DRAWMER DS501 – Power Gate

The DS501 is a sophisticated dual channel noise gate with fully tuneable \'Peak Punch\' incorporating a number of features pioneered by Drawmer, which are invaluable to the sound engineer, and not found on conventional noise gates.

• \'Tuneable\' Peak Punch.
• Variable high pass and low pass filters for \"frequency conscious\" gating.
• Comprehensive envelope control, attack, hold, decay, and range.
• Key input for external triggering.
• \"Key Listen\" facility.
• Extremely fast attack time, to preserve the natural attack of the sound.
• Balanced inputs and outputs.
• Stereo linkable.
• Can be used for \"Gating\" or \"Ducking\".
• High audio specification.

Positioned in the Drawmer range over the industry standard DS201 Dual Gate, the DS501 Power Gate features a new dual mode ‘tuneable’ Peak Punch processing section on each channel. In tuneable mode a fully variable frequency selector with a range from 75Hz to 16kHz allows the user to shape the transients of the gated signal and ‘tune-in’ to the particular area of the audio spectrum where the Peak Punch is to be active. In addition a variable ‘more’ control allows the user to tailor the amount of processing. A secondary Full Band Peak Punch mode is also available.

Designed principally for drum and percussive gating applications, tuneable Peak Punch makes it possible to add transient punch to frequencies lacking in individual drum sounds, adding greater definition and presence to the gated signal. Using low frequency Peak Punch adds depth to thin drums, whilst higher frequency Peak Punch can dynamically emphasise rim shots or the ‘crack’ of a snare drum. Setting up noise gates can be tedious and unrewarding. For example, when attempting to separate a signal from unwanted noise or crosstalk that is relatively high in level, spurious triggering of the gate by unwanted components within the sound can be a serious problem. This can often be experienced in the studio when recording a drum kit. If a gate is used to clean up the snare drum sound it is quite likely that the nearby hi-hats will spill into the snare drum microphone and cause the gate to open. Increasing the threshold level may cure this problem, but then there is a very real danger that any quieter snare drum beats may not cause the gate to open at all and the performance can easily be ruined.

The DRAWMER solution to this problem is the inclusion of two variable filters, one high-pass and one low-pass, which act upon the side-chain keying circuitry. By setting the output switch to key listen the user can hear the action of the filters and adjust them to reject high frequency spillage from the hi-hats. This now enables the gate to only open on the lower frequencies present in the snare drum.

The very fast attack of the DS501 means that it can open in a matter of micro seconds, thus preserving the natural attack of whatever sound is being gated and the comprehensive envelope controls mean that the gain can be changed at whatever rate best suits the material being processed. With vocals for example, a fairly fast attack is needed so as not to clip the leading consonants but a slower release time will prevent the end of words being clipped off and will also fade out any noise gradually rather than cutting it off abruptly. This latter point is very important as the human ear is far more sensitive to rapidly changing noise levels than to a constant low level noise.

Another important role played by the gate is in the reshaping of existing sounds. An example of this might involve a simple sampling delay line used to store a sound to be re-triggered later and added to a mix. A gate can be used to impart a slower attack or faster decay to the sound and careful setting of the decay envelope can effectively hide any noise present at the end of the sample. When using a sampler or drum machine the gate can be considered a triggered envelope shaper, and the wide range allowed by the envelope controls make the DS501 ideal for this application.

The unit can be switched to accept a key input, which allows the gate to be triggered externally. An example of this would be to use a snare drum signal to open the gate on a separate ambient microphone to create a natural alternative to gated reverb.

Each channel can be individually switched from Gating to Ducking for \'voice over\' applications or the removal of \'clicks\' and \'pops\'.

