DYNACORD SUB-118 Subwoofer 500 Watts

Discontinued

1,515.65 incl. GR VAT

Out of stock

CompareAdd to wishlist Submit Better Price
DYNACORD΄s SUB 118 is a vented direct radiating cabinet, equipped with the high-power DYNACORD LFS 18700 transducer. The new patented High-Speed-Laminar-Vent system shows signifi cantly less distortion and lower air noise at low frequencies than common vented cabinets. The SUB 118 contains a passive fi lter that suppresses high frequencies. Appropriate fullrange cabinets, e.g. DYNACORDʼs […]

 

Read more

DYNACORD΄s SUB 118 is a vented direct radiating cabinet, equipped with the high-power DYNACORD LFS 18700 transducer. The new patented High-Speed-Laminar-Vent system shows signifi cantly less distortion and lower air noise at low frequencies than common vented cabinets. The SUB 118 contains a passive fi lter that suppresses high frequencies. Appropriate fullrange cabinets, e.g. DYNACORDʼs D15- 3, can therefore be directly connected in parallel to the SUB 118 if an extended bass reproduction is required. You just have to connect the SUB 118 and the fullrange cabinet with a regular Speakon cable. The cabinet is equipped with an electronic circuit called VOICE COIL TRACKING PROTECTION. This circuit senses the terminal voltage of the transducer and simulates the thermal behaviour of the woofer΄s voice coil. In case of potential thermal overload the power applied to the speaker is reduced to a safe level. Extremely powerful amps can be used in order to have maximum dynamic range without the danger of thermal overload in non-controlled situations. The VOICE COIL TRACKING PROTECTION exhibits “soft” switching characteristics, so no annoying clicks or pops are audible. The circuitry automatically resets after the voice coil temperature has reached a safe value. The SUB 118 cabinet is made of 18mm birch plywood. All corner joints and braces are grooved and glued. The cabinet΄s surface is painted with a 2-K laquer fi nish . The acoustic foam front on a powder coated steel grille protects the SUB 118 against damage during transport and bad environmental conditions. The connector panel uses two 4-pole Speakon connectors (INPUT/THRU) for a safe connection and easy daisy-chaining to other cabinets. The pin assignment is 1+/1-. Pins 2+ and 2- are also connected between the two Speakon connectors. A recessed pole-mount fl ange allows easy speaker-on-a-stick applications. Please always take care that every speaker stack has been mechanically secured against accidental falling down. Please always consult a certifi ed structural engineer for correct and safe setup methods. The cabinet is equipped with eight large rubber feet. Four handles and four heavy-duty castors on the rear side guarantee easy and safe transport.

Weight 50.00 kg

Reviews

There are no reviews yet.

Be the first to review “DYNACORD SUB-118 Subwoofer 500 Watts”

Your email address will not be published. Required fields are marked *

Quick Comparison

DYNACORD SUB-118 Subwoofer 500 Watts removeJBL ASB 6128V SUB(V FOLDED) 2x18'1600W removeELECTRO VOICE ELX118 Subwoofer 600 W removeAMERICAN AUDIO SENSE-18B SUBWOOFER IN WOODEN CABINET 18'' 600W / 8 Ohm removeELECTRO VOICE Rx118S 1x18" Subwoofer 600W removeELECTRO VOICE TX1181 500W 18inch Subwoofer remove
NameDYNACORD SUB-118 Subwoofer 500 Watts removeJBL ASB 6128V SUB(V FOLDED) 2x18'1600W removeELECTRO VOICE ELX118 Subwoofer 600 W removeAMERICAN AUDIO SENSE-18B SUBWOOFER IN WOODEN CABINET 18'' 600W / 8 Ohm removeELECTRO VOICE Rx118S 1x18" Subwoofer 600W removeELECTRO VOICE TX1181 500W 18inch Subwoofer remove
Image
SKUSUB-118ASB 6128VE002991E002935001876001920
Rating
Price 1,515.65 incl. GR VAT 3,972.00 incl. GR VAT 585.00 incl. GR VAT597.39 incl. GR VAT1,668.00 incl. GR VAT 1,074.00 incl. GR VAT
Stock

