Content |
The 481 and 482 are slave units which include all of the functionality and features of the 480 . They both incorporate 4 inputs and 8 outputs with Euroblock connectors on the 481 and XLRs on the 482. However, they do not include the front panel programming interface. All programming functions can be performed through the 480, the 480R, or via the Windows GUI. An unlimited number of slaves can be chained together.
Features: 4 Input and 8 Outputs with routing 31 band graphic or 9 band parametric equalizer on every input (pre-crossover) Dual Real Time Audio Analyzers Butterworth, Bessel or Linkwitz-Riley crossover filters 27 Different Crossover Configurations Time Alignment and Transducer Alignment Delays Compressor/Limiter on every output Speaker Compensation EQ (post crossover) Multi-level Security System Separate House and Show EQ with individual lockout Triple redundant back-up of all parameters when running network, 480R and PC GUI TYPE IV? Conversion System Electronically balanced/RF filtered Euroblock Inputs and Outputs Proprietary RS-485 Control Network RS-232 PC Interface for computer display and configuration |
The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers. It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on the back panel selecting either mode.
Features Ultra low noise circuitry Totally phase aligned at crossover point Switchable Dual Channel 2 way or Single Channel 3 way Unique 'semi-fixed' crossover point 24dB per octave (Fourth Order) Linkwitz-Riley filters Separate Summed Mono Output Balanced Inputs and Outputs Built in High Pass filters Intuitive, 'user friendly' layout Flawless performance in any audio environment
Tamper-Proof Crossover Points The crossover points are determined internally by the value of 4 resistors per channel; changing the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of externally adjusted crossover points, making the crossover points tamper-proof once they are set. Idle fingers can't fiddle with the crossover points and create havoc with the system! As a handy guide, a list of common crossover points and their corresponding resistor values are printed inside the unit's lid, and also set out in the Owner's Manual. On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid and High in single channel 3 way mode, with corresponding Outputs on the rear panel.
Balanced Inputs and Outputs EC-2 has Balanced Inputs and Outputs, on XLR connectors. The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low feed (e.g. Left and Right full-range plus a single Sub Bass speaker). High Pass Filter There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers and waste amplifier power. In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of differing sensitivities. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage change switch. Uncompromising Audio Quality Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels. It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the crossover region. From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX EC-2 is a crossover that is suited to any application that requires flawless, transparent sound. You'll never compromise on Quality when you choose ARX
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 21 dB CMRR >45 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 21dB Frequency Response 30Hz-20KHz +or- 0.5dB Note: 30 Hz is a function of the High Pass filter Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted Distortion 004% THD,0dB,1KHz Dynamic Range 111 dB Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm Input Connector type XLR Output Connector type XLR Crossover point frequencies are changed internally by varying the value of 4 resistors per channel.
Front Panel Controls Low and High Output controls for 2 way mode Low, Mid and High Output controls for 3 way mode Marker panels for labelling crossover assigns 2 way/ 3 way status LEDs Rear Panel Balanced XLR Inputs and Outputs Additional summed mono Low output 2 way / 3 way mode switch | Crossover 2-Way stereo or 3-way mono mode Additional subwoofer output Linkwitz-Riley filter with 24 dB / octave Sub-woofer frequency range separately adjustable Individual output gain controls and output mute switch for all bands 2 Balanced XLR inputs with gold-plated contacts 5 Balanced XLR outputs with gold-plated contacts Switchable 25 Hz low-cut filter to protect loudspeakers from infrasound Easy-to-read status LEDs Built-in power supply 100-240V, 50-60 Hz Dimensions (H x W x D): 44 x 483 x 147 mm Weight: 1.6 kg | The DriveRack® PA2 provides all the processing you need between your mixer and amplifiers to optimize and protect your loudspeakers. With the latest advancements in dbx's proprietary AutoEQTM and AFSTM algorithms, a new input delay module for delaying the FOH system to the backline, Ethernet control via an Android®, iOS®, Mac®, or Windows® device, and updated Wizards, the DriveRack PA2 continues the DriveRack legacy of great-sounding, powerful, and affordable loudspeaker management processors, for a whole new generation.