Psychoacoustic Bass Enhancement Unit with Renaissance Compressor, MaxxBass, and L2

Bass Boost for Live Sound, Broadcast, Mastering & Post Production
They say that in electronics there's no new technology - the only changes
will be in size and applications. Things will simply keep getting smaller
while doing more. This is certainly true in music (just think about what an
iPod can do), but as we design smaller playback systems with small speakers,
there are also some tradeoffs, particularly in music. Clever cabinet designs and
high-excursion drivers can get you only so far. Any audio engineer trying to extract
bass from real-world components must eventually face the laws of physics:
All things being equal, small boxes and speaker cones can't move enough air
to produce a room-shaking low end. When working with systems tiny enough to
toss in a shoulder bag, the challenge is even more formidable. Interestingly enough,
Waves MaxxBCL has a new solution to this problem using a very old concept.

Waves MaxxBCL at a Glance:
MaxxBass? Bass Enhancement adds deep bass sound without adding bass frequencies
Waves Renaissance Compressor
L2 Ultramaximizer Peak Limiter
24-bit/96kHz resolution with 48-bit, double-precision processing
Supports optical, coaxial S/PDIF, AES/EBU, balanced and unbalanced line-level analog signals

MaxxBass Bass Enhancement
Waves' patented algorithm adds stunning bass sound without adding bass frequencies,
delivering a bigger bottom end. MaxxBass? allows your audience to hear bass frequencies
lower than physically present by applying psychoacoustic principles: Even though we
can hear a bass guitar from a small speaker, we don't actually hear the fundamental
frequency because the speaker can't produce a pitch that low. Instead, we hear the
harmonics that the speaker can produce, and this causes the brain to create the "missing
fundamental." MaxxBass? takes this well-known psychoacoustic phenomenon to the
maximum, giving you the ability to extend the perceived frequency response of a system
about two octaves below its physical limitation.
To accomplish this, the signal is split: high frequencies are passed to the output (to be
added back to the bass). The bass signal is analyzed and a specific series of upper
harmonics are created. Because the dynamics of the original bass are duplicated in these
harmonics, the result is the most natural sounding bass enhancement available. The
MaxxBass? harmonics and the original bass can be mixed in any proportion at the output.
To provide more control, a high-pass filter can be switched in, allowing the harmonics only to
be passed along as an "image" of the original bass frequencies, which is useful when working
with a system with known low-frequency limitations to avoid over-excursion of the speaker drivers.

Renaissance Compressor
Designed to provide the classic warm sound of analog compressors, the legendary
Renaissance Compressor controls dynamics with studio-style warmth that flatters
full mixes, vocals, or instruments. Controls include selection of vintage-style Opto
or modern Electro compression, and threshold, ratio, and attack controls. Waves
ARC? (Automatic Release Control) algorithm dynamically optimizes the compressor's
release value for a wide-ranging input. ARC? reacts much the way a human ear
expects, and can produce increased RMS level with greater clarity.
In general, the release is faster for peak transients and slower for the overall RMS
level. The ARC? system varies the release time to fit the ear's expectations while
increasing RMS, and without creating distracting artifacts. In this way, the
Renaissance Compressor can serve as a leveler plus a fast compressor simultaneously.

L2 Ultramaximizer Peak Limiter
Heard on countless hit records and soundtracks, the L2 Ultramaximizer puts sound
up-front with breathtaking transparency. The L2 is capable of a very fast, overshoot-free
response. Once the limiter threshold has been set, you can define the actual peak level
that the processed signal will reach. Once set, limiting and level re-scaling becomes a
one-shot process. The L2 can significantly increase the average signal level without
introducing any audible side effects. Yet there is plenty of range to recreate "vintage"
effects such as level pumping or severely limited dynamic range if you like.

Pristine Sound Quality
The MaxxBCL offers 96kHz, 24-bit resolution with a 48-bit, double precision internal
processing path and a dynamic range of ~125dB. The totally passive analog input
path to the ADC uses Jensen transformers, while the output path also features Jensen
analog output transformers. The unit is galvanic-isolated, which prevents ground loops
and allows it to operate in electrically unstable environments. Waves MaxxBCL combines
the highest quality converters available with unequalled processing algorithms to offer you
astonishing new power in bass enhancement, dynamics processing, and format conversion
(analog-to-digital, digital-to-analog, and digital re-quantization).