Out of stock

Available on backorder

In stock

In stock

Available on backorder

Available on backorder

AvailabilityOut of stockAvailable on backorderIn stockIn stockAvailable on backorderAvailable on backorder
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

DYNACORD΄s SUB 118 is a vented direct radiating cabinet, equipped with the high-power DYNACORD LFS 18700 transducer. The new patented High-Speed-Laminar-Vent system shows signifi cantly less distortion and lower air noise at low frequencies than common vented cabinets. The SUB 118 contains a passive fi lter that suppresses high frequencies. Appropriate fullrange cabinets, e.g. DYNACORDʼs D15- 3, can therefore be directly connected in parallel to the SUB 118 if an extended bass reproduction is required. You just have to connect the SUB 118 and the fullrange cabinet with a regular Speakon cable. The cabinet is equipped with an electronic circuit called VOICE COIL TRACKING PROTECTION. This circuit senses the terminal voltage of the transducer and simulates the thermal behaviour of the woofer΄s voice coil. In case of potential thermal overload the power applied to the speaker is reduced to a safe level. Extremely powerful amps can be used in order to have maximum dynamic range without the danger of thermal overload in non-controlled situations. The VOICE COIL TRACKING PROTECTION exhibits "soft” switching characteristics, so no annoying clicks or pops are audible. The circuitry automatically resets after the voice coil temperature has reached a safe value. The SUB 118 cabinet is made of 18mm birch plywood. All corner joints and braces are grooved and glued. The cabinet΄s surface is painted with a 2-K laquer fi nish . The acoustic foam front on a powder coated steel grille protects the SUB 118 against damage during transport and bad environmental conditions. The connector panel uses two 4-pole Speakon connectors (INPUT/THRU) for a safe connection and easy daisy-chaining to other cabinets. The pin assignment is 1+/1-. Pins 2+ and 2- are also connected between the two Speakon connectors. A recessed pole-mount fl ange allows easy speaker-on-a-stick applications. Please always take care that every speaker stack has been mechanically secured against accidental falling down. Please always consult a certifi ed structural engineer for correct and safe setup methods. The cabinet is equipped with eight large rubber feet. Four handles and four heavy-duty castors on the rear side guarantee easy and safe transport.

Ηχείο SUB με 2 x 18 2258H NDD neodymium σε V-loaded configuration, 1600W/4Ω. 25Hz-300Hz ±3dB. Parallel/ discrete επιλεγόμενο. Αrrays με AM6315 και AM4315 χρησιμοποιώντας paf-2k planar array frame kit. (967H x 561W x 1215D mm). 89,8kg.

Axial Sensitivity    96 dB
Case Material    9-ply, 15mm Plywood, Internally Braced, with Texured Paint
Frequency Response (-3 dB)    50 Hz - 100 Hz Hz
Frequency Response (-10 dB)    35 Hz - 200 Hz Hz
Recommended High-Pass Frequency    30 Hz
Max. SPL/1m (calc)    134 dB
Coverage
(Nominal -6 dB) H°    Omnidirectional °
Coverage
(Nominal -6 dB) V°    Omnidirectional °
LF Transducer    (1) EVS-18K, 457mm (18”) Woofer
HF Transducer    N/A
Crossover Frequency    N/A Hz
Nominal Impedance (Passive)    8 Ω
Minimum Impedance    6.7 Ω
Connector Type    Dual NL4
Grill    18GA Steel with Black Powdercoat
Height    661 mm (26.02“)
Width    507 mm (19.96“)
Depth    574 mm (22.6“)
Weight Net    31.8 kg (70.11 lbs)
Shipping Weight    35.4 kg (78.04 lbs)

