Content |
Clarett OctoPre provides eight specially-designed Clarett mic pres and 24-bit, 192 kHz A-D and D-A conversion that can be used to extend the capabilities of a Clarett interface - or any other interface fitted with ADAT optical inputs and outputs. In addition to the mic pres there are eight channels of D-A conversion providing eight analogue outputs. The eight mic pres feature automatic mic/line switching inputs and two front-panel instrument inputs. Designed specifically for the Clarett range, they offer plenty of gain, yet low noise and distortion - and great sound quality. |
EWI PDI-100 PARA ACOUSTIC DI Box
This is a medium grade professional application Para Acoustic Active DI, which will work well on instruments with passive pickups or active pickups.
The construction is reasonably rugged and the components are well suited for the application yielding results that are typically acceptable for all but the most discerning artists.
The on-board tone and volume controls give the operator a lot of choices in shaping their sound prior to sending the signal to the mix console. This allows an artist to use this device in-place of or in addition to a traditional stage amp for their instrument. This is an excellent choice for IEM bands, or bands that like to keep their stage volume low.
This item is typically used to split the instrument signal going to a stage amp so a feed can be sent also to the mix board, or be used as a stand-alone instrument pre-amp. It is equipped with a ¼” jack for input, a 1/4" jack for output to a stage amp, one XLR jack for the send to the board and a TRS jack for inserting an FX device.Since this is an active D.I. box, it needs to be powered which can be done either with Phantom Power from the mix board, or with the supplied internal 9v battery. The battery is fairly easy to change by removing one screw in the bottom of the case.
|
Mic Inputs
• Frequency response at minimum gain (0dB): -0.35dB at 20Hz and –3dB at 122kHz
• Frequency response at maximum gain (60dB): –2.5dB at 20Hz and –3dB 103kHz
• Gain range: 0dB to +60dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +7.4dBu
• THD+N: 0.0009% (measured at 1kHz -20dBu input signal, at 30dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise EIN: -126dB (measured at 60dB of gain with 150Ω termination and 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -98dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 123dB (relative to max output 25dBu)
• SNR: 120dB (relative to 0dBFS (+22dBu)
• CMRR: 88dB.
• Input Impedance, variable: 600Ω, 1400Ω, 2400Ω, 6800Ω
Line Inputs
• Frequency Response at unity gain (0dB): -0.3dB at 20Hz and –3dB at 94kHz
• Gain range: -20dB to +10dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +25.4dBu
• THD+N: 0.002% (measured with +4dBu input signal, 0dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -91dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 116dB (relative to max output 25dBu)
• SNR: 113dB (relative to 0dBFS +22dBu). Input Impedance: 10kΩ
Instrument Inputs
• Frequency Response at +10dB gain: -0.2dB at 20Hz and 0dB at 200kHz
• Frequency Response at +40dB gain: -3dB at 20Hz and –3dB at 38.4kHz
• Gain range: +10dB to +40dB continuously variable
• Maximum headroom: +11.5dBu
• THD+N: 0.006% (measured with –20dBu input signal, at minimum gain (+10dB), with a 20Hz/22kHz bandpass filter)
• Noise at main output with minimum gain (+10dB): -95dBu (measured with a 20Hz/22kHz bandpass filter)
• Input Impedance = >1MΩ
High Pass Filter
• Roll off = 18dB per octave 3 pole filter
• Frequency range: 16Hz to 420Hz (continuously variable, measured at the 3dB down point)
Meters
• 6 LED meter is calibrated 0dBFS = +22dBu (the maximum level which can be correctly converted by the optional internal A/D converter before overload occurs). The meter calibration points are as follows:
Meter panel calibration value in dBFS / Equivalent dBu value
0dBFS / +22dBu
-2dBFS / +20dBu
-6dBFS / +16dBu
-12dBFS / +10dBu
-18dBFS / +4dBu
-42dBFS / -20dBu
Front and rear connectivity
Analogue Channel Inputs (Inputs 1-4)
• 4 instrument 1⁄4” TS jack inputs on front panel
• 4 microphone XLR inputs on rear panel
• 4 line 1⁄4” TRS jacks on rear panel