Versatile Connections
The MaxxBCL supports optical, coaxial S/PDIF, AES/EBU, balanced and unbalanced
line-level analog signals. MaxxBCL features a unique set of input and output trim settings:
analog input headroom can be set from 9dB above 0dBu to 24dB in six precise steps
(using the rear-panel selectors). Analog output level is similarly set with a separate
rear-panel trim pot offering you the ability to connect between devices with a wide range
of input and output levels.

Waves MaxxBCL Features:
User Interface:
Clear backlit displays, meters, and buttons are visible in all lighting conditions
THD + Noise: ? 0.0006 % @ 1kHz @ -1dBFS
Precision metering with resettable peak hold options (2 sec, infinite)
Accurate, wide-range metering covering 90dB for input and output
and 12dB for compressor and limiter attenuation
Quick access independent bypass on each processing block
Tactile feedback knobs
Four easy store/recall user presets
Input / Output:
Analog, AES/EBU, S/PDIF
Independent rear-panel input and output headroom calibration in six steps
(+9, 12, 15, 18, 20, and 24 dBu)
Passive analog inputs to the A-to-D converters using Jensen analog input transformers
Jensen analog output transformers
High-performance IDR dithering to 16- or 24-bit output
Precise input level setting using 1% resistor networks
Processing:
48-bit end-to-end internal processing path
Switchable compressor/MaxxBass? order
MaxxBass:
Adjustable processor frequency from 25 to 120Hz
Adjustable harmonic mix percentage from 0 to 100%
High-pass Filter "harmonics only" option
Compressor:
Opto/Electro mode selection
Threshold (0-60dB), Ratio (1:1-12:1), and Attack (0.5, 1, 2, 5, 10, 20, and 50 ms) controls
Proprietary ARC? Automatic Release Control
Automatic gain makeup
Limiter:
Overshoot-free look-ahead processing
Adjustable Threshold (0-18dB)
Adjustable Output Ceiling (0-18dBFS)

Innovation

The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter
designed for use in any professional audio dynamics control application.
Multiple Modes
The Afterburner can be set up and used in three different ways:
In Two channel mode, it performs as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain. In stereo
mode, our New Adaptive Stereo Link circuitry provides increased stereo
imaging accuracy when linking both channels as a stereo pair. A single front
panel switch puts the Afterburner into its alternative Mono mode, setting it up
as a Single channel, Dual Band compressor/limiter, with separate dynamics
control of both Low and High frequencies, opening up a whole new range of
gain control techniques.
Enhance Switch
In any mode, the Afterburner features an 'Enhance' switch, which provides
frequency restoration to preserve the spectral balance of the audio signal,
compensating for the sagging Low and High frequency response of compressed
program material. Think of it as a 'smart' loudness control.
 
Features
Switchable Modes - Stereo; Dual Channel Single band; or Single Channel
Dual Band (Low and High)
Low and High frequency compression in Single Channel mode
'Enhance' switch restores spectral balance of compressed signal
New Hard/Soft knee compression switch
New Adaptive Stereo Link circuit for accurate stereo imaging
New Above/Below Threshold LEDs enable at-a-glance compression
confirmation
Balanced XLR and Jack Inputs and Outputs
Sidechain Insert points
Intuitive user-friendly layout
Flawless performance
 
New Above/Below Threshold LEDs enable at-a-glance compression confirmation
New Hard or Soft knee compression option
New LED metering provides accurate Level status, with separate Gain Reduction
metering in easy to read 'wide scale' meters. There is also comprehensive LED
indication of all operating functions and status in any mode.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. As well, each channel has a TRS jack
Sidechain access insert point, for applications such as De-essing (when used with
an external equalizer such as the ARX Multi Q or EQ 260).Other features include a
true Hardwire bypass switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner
is equally at home in Studio, Installation, Broadcast and Sound Reinforcement
environments. It can provide great sounding dynamics control effects that are not
available with any other device.
 
