| Content |
CobraNet is a network technology for multichannel transmission of digital audio data. The CM-1 is a compact interface module for NetMax to allow connection to a CobraNet network, which allows the simultaneous transmission of up to 32 digital audio input signals and 32 digital audio output.
* Designed for Cinema, Club Sound, Commercial Sound/Life Safety, Concert Sound, House of Worship, Performance & Sports Venues, Stadium Systems, and other applications.
* 100BASE-TX ethernet interface; 100Mbit/s full-duplex Ethernet interface; IEEE 802.3u compatible.
* Secondary 100BASE-TX Ethernet interface. Second Ethernet interface for the connection of a redundant network to establish fault tolerant systems. Internal audio output interface for the transmission of 32 digital audio channels with 48 kHz sample rate and 16, 20, or 24-bit word length
* Internal audio input interface for receiving 32 digital audio channels with 48 kHz sample rate and 16, 20, or 24-bit word length.
* Control, monitoring, configuration, and firmware updates via Ethernet protocol.
* Status LEDs. Link, activity, fault, and CobraNet conductor status indication via Ethernet connectors.
|
Audio Network CobraNet CM-1 Module (optional)
CAN Bus Interface 2 x RJ-45
Cooling Left-to-right, 3-stage fan
Data Format 24 Bit linear A/D and D/A conversion, 48 Bit processing
FIR-Drive Yes
GPIO Control Port 2 x 6-pole Euro block4 Control Inputs (analog 0 - 10 V / logic control)3 Control Outputs (Relay contact to ground) 1 Fault Output (NC Relay contact) 3 Reference Outputs (+5 V / +10 V/ GND)
Internal Processing 2 DSPs Standard (150 MHz, 300 MIPS)1 DSP per Audio Module (100 MHz, 100 MIPS)DSP-1 Extension Module optional (+300 MIPS)
Network Control (IRIS-Net) Yes
Network Interface Ethernet-10/100 MBit/s, RJ-45
Power Consumption 90 W max. (incl. 2 x AI-1, 2 x AO-1, 1 x CM-1 modules)
Power Supply 100 - 240 VAC, 50/60 Hz
Sample Rate 48 kHz internal
Serial Interface 2 Ports, 9pin D-Sub female (Remote Control)
Signal-to-Noise Ratio (A-weighted) 115 dB
Total Harmonic Distortion 0.01 %
Height 2RU 88.1 mm (3.47“)
Width 483 mm (19.02“)
Depth 381 mm (15“)
Weight Net 7.37 kg (16.25 lbs)
|
The ZonePRO 1261m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.
The 1261m features a total of 12 inputs and six outputs. Inputs include six balanced mic/line switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one S/PDIF input for up to two digital channels. Hardware-controlled
microphone gain allows adjustment of microphone gain per channel.
The 1261m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth®, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.
A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.
The front panel of the 1261m features a power status LED, a network traffic LED, and an RS-232 control port.
Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.
All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).
ZonePRO Designer—the configuration, control and monitoring software for the ZonePRO family of devices—offers control of the ZonePRO 1261m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-bystep configuration process of the 1261m.
SPECIFICATIONS:
Front Panel LED Indicators
Per Output:6 Independent Six-Segment Lightpipe Output Meters that range from -30 to +20 dBu, Threshold Meters
Other:LCD Display provides information about Source Selection, Page Steering, Zone Volume and Mute
Analog Inputs:
12 Total - (6) Balanced Mic/Line Inputs, (4) Unbalanced, Mono-Summed RCA Input Pairs, S/PDIF Input
Type:Euroblock (Mic/Line), RCA (Source)
Impedance (Euroblock):>50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):>25kΩ Unbalanced, RF Filtered
Max. Input Line Level:+20dBu Mic/Line, +12dBu RCA
CMRR:> 40dB, typically >55db @ 1kHz
Mic Pre Gain:30 to 60dB
Mic Input Noise (E.I.N.):< -118dBu, 22Hz-22kHz, 150Ω Source Impedance
Mic Phantom Power:+15VDC
ANALOG OUTPUTS
Number of Outputs: 6 Total
Type:Electronically Balanced, RF Filtered Euroblock
Impedance:120Ω Balanced, 60Ω Unbalanced
Max. Output Level:+20dBu
A/D PERFORMANCE
Type: dbx Type IV™ Conversion System
Dynamic Range line: >113dB, A-weighted, >110dB unweighted
Type IV dynamic range:
>119dB, A-weighted, 22kHz
BW: >117dB, unweighted, 22kHz BW
Sample Rate: 48kHz
D/A PERFORMANCE
Dynamic Range: 112dB A-weighted, 109dB unweighted, 22kHz BW
SYSTEM PERFORMANCE
Dynamic Range: >110dB A-weighted, >107dB unweighted, 22kHz BW
THD+N: 0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response: 20Hz – 20kHz, +/- 0.5dB
Interchannel Crosstalk: >80dB typical
Crosstalk input to
output: >80dB
Propagation Delay 0.8 msec
POWER REQUIREMENTS
Operating Voltage: 100-240 VAC, 50/60Hz
Power Consumption: 27 Watts
BTU: |
- 8ch mic/line input and 8ch analog output
- 16ch YDIF digital I/O
- SD Card Slot for playback
|
The ZonePRO 640m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.
