigma-Delta Frequency Response 10 Hz-22 kHz (+/- 0.5 dB) THD+N < 0.01% (band limited 22Hz-22kHz) Dynamic Range 111 dB unweighted, band limited 22 Hz - 22 kHz Interfaces USB USB Type B on front panel (PC Interface) 9-pin DSUB Software Confi gurable for GPI Preset Recall or Master/Slave Connection to second DSP 260 unit Signal Processing Sample Rate 48 kHz Data Format 24-Bit Internal Processing 32-Bit Floating Point Physical Dimensions (WxHx) 19 x 14 x 1.75 inches (482.6 x 355.6 x 44.45 mm) Weight (Net) 10.1 lb (4.6 kg) Weight (Gross) 13.0 lb (5.9 kg)
| Behringer CX-3400 3-Way Stero/4-Way Mono Frequency Crossover with Limiters
The CX3400 is an active frequency crossover enabling 2 or 3-way stereo or even 4-way mono operation. Each band features two 24-dB Linkwitz-Riley filters, as well as individual IGC limiters, while the integrated delay enables flexible time alignment. Polarity switches for each output allow quick and easy runtime compensation for various driver and horn types.2
Respectively:
3-Way stereo or 4-way mono
24 dB / octave Linkwitz-Riley filter
Mono-Sub switchable
LF / HF gain regular / mutable
CD horn EQ switchable
Vertex frequency tunable
Factor switching (10x)
Multi-band limiter switch / variable (threshold)
Limit display each way
LF Delay (max 2ms / 60cm)
Phase reverse
25 Hz subsonic filter, sym
XLR in / out with multiband limiters
Dimensions: 19", 1U, 147 mm case depth
Weight: 1.7 kg |
Based on a two-in, six-out topology, the DC-One is designed primarily for users of small-to-medium sized sound systems in both mobile and installed applications. While the unit is an all-new development based on a powerful SHARC processor, it is 100 percent compatible with all settings from other Electro-Voice signal processors. A large part of DC-Oneʼs development was aimed at ensuring that users can easily handle its serious digital horsepower and high-end audio performance. Free. PC-Editor software is available, or the DC-One can be operated via the front panel.
A/D Conversion 24-Bit Delta-Sigma A/D Conversion 24-bit/sigma-delta (linear phase) 128 times oversampling Analog Inputs 2 XLR (Electronically Balanced), 2 XLR THRU OUT (Electronically Balanced) Analog Outputs 6 XLR (Electronically Balanced) Control Protocol Front Panel USB Connector D/A Conversion 24-bit/sigma-delta 128 times oversampling D/A Conversion 24-Bit Delta-Sigma Data Format 24-Bit Digital Inputs 1 XLR AES/EBU (2 Ch) Dynamic Range 111 dB (unweighted, band limited 22 Hz - 22 kHz) Electronics Type Processor FIR-Drive No Frequency Response 10 Hz - 22 kHz (±0.5 dB) Input Impedance (Balanced) 10 kΩ Internal Processing 32-Bit Floating Point Mains Voltage 100-240 VAC Maximum Input Voltage 8.7 V / +21 dBu (Without -6 dB Analog Pad Engaged) Maximum Output Voltage 8.7 V / +21 dBu Nominal Input Voltage 1.23 V / +4 dBu Nominal Output Voltage 1.23 V / +4 dBu Output Impedance (Balanced) 50 Ω Power Consumption 25 W Sample Rate 48 kHz THD+N < 0.01% (band limited 22 Hz - 22 kHz) Height 1RU 44.45 mm (1.75“) Width 482.6 mm (19“) Depth 355.6 mm (14“) Weight Net 4.6 kg (10.14 lbs) |
Lab Gruppen NLB 60E
The NomadLink network provides remote monitoring, control and power sequencing functions for multiple C Series or FP+ amplifiers. Indeed up to 16 NLB 60E network bridges, each monitoring up to 60 amplifiers may be accommodated in one system. Easy setup, redundancy, and minimum maintenance were bywords when developing this network format.