T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 115 dB
Sidechain Insert Impedance 10 Kohm
Filter Section
Filter Type Phase corrected 6dB/octave
Summed Filter Response ±0.2dB through crossover region
Dividing Frequency 250 Hz
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Sidechain Insert Connector TRS Jack

Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
Above/Below Threshold LEDs
12 segment LED Output Level display
Numbered marker panel for labelling compressor assigns
7 segment LED Gain Reduction display
Enhance switch and status LED
Adaptive Stereo link switch and status LED
Dual/Single channel mode switch and status LEDs
Rear Panel Connectors
Balanced Inputs and Outputs, on both XLR and TRS jack
connectors. In Single channel (Mono) mode, use Channel
1 Inputs and Outputs only
Sidechain Insert TRS connector on each channel
AC input connector, with voltage switch and fuse.
 

The S com 4 is a compact and versatile single-rack space device that provides
four channels of high quality dynamics processing with an Expander/Gate and
Compressor/Limiter on each channel.
The four channels operate independently or in stereo pairs. Its multi-segment LED
metering displays input/output level as well as gain reduction. The Expander/Gate
section features a continuously variable Threshold control as well as a switch for
fast or slow release times.
The Compressor/Limiter section includes variable Threshold, Ratio and Output levels.
S com 4's Enhancer switch restores high frequencies that are sometimes diminished
by heavy compression. This wide-ranging combination of features makes the S com
4 an efficient and versatile audio tool for a wide variety of applications. Its clean and
quiet audio characteristics make it ideal where high sonic integrity is imperative. 
 
FEATURES:

4 Channel Compressor/Limiter, Expander/Gate with Enhancer
Linkable in two Stereo pairs
Expander/Gate with variable Trigger control and switchable Fast/Slow Release
5 Segment LED meters for Input/Output levels and Gain Reduction on each channel
Advanced circuit design utilizing Low Noise Operational
Amplifiers and High Quality VCA's
Servo Balanced Inputs and Outputs on XLR and 1/4" connectors
SKD (Smart Knee Detector) circuit automatically switches from soft to hard knee
based on the level of Input signal applied
Individual Threshold and Ratio controls on each channel
Three-year extended warranty 

Features
Unique High Density design puts SIX gates in
minimum rack space
Intuitive, 'user friendly' layout
Balanced Inputs and Outputs
Fast, low noise opto-coupler circuitry
Sidechain/Key Input points on each channel
Hardwire Bypass switch on each gate
Flawless performance in any audio environment

The sheer amount of effects and signal processors required for today's
standards of audio production puts a great strain on the available space
in equipment racks, both in the studio and on the road.
So, in order to give engineers more control in less space, we've created
the ARX Sixgate; Six full function noise gates neatly housed in a compact,
all steel 1 RU package, without sacrificing features or quality.
Why Six gates?
Research shows that the majority of noise gates get used on drum kits,
which means using typically 5 to 6 gate channels. Compare this to the
two or maybe 4 channels that most other units have, and you'll see the
reason for the Sixgate's success.And, by using a minimalist approach to
drum gates, the ARX Sixgate has enough gates left over for backing vocals
and other instruments.
Industry Standard controls
Front panel controls for each gate consist of the 'Industry Standard' controls
for Release, Depth and Threshold, plus Red and Green LED displays to indicate
Gate Open or Closed status, and an IN/OUT hardwire bypass switch.
In addition to this, each gate has a blank panel to write on for easy confirmation
of gate assigns. No more pieces of masking tape stuck everywhere!
Ultra Low Noise
Internally, each gate has proprietary ARX ultra low noise high-speed opto-coupler
circuitry with program dependent Attack time, which tracks the incoming signal to
automatically determine optimum gate response.
Balanced Inputs and Outputs
The rear panel features true differential Balanced Inputs and Outputs for each gate,
on insulated TRS jack connectors.Each gate channel also has Individual Key Inputs/
Sidechain access insert points which can be used either for gate control by an external
signal, or for frequency sensitive gating (when used in conjuction with an external
equalizer such as the ARX EQ260).
Universal AC Power
AC power range on the Sixgate is a universal 100 to 120V or 220 to 240V, and is
connected to the unit via a standard 3 pin IEC connector, with built-in fuse and voltage
switch.
The Sixgate's unique combination of High Density design, intuitive 'user friendly' controls,
and clean uncluttered layout make it a truly useful audio tool for all applications.