The 640m features a total of six inputs and four outputs. Inputs include four balanced mic/line switchable terminal block inputs and two mono-summed pairs of unbalanced RCA inputs. Hardware-controlled microphone gain allows adjustment of microphone gain per channel.
The 640m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth®, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.
A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.
The front panel of the 640m features comprehensive signal metering, an informative LCD display and user-specified front panel control.
Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.
All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).
ZonePRO Designer—the configuration, control and monitoring software for the ZonePRO family of devices—offers control of the ZonePRO 640m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-by-step configuration process of the 640m.
Front Panel LED Indicators
Per Output:4 Independent Six-Segment Lightpipe Output Meters that range from -30 to +20 dBu, Threshold Meters
Other:LCD Display provides information about Source Selection, Page Steering, Zone Volume and Mute
Analog Inputs:
6 Total (4) Switchable Mic or Line, (2) Unbalanced, Mono-Summed RCA Input Pairs
Type:Euroblock (Mic/Line), RCA (Source)
Impedance (Euroblock):>50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):>25kΩ Unbalanced, RF Filtered
Max. Input Line Level:+20dBu Mic/Line, +12dBu RCA
CMRR:> 40dB, typically >55db @ 1kHz
Mic Pre Gain:30 to 60dB
Mic Input Noise (E.I.N.):
Mic Phantom Power:+15VDC
ANALOG OUTPUTS
Number of Outputs: 4 Total
Type:Electronically Balanced, RF Filtered Euroblock
Impedance:120Ω Balanced, 60Ω Unbalanced
Max. Output Level:+20dBu
A/D PERFORMANCE
Type: dbx Type IV™ Conversion System
Dynamic Range line: >113dB, A-weighted, >110dB unweighted
Type IV dynamic range:
>119dB, A-weighted, 22kHz
BW: >117dB, unweighted, 22kHz BW
Sample Rate: 48kHz
D/A PERFORMANCE
Dynamic Range: 112dB A-weighted, 109dB unweighted, 22kHz BW
SYSTEM PERFORMANCE
Dynamic Range: >109dB A-weighted, >106dB unweighted, 22kHz BW
THD+N: 0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response: 20Hz – 20kHz, +/- 0.5dB
Interchannel Crosstalk: >80dB typical
Crosstalk input to
output: >80dB
Propagation Delay 0.6 msec
POWER REQUIREMENTS
Operating Voltage: 100 VAC, 50/60Hz, 120 VAC, 60Hz, 230VAC 50/60Hz
Power Consumption: 29 Watts
BTU: | The KT-AES50 network module provides a dual port AES50 digital audio interface, compatible with both the Klark Teknik DN9650 and DN9652 Network Bridges and the Midas NEUTRON-NB Dual Network Bridge Expansion Module for the industry-leading NEUTRON High Performance Audio System Engine.
Featuring up to 48 bidirectional channels at both 48 kHz or 96 kHz sample rates, with dual port redundancy in 48 kHz systems, KT-AES50 enables the interconnection of two AES50 networks operating at 96 kHz and 48 kHz respectively, as well as providing expanded AES50 channel counts in either 48 kHz or 96 Hz AES50 networks.
KT-AES50 is designed for simplicity of use, and can operates from the incoming AES50 clock or an external clock via host unit. Panel-mounted LED indicators show the connection status for both AES50 ports.
KT-AES50 is electrically and mechanically compatible with the industry standard Cirrus CM-1 format.
SuperMAC (AES50-Compliant) digital audio networking technology from Klark Teknik simultaneously provides high channel counts, ultra low and deterministic latencies, sample-synchronous and phase-aligned networked clock distribution, error detection and correction, network redundancy, and ease of deployment and use – to meet the demanding requirements of live concert touring.
KT-AES50 is compatible with all Midas digital consoles, audio system engines, digital I/O units, as well as with any other AES50-equipped devices. |
Reviews
There are no reviews yet.