• 4 insert return 1⁄4” TRS jacks on rear panel
• 4 ADC XLR inputs on rear panel
Analogue Audio Outputs (Outputs 1-4)
• 4 line XLR outputs on rear panel
• 4 insert send 1⁄4” TRS jacks on rear panel
Other I/O
• IEC power input connector 100Vac – 240Vac
Front Panel Indicators
• 8 output meters, 6 segment
• 4 30-60 mic gain range selection indicator
• 4 +48V phantom power indicator
• 4 Phase indicator
• 4 Insert In indicator
• 4 Filter In indicator
• 4 Input selection indicators (Mic, Line, Inst)
• 4 Z In microphone input impedance selection indicators (Low, ISA110, Med, High) Clock select indicators (44.1, 48, 88.2, 96, 176.4, 192)
• Ext clock indicators (Lock, Word clock, 256X)
Weight
5.5kg
12.2lbs
Dimensions (W x H x D)
480mm (W) x 88mm (H) x 280mm (D)
19" (W) x 3.5" (H) x 11" (D)
| • Road proof housing
• High quality components
• Professional balanced XLR outputs
• Level control
The ASC-202 converts consumer level stereo RCA signals to balanced XLR professional line level, and back. One side of the unit, has two XLR inputs and stereo RCA outputs. The other side has stereo RCA inputs and two XLR outputs. Each side has stereo level controls. A possible application of the SC-13 is to use it as a level control in balanced audio lines.
The DAP Pro Audio Solutions are a complete line-up of audio tools for the professional musician or audio engineer. It is a series of audio modifying tools like mini-mixers, pre-amps and converters available in active or passive models. All audio solutions are designed to meet the highest stage and audio demands and feature a metal road proof housing with rubber feet and easy accessible controls. The units also have a small footprint which make them ideal to be used and placed in any environment where space is critical.
Specifications Frequency Response: 20Hz-20KHz
Inputs: XLR/Jack Combo, RCA
Outputs: XLR male, RCA
Input sensitivity RCA in: -10 dBv
Input Impedance RCA in: 10 kOhm
Input sensitivity XLR/Jack in: +4 dBu
Input Impedance XLR/Jack in: 20 kOhm
Output voltage RCA Out: -10 dBV
Output Impedance XLR Out: 100 Ohm
Output voltage XLR Out: +4 dBu
Output Impedance XLR Out: 200 Ohm
Power supply: 18V AC (adapter included)
Dimensions: 53 x 158 x 135 mm (HxWxD)
Weight: 0,65 Kg |
The CPR12 is an easy to use, flexible and multifunctional 10 channel pre-amplifier. Six of these input channels are selectable between Mic / Line level and equipped with a 3 band tone control. The first two can be switched to priority and phantom power. The other four channels are direct line inputs. Every input channel has its own gain and fader volume control with PFL button which makes it possible to pre-listen each input or output channel with the built-in pre-listening speaker, and can be routed to one or both output channels. This makes the CPR12 a full two-zone system. Other present features are a priority input, a recording output, separate sub-out channels and the 24 V DC emergency power connection. This last feature makes it possible to power the CPR12 with emergency power when the main power is shut down. In this case, the priority input will automatically mute all input signals, and a evacuation message will be announced. The steel 19" housing has a height of 2 HE. - 10 audio input sources
- 6 Mic / Line inputs with 3 band EQ
- 4 Direct Line Inputs
- Fader volume control
- Two output zones
- Built-in pre-listening speaker
- Priority input for emergency situations
- + 15 V DC Phantom power
- Works on 24 V DC emergency power
Specifications - Model Name / Type: CPR12 / 10 channel 2 zone pre-amplifier
- THD+N:
- Signal/Noise: > 90 dB
- Frequency Response: 20 Hz - 20 kHz
- Phantom Power: + 15 V DC
- Emergency Power: + 24 V DC
- Power Supply: 100 - 240 V AC / 50 - 60 Hz
- Dimensions (W x H x D): 420 x 88 x 320 mm
|
The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.
The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.
The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.
The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.
The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.
The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
- LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme. |
Reviews
There are no reviews yet.