T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance
Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise Ratio
Gate Closed: -95 dB Unweighted, -105 dB 'A' weighted
Gate Open, Depth Minimum: -93.5 dB Unweighted -98dB
'A' weighted
Distortion 0 .01% THD @ 0dB,1KHz
Dynamic Range 125 dB
Attack Time Program dependent using high-speed
opto-couplers
Release Time User variable
Input and Output Connector type Balanced Jack
Sidechain Insert Connector TipRingSleeve Jack
Sidechain Insert Impedance 10 Kohm
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“Wide x 13/4“High x 6“Deep; 482 x 44 x 155mm

Front Panel Controls
Individual Release, Depth and Threshold controls
Hardwire bypass IN/OUT switch
Open/Closed gate status LED
Marker panel for labelling gate assigns
Rear Panel
Balanced Inputs and Outputs, on Balanced jack
connectors
Sidechain Insert/Key Input TipRingSleeve jack on
each channel
AC input connector, with voltage switch and fuse 

VIRTUALIZER 3D FX2000
High-Performance 3D Multi-Engine Effects Processor
71 breathtaking new algorithms—true RSM (Real Sound Modeling) stereo and 3D effects
Wave-adaptive virtual Room reverb algorithms for natural reverb and delay
Awesome modulation, dynamic, psychoacoustic and EQ algorithms
Authentic amp simulation, distortion and special effects
11 effect combinations with selectable serial / parallel configuration
Up to 7 adjustable parameters plus 2-band EQ per effect
24-bit A/D and D/A converters with 64/128-times oversampling
True stereo processing for realistic channel separation in stereo image
100 factory presets plus 100 user memory locations
Extensive MIDI implementation
Accurate LED level meters for perfect level setting and optimum performance
Servo-balanced XLR and ¼'' TRS inputs and outputs
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany

 Reverbs & Delays

Because it is one of the most desired effects, the FX2000 provides 12 different reverb programs, so you always have the ideal reverb for your live performance or studio needs.

Reverbs include:

    CATHEDRAL
    GOLD PLATE
    SMALL HALL
    ROOM
    STUDIO
    CONCERT
    STUDIO
    STAGE
    SPRING REVERB
    AMBIENCE
    EARLY REFLECTIONS

Specialty reverbs include:

    REVERB – reverb is synthetically turned off after a predetermined amount of time
    REVERSE REVERB – reverb envelope is reversed—it slowly gets louder

Delays include:

    STEREO DELAY – delay is processed across the entire stereo image
    TAPE ECHO – simulates classic tape echo devices, pre-dating the advent of digital delays
    PING PONG – delay signal is "bounced” from left to right at an adjustable tempo

Much More than Just Reverb and Delay

The FX2000 has some of the best-sounding reverb and delay programs, but thatʼs not all. It also provides excellent modulation effects (such as chorus, flanger and phaser), including special variations like musical pitch shifter, tremolo and even a rotary speaker simulation.

Modulation and Pitch Shifter FX:

    STEREO FLANGER (originally generated by playing back two synchronized "reel to reel” tape recorders with a finger rubbing on the flange of one of the take-up reels)
    VINTAGE FLANGER simulates a guitar fl anger stomp box
    JET STREAM FLANGER sounds like a classic analog flanger
    STEREO CHORUS (combines a slightly detuned signal with the original)
    ANALOG CHORUS simulates a guitar chorus stomp box
    VINTAGE CHORUS imitates a classic analog studio chorus
    ULTRA CHORUS creates the sound of an eight person chorus
    STEREO PHASER (combines a second, phaseshifted signal to the original)
    VINTAGE PHASER represents a guitar phaser stomp box
    DUAL PHASER processes the left and right channels separately
    ROTARY (simulation of the rotating speakers typically used on an organ) – Slow or Fast
    PITCH SHIFTER (changes the pitch of the original signal) – can be used to create harmonies with the original signal or replace it entirely with the altered pitch. Choices include stereo, two and three vocal pitch shifter
    VIBRATO – the peak frequency of the tone is periodically and uniformly changed (quickly or slowly)
    TREMOLO (common vintage guitar amplifier effect) – a fast or slow periodic variation in volume
    AUTO PANNING – signal is automatically sent from one side of the stereo image to the other, either once or multiple times