Available Input Processing
- dbx Compression
- AFSTM (Advanced Feedback Suppression)
- Graphic EQ
- 8-Band Parametric EQ (adjusted when using the AutoEQ)
- Subharmonic Synthesis
Available Output Processing
- Crossover (supports full range, 2-way, and 3-way systems)
- 8-Band Parametric EQs (used for speaker tunings)
- dbx Limiting
- Driver Alignment Delays
Input |
(2) line inputs. (1) RTA Mic input |
Input Connectors |
(2) Female XLR line inputs. (1) Female XLR RTA Mic input |
Input Type |
Electronically balanced/RF filtered |
Input Impedance |
>50 kohm |
A/D Converter |
dbx Type IVTM Conversion System |
CMRR |
> 45dB |
Mic Preamp Phantom Power |
+15VDC (RTA) |
Mic Preamp Equivalent Input Noise (EIN) |
|
Output |
(6) Line Outputs |
Output Connectors |
Male XLR |
Output Type |
Electronically balanced, RF filtered |
Output Impedance |
120 Ω |
Max Output |
+20dBu |
A/D Dynamic Range |
112 dB A-weighted, 110 dB unweighted |
Type IV Dynamic Range |
123 dB with transient material, A-weighted, 22kHz BW; 121 dB with transient material, unweighted, 22kHz BW; 115 dB typical with program material, A-weighted, 22kHz BW |
Input Delay Length |
100ms |
Alignment Delay |
10ms per channel (60ms total) |
Sample Rate |
48kHz |
Dynamic Range |
>110 dB A-weighted, >107dB unweighted |
THD+Noise |
0.003% typical at +4dBu, 1kHz, 0dB input gain |
Frequency Response |
20Hz - 20kHz, +/- 0.5dB |
Interchannel Crosstalk |
|
Operating Voltage |
100-120VAC 50/60 Hz - EU: 220-240 VAC 50/60 Hz |
Power Consumption |
22 W |
Unit Weight |
5.25 lbs. (2.4 kg) |
Shipping Weight |
6.75 lbs. (3.1 kg) |
Dimensions |
1.75" (H) x 5.75" (D) x 19" (W), 4.4cm (H) x 14.6cm (D) x 48.26cm (W) |
D/A Dynamic Range |
112 dB A-weighted, 110dB unweighted |
|
Full-featured Speaker Processing in a 1U Space
Speaker processing can be a complicated business requiring a substantial array of equipment, but the Yamaha SP2060 offers everything you need in a single rack space. This innovative 24-bit, 96-kHz digital speaker processor delivers excellent sound quality, an impressive variety of processing functions — gain, delay, PEQ, comp, crossover, limiter, and an all-pass filter for phase adjustment — and intuitive programming from Yamaha's DME Designer application running on a personal computer. It has two analog inputs and six analog outputs, plus two AES/EBU format digital inputs for connectivity with a broad range of systems. And if you use Yamaha Installation Series Speakers, all you need to do is select one of the many optimized presets provided for great sound with minimum measurement and setup time. The SP2060 is a compact, portable 1U unit that is ideal for live sound or installations.
Sampling Frequency | Internal Clock | 96kHz | External Clock | Normal Rate | 44.1, 48kHz (±0.1%) | Double Rate | 88.2, 96kHz (±0.1%) | Signal Delay | 761µsec Input to Output, fs = 96kHz | Frequency Response | 20Hz -40kHz (TYP 0dB, MAX +0.5dB, MIN -1.0dB), fs=96kHz, RL=600ohms | Total Harmonic Distortion | 0.007% (+22dBu@1 kHz),
0.05% (+4dBµ@20 Hz - 40kHz)
fs=96kHz, RL=600ohms;
measured with 18dB/octave filter @80kHz | Hum & Noise | TYP -82dBu,
fs=96kHz, RL=600ohms, Rs=150 ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞ dB/octave attenuation. | Dynamic Range | 106dB AD+DA
fs=96kHz, RL=600ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞dB/octave attenuation. | Crosstalk @1kHz | -80dB INPUT to Output
fs=96kHz, measured with 18dB/octave filter @80kHz | Power Consumption | 30W | Dimensions (W x H x D) | 480 x 44x 360.2mm | Net Weight | 4.2kg |
| Advanced Feedback Suppression Processor with Full LCD Display
The AFS2 Dual-Channel Advanced Feedback Suppression Processor from DBX protects your ears and audio equipment from annoying and potentially damaging audio feedback without altering your sound. The AFS2 features application-specific filter types for speech, music low, music medium, and music high. The 24 fixed or live narrow-band notch filters are capable of removing frequencies at 1/80 of an octave, ensuring an optimal frequency response without the possibility of feedback.
The front panel features the wizard function to take the guesswork out of setting up any room by incorporating an advanced feedback suppression module and providing a full LCD display for system settings and menus. Additionally, the AFS2 offers a five-segment LED for accurately monitoring input levels for each channel, while the notch filter indicator allows you to monitor the number of filters applied. Dedicated bypass buttons are included to help isolate problem channels. The rear panel offers XLR and 1/4" inputs and outputs, both switchable between +4 and -10 dB operations. A USB port has been provided for firmware updates. The AFS2 ships with a standard IEC power cable.
Number of Channels |
2 |
Inputs |
Connectors: Female XLR and 1/4" TRS
Type: Electronically balanced and unbalanced, RF filtered
Impedance: Balanced 50 kohm, unbalanced 25 kohm
Max Line Level: +20 dBu |
Input CMRR |
>40 dB, typically >55dB @ 1 kHz |
Outputs |
Connectors: Male XLR and 1/4" TRS
Type: Electronically balanced and unbalanced, RF filtered
Impedance: Balanced >120 ohms, unbalanced >60 ohms
Max Level: +20 dBu |
A/D/A Converter |
A/D Converter: DBX type IV conversion system
A/D Dynamic Range: >113 dB A-weighted, >110 dB, unweighted, 22 kHz BW
Type IV Dynamic Range: >119 dB, A-weighted, 22 kHz BW; >117 dB, unweighted, 22 kHz BW
A/D Conversion: 24-bit
Sample Rate: 48 kHz
D/A Dynamic Range: 112 dB A-weighted, 109 dB unweighted
D/A Conversion: 24-bit |
Dynamic Range |
109 dB A-weighted, 106 dB unweighted, 22 kHz BW |
THD + Noise |
0.003% typical at +4 dBu, 1 kHz |
Frequency Response |
20 Hz to 20 kHz, ±0.5dB |
Crosstalk |
Interchannel Crosstalk: >80 dB typical
Crosstalk Input to Output: >80 dB |
Power |
US: 100 to 120 VAC 60 Hz
EU: 220 to 240 VAC 50 Hz
9 W |
Dimensions (HxDxW) |
1.8 x 5.8 x 19.0" / 4.4 x 14.6 x 48.3 cm |
Weight |
4.5 lb / 2.0 kg |
|
Reviews
There are no reviews yet.