NomadLink is a closed-loop, daisy-chained network topology with the NLB 60E providing the bridge to the familiar world of Ethernet/LAN. NomadLink reduces installation time and cost significantly, includes redundancy during operation by design and simplifies the location of faults or system abuse.
NomadLink together with the associated DeviceControl software allows the subnets’ architecture to be automatically uploaded even without individual IP addresses in the amplifiers. All in all, it is the fastest and easiest monitoring and control network on the market today.
Specifications:
Network Connectors:
* Nomadlink Out: EtherCon housed RJ45
* Nomadlink In: EtherCon housed RJ45
* Ethernet rear-panel: EtherCon housed RJ45
* Ethernet front-panel: Standard RJ45
General Purpose Inputs (GPI):
* One Voltage sensing input: Two pole Phoenix
* Two contact closure inptus: Two pole Phoenix
Front Panel Indicators:
* Front operation locked: Yellow LED
* Fault warning: Red LED
* Amplifier subnet muted: Red LED
* NomadLink network connected/activity: Blue LED
* Ethernet connected: Orange LED
* Ethernet Activity: Yellow LED
2 x 16 Character display: White text, Blue background
Navigation and Adjust keys: Yes, x 6
Subnet Power on/off keys: Yes, x 2
Power: 100 to 240 VAC, 50 to 60 Hz (auto-select)
Power consumption:
Finish: Anodized aluminum front, Plated and painted steel chassis
Approvals: CE, CSA
Dimensions (W x H x D): 19" x 1.73" x 8.2" (483 x 44 x 208 mm), 1 RU
Weight: 5 lbs. (2.25 kg)
|
Providing 48-bit filter algorithms, 24-bit AD/DA conversion and a dynamic range of 115 dB, the DSP 244 sets new standards for digital loudspeaker controllers and processors. The DSP 244 is an universal Digital Sound System Processor that provides 2 inputs and 4 outputs; plus internal summing of the inputs 1 and 2. Via matrix it is possible to assign the outputs to any input or to the sum of the inputs. It is further possible to establish the following configurations: Stereo or Dual 2-Way systems, 3-Way + Direct and 4-Way systems, each with Mono Subchannel, but also full range systems. High and low-pass filters are provided for the frequency crossover functions in all operation modes. The selection includes Linkwitz-Riley, Butterworth and Bessel type filters with switchable slopes between 6, 12, 18 and 24 dB/oct. A huge number of additional filters offers extremely flexible correction of the frequency response. Each input incorporates a 5-band equalizer, allowing to assign high and low-pass, high and low-shelving or parametric peak-dip filters to its individual filter sections. Next to the frequency crossover filters, four additional filters are employed in each output channel, which also can be set to work as high or low-pass, high or low-shelving filters, parametric peak-dip filters, or all-pass filters. Additional filtering is provided through 2. order high-passes for the realization of B-6 alignment, or special LPN-filters (Low-Pass Notch filters) for correcting the frequency and phase responses of optimally vented woofer cabinets. Each channel additionally provides a delay, a polarity switch, a programmable level control and a digital compressor / limiter while the master delays are located in the input channels. Datasheets / ManualsBrochure (309KB)
Mains voltage 90 - 250 V AC / 50 - 60 Hz Power consumption 20 watts Safety class I Inputs 2 x XLR IN, electronically balanced, transformer optional available 2 x XLR OUT (Direct Out) Input voltage (nominal) 1.55 V / + 6 dBu Max. input voltage 24.5 V / + 30 dBu Input impedance 20 kohms Common mode rejection > 40 dB AD-conversion 24-bit, Sigma-Delta, 128 times oversampling, linear phase Outputs 4 x XLR OUT, electronically balanced Output voltage (nominal) 1.55 V / + 6 dBu Max. output voltage 8.7 V / + 21 dBu Output impedance |
Reviews
There are no reviews yet.