Dynamic FX:

    COMPRESSOR – reduces the dynamic range of the signal, maintains consistent signal level and thus avoids distortion associated with excessive input levels
    EXPANDER – effectively broadens the dynamic range of source signals while reducing background noise
    GATED REVERB – helps reduce background clutter by turning reverb off below a predetermined threshold level. Particularly effective on drum mics and vocals
    ANA. KOMPR/LIM. — similar to COMPRESSOR but with Limiting functionality
    ULTRAMIZER – analyses incoming signal and automatically applies compression across two independent frequency bands
    DENOISER – eliminates or reduces noise and other interference
    DE-ESSER – reduces or removes sibilance (Ssss sound) from signal
    WAVE DESIGNER – allows you to influence the envelope by adjusting Attack and Release of the signal

Psychoacoustic FX:

    EXCITER – adds artificially generated overtones to the original signal, increasing presence and perceived loudness without significant increase in signal level
    ENHANCER – functions much like a dynamic pitch equalizer
    ULTRA BASS – sub-harmonic processor combined with bass exciter and limiter
    STEREO IMAGER – divides the signal into middle and side signals, allowing individual signals to be amplif ed when desired and placed on the stereo image
    ULTRA WIDE – creates a broader stereo image
    BINAURALIZER – also creates a broader stereo image and compensates for crosstalk between both speakers

Filter/EQ FX:

    AUTO FILTER – influences the frequency response of a signal. Two filters are included: low pass allows low frequencies to pass and suppresses high frequency content; high pass does the exact opposite
    LFO FILTER - Controls the rate of oscillation effects
    PARAMETRIC EQ – allows you to control the bandwidth, frequency and amplitude of a signal
    GRAPHIC EQ – the sound spectrum is divided into eight (8) adjacent frequency bands, which can be cut or boosted, bandwidth is predetermined

Distortion FX and Amp Simulations

The FX2000 is also equipped with distortion, amplifier and speaker simulation including VOCAL DISTORTION, TUBE DISTORTION, GUITAR AMP, TRI FUZZ, SPEAKER SIMULATION, RING MODULATOR and LO-FI.

Special FX:

    VINYLIZER – adds clicks and/or noise to the signal, reminiscent of old vinyl records and tape machines
    SAMPLER – allows you to record and playback up to five (5) seconds of program material
    VOCODER – allows the input signal to modulate another signal (usually a synthesizer sound), creating the familiar "talking synthesizer” effect
    VOICE CANCELER – removes mono vocal parts from stereo recordings for "instant Karaoke”
    RESONATOR – simulates and oscillating system that amplifies a specific frequency

Our FX Combinations Go to 11

Sometimes you want to add a little (or a lot) of color to your reverb and delay patches. The FX2000 allows you to layer modulation effects like chorus, flanger, pitch or tremolo with your reverb or delay selections.

FX Combinations include:

    Chorus & Reverb
    Flanger & Reverb
    Leslie & Reverb
    Pitch & Reverb
    Delay & Reverb
    Tremolo & Reverb
    Phaser & Reverb
    Chorus & Delay
    Flanger & Delay
    Pitch & Delay
    Tremolo & Delay

Enhanced User Editability
Logical grouping of parameters, along with the combination of encoders, buttons, LEDs and an easily readable LED display, make operating the FX2000 a breeze. You are free to edit up to seven parameters per preset, and then save them for future use in the 100 provided memory locations.
Value
With its extremely powerful processing capability and versatile array of features, the FX2000 will become the busiest tool in your audio arsenal. Stop by your BEHRINGER dealer today and find out why more professional sound engineers are turning to the FX2000 as their primary FX processor— both in the studio and on the road.