SPECIFICATIONS

- Woofer: 18” AA PA18000, aluminum basket, 100mm Voicecoil
- Power Handling
  600W continuous
  1200W program
  2400W peak
- Recommended input power: 400-800 W @ 8Ohm
- Components: 18” Longexcursion woofer
- Sensitivity (Half Space)
  103dB SPL
  136dB Peak
- Freq. response (-3dB): 42Hz - 200Hz
- Freq. range(-10dB): 36Hz - 250Hz
- Nom. dispersion h x v (-6dB): 90∞x60∞
- Impedance: 8Ohm
- Finish: black structure paint
- Protective Grid: powder coated steel grill with acoustic foam
- Connector: 2x NL4 Speaker
- Handle: 2 handles on the sides
- Pole mount: integrated (M20)
- Cabinet: plywood
- Dimensions (LxWxH): 520x650x600mm
- Weight: 33kg

FEATURE OVERVIEW
- Perfect matched components and enclosure details
- High efficiency
- First class mechanical manufacture for day-to-day operations
- Equipped with optimized 18” LF driver
- Large optional accessory range
- Ideal for mobile and install applications

The EV Rx118 Si 18-inch subwoofer system with 600 watts continuous, 2,400 watt peak power handling. Delivers 126 dB SPL 1 w/1 m (132 dB peaks 1 w/1 m) at full power EVX-180B 4-inch voice coil driver for maximum LF reproduction power with minimum enclosure volume.

Delivers solid bass response to 36 Hz Enclosure is the same width as QRx115 for easy stacking and transportation. Includes 1-3/8-inch stand mount and 30-inch steel pole for use with full range cabinets without the need for extra mounting stands. Enclosure is built from 13-ply, void-free, grain-oriented birch plywood finished with Futura, a sprayed-on polyurethane finish that is very rugged. Available in black or white finishes.

RX118 Features

  • Direct radiating vented design
  • High Sensitivity
  • Solid Bass down to 36 Hz (-10 dB)
  • 2 x four pin Speakon connectors
  • Wheel Kit Available
  • Dimensions: 900mm H x 450mm W x 600mm D
  • Weight: 47.5 kg

The TX1181 is the perfect companion sub to the TX1122 and TX1152 for compact and portable performance. Using the proven EVS18S woofer, the TX1181 effortlessly provides the low-frequency energy needed to keep up with Tour X boxes, as well as many other EV loudspeaker products. The integrated, low-pass input filter allows for single amp drive, and the high-sensitivity and excellent power handling don\'t require a large, expensive amplifier to generate high SPL. 

The TX1181\'s unique Backbone grille not only looks great, but also provides greater strength and damage resistance than simple grille block designs. Proprietary, ergonomically correct handles and angled input panels, and integrated, screw-in-style pole-mount make the TX1181 easy to transport and employ in a variety of applications.

Specifications
Frequency Response (-3dB) 50 - 160 Hz
Frequency Response (-10dB) 45 - 700 Hz
Recommended High-Pass Frequency 30 Hz
Sensitivity 1W/1m 100 dB
Max. SPL / 1m (calc) 132 dB
System Power Handling (continuous/program/peak) 500/1000/2000 Watts
LF Transducer EVS18S
Nominal Impedance (Passive) 8 Ohms
Minimum Impedance 7.5 Ohms
Enclosure Material Plywood and MDF with EVCOAT
Color Black
Flying No
Input Connections Parallel Neutrik® NL4
Internal Crossover Yes
Speaker Type Subs
Weight Net 33.8 kg ( 74.52 lbs )
Dimensions (HxWxD) 769 x 439 x 591 mm
(30.28" x 17.28" x 23.27“)
Weight50.00 kg90.00 kg35.40 kg33.00 kg47.50 kg33.80 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 50.00 kg
Weight 90.00 kg
Weight 35.40 kg
Weight 33.00 kg
Weight 47.50 kg
Weight 33.80 kg