650W ΤΕΛΙΚΟΣ ΕΝΙΣΧΥΤΗΣ (100V)
INPUTS: RCA + XLR
OUTPUTS: 70V+100V+4-16 Ohm
ΕΝΔΕΙΚΤΙΚΑ LED: LEVEL-CLIP-PROTECTION-TEMPERATURE
Crown CDi 1000 2x700W-4Ω Power Amplifier
The Crown? CDi 1000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply.
The outputs shall be usable as dual or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker. Dual connectors shall work with 2-8 ohm or
70V loads. Bridge-mono connectors shall work with 4-8 ohm or 140V loads.
HiQnet USB Connector: Type B, connects to a USB port on a PC.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Dual (per channel): 700W with 1% THD, 4 ohm Dual (per
channel): 500W, 8 ohm Dual (per channel) 275W, 4 ohm Bridge-Mono: 1,400W
with 1% THD, 8 ohm Bridge-Mono: 1,000W, 70V Dual (per channel): 500W.
Voltage Gain at 1kHz, 8 ohm rated output: 30.5 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
AC Line Current: 6.5A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave and Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB
bandpass gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 20 presets. 19 are user-definable.
Protection shall include the following:
CDi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg).
The amplifier shall be designated the Crown CDi 1000.
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
|Specification || |
|Power Source ||220 - 240V AC or 24V DC |
|Rated Output ||120W |
|Power Consumption ||124W (EN60065), 260W(AC operation at rated output, 8A (DC operation at rated output) |
|Frequency Response ||50 - 20,000Hz (+/- 3 dB) |
|Distortion ||Under 1% at 1kHz,1/3 rated power |
|Input ||MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) |
|Output ||SPEAKER OUT:Balanced (floating) |
HIGH IMPEDANCE:83W (100V)
LOW IMPEDANCE: 4Ω (22V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack
|Phnatom Powe ||DC + 21V (MIC 1) |
|S/N Ratio ||Over 60dB |
|Tone Control ||Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz |
|Muting || MIC1: Mutes other signals by 0 - 30 dB attenuation |
|Indicator || Power signal, peak |
|Finish ||Panel: ABS resin, black/Case: Steel plate, black |
|Dimensions ||420 (W) x 100.9 (H) x 360.3 (D) mm |
|Weight || 10kg|
The A-1700 Series of high-performance mixing-dedicated power amplifiers are ideal for PA applications that value versatility. Specifically designed to satisfy the multi-microphone public address requirements of environments such as places of worship and meeting halls, the A-1700 Series Microphone Mixing Amplifiers focus on operational flexibility as well as advanced functions, proving an ideal cost-effective PA solution.
|Specification || |
|Power Source ||AC mains 50/60Hz) |
|Output ||120W |
|Power Consumption ||258W (rated output), 105W (EN60065) |
|Frequency Response ||50 - 20,000Hz Â±3dB |
|Distortion ||Under 2% at 1kHz, rated power |
|Input ||MIC 1 - 6: -60dB*, 600Î©, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack |
AUX 1 - 2: -20dB*, 600Î©, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack
(Either MIC 5 or AUX 1, and either MIC 6 or AUX 2 selectable)
AUX 3 - 4: -20dB*, 10kÎ©, unbalanced, RCA pin jack
AUX 5: -20dB*, 10kÎ©, unbalanced, combined type of XLR-3-31 equivalent and phone jack
PWR AMP IN: 0dB*, 600Î©, unbalanced, RCA pin jack
An equalizer or other signal processor connectable between LINE OUT and PWR AMP IN terminals)
|Output ||REC: 0dB*, 600Î©, unbalanced, RCA pin jack |
LINE: 0dB*, 600Î©, unbalanced, RCA pin jack
SPEAKER SELECTOR: 2 zone, high impedance
(100V line/83Î©), individual selector key, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/83Î©),M4 screw terminal
Low impedance (4 - 16Î©), M4 screw terminal
(Both Low and High impedance terminals cannot be used at the same time.)
|Phantom Power ||ON or OFF for each MIC 1 - 6 with switch setting |
|S/N ratio |
(Band Pass: 20 - 20,000Hz)
|Over 100dB (Master volume: min) |
Over 76dB (Master volume: max)
Over 60dB (MIC 1 - 4))
Over 53dB (MIC 5, 6)
Over 76dB (AUX 1 - 5)
|Tone Control ||Bass: Â±10dB at 100Hz, Treble: Â±10dB at 10kHz |
|Control Input ||REMOTE VOLUME: M3 screw terminal |
POWER REMOTE: No-voltage make contact input, open voltage: 24V DC (when the unit's power is OFF), short-circuit: under 10mA, M3 screw terminal
|Indicator ||5 point LED output level meter, |
Power indicator LED,
Zone indicator LED
|Operating Temperature ||-10ºC - +40ºC |
|Finish ||Panel: ABS resin, black, hair line |
Case: Steel plate, black
|Dimensions ||420 (W) x 107.7 (H) x 367 (D)mm |
|Weight ||12.6kg |
|Accessory ||Power cord x 1, |
Terminal block cover x 1,
Terminal block cover mounting screw x 2
|Option ||Rack mounting bracket: MB-25B, |
Volume control cover: YA-920.
| ||Note* Note: Distance between barriers on the above screw terminals; M3 = 7mm, M4 = 9mm |
| ||* 0dB = 1V ||Weight||21.50||10.00||10.00||12.60||0.50||1.10|