FOCUSRITE ISA 428 FOUR CHANNELS MIC PREAMPLIFIER

Overview:

The ISA 428 Pre Pack is the perfect multi-channel front end for any professional DAW.
Four classic Focusrite transformer-based pre amps with switchable impedance and direct
instrument inputs. An optional eight channel 192kHz ADC, preceded by the all new proprietory
Soft Limiter circuit, provides the perfect path into your Pro Tools HD system.
The benefits of the pre amp's topology include superb common-mode rejection, an excellent
overload margin and, with its shared gain structure (20dB from the hand-wound transformer and
up to 40dB from the amplifier), an extremely low noise floor and super-wide bandwidth (10Hz to
200kHz). This pre amp design is the cornerstone of Focusrite's signature 'warm-yet-transparent'
sound and is a point of reference for any discerning audio professional.
In addition, the input stage provides enhanced control and creativity allowing you to switch between
four carefully selected input impedance settings. The original ISA 110 setting is supplemented by
three further impedance settings to either perfectly match the pre amp with any microphone and
maximise level, or use different settings creatively to shape the sound of the microphone being used.
Should the need arise to place extra processing in between pre amp and conversion, insert points are
also featured on every channel.
Protecting the ADC, the Soft Limiter opto circuit is a new design from Focusrite, entirely preventing any
'digital overs', whilst minimising the undesirable distortion that standard limiter circuits often generate.
Finally, the new ADC embodies cutting-edge conversion technology, encompassed within pristine Focusrite
circuitry, providing eight conversion channels of the highest quality, at frequency rates of up to 192kHz.
Running at 96kHz allows for up to 16 (2 x 8, parallel) simultaneous digital outputs in addition to the four
main analogue outputs. Digital output options include dual AES/EBU, SPDIF and dual ADAT lightpipe.
Full digital metering is provided for every channel, alongside new 'moving coil' peak meters, designed to
catch even the fastest of transients.
A second analogue unit can be connected utilising the four extra ADC input channels on the rear of the unit
containing the optional ADC. This makes full use of the eight channels provided on a single optional ADC and
expands your front-end capacity from four pre amps and eight digital outputs to eight Pre amps and eight digital
outputs.
Classic preamp technology, custom Focusrite input and limiting circuits and the very best in A/D conversion
technology, the ISA 428 Pre Pack raises the bar for multi-channel recording solutions into Pro Tools HD, or any
other professional DAW. Equally, it can be used as an additional set of high quality pre amps for any analogue
or digital console or hard disk recorder.
Four classic Focusrite transformer-based preamps.
8 channels of cutting-edge A/D conversion, running at up to 192kHz. Protected by proprietory optical Soft Limiter
circuit.
Switchable Impedance for unparalleled mic matching or extended mic creativity - includes the classic ISA 110
setting.
Multiple Front Panel Instrument DI. No separate DI box required.
Analogue insert points on every channel.
High Pass Filters on every channel.
New moving coil peak meters & full digital metering (dBfs).

ADAT is a trademark of Alesis Corp
Pro Tools HD is a trademark of Avid Technologies plc.
The 192kHz ADC is an extra cost option.

Specifications
Inputs
Transformer-based ISA design
Gain range: Line = +/- 18dB, Mic = 0 to 60dB (both in 6dB steps), Inst = +10 to +40 dB
variable
Input impedance: Line = 10k ohm, Mic = Variable - 600, 2k4 and 6k8 ohm + original ISA 110
settings, Inst = >1M ohm

Analogue Performance
Noise: Line = -96dB, Mic = -128dB (EIN with 150 ohm input resistance at 60dB of gain)
THD: Line = 0.003% with 0dBu, 1kHz input and 20Hz to 22kHz band-pass filter, Mic = 0.003%

Analogue Input and Output connectors (balanced)
D.I inputs: 1/4 inch Jack (unbalanced)
Mic inputs: XLR (balanced)
Line: TRS Jack (balanced)
Insert Sends and Returns: TRS Jack (balanced)
Additional ADC inputs: XLR (balanced) Line level
Analogue Outputs: XLR (balanced)

Digital Output Option
AES/EBU and S/PDIF dual 9-pin D-types
Optical - ADAT Lightpipe
Bit depths 16-, 20- or 24-bit
Frequency options 44.1, 48, 88.2, 96, 176.4 and 192kHz
Clock options Standard or ?256 x?
Meter - 0 dBFS = +22dBu
Digital Performance
SNR - 120dB A-weighted

The PRE-73 MKIII is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The in- and output is transformer balanced, using two different transformers, each one optimized for its purpose. This is the way audio components were built before integrated circuits became available.

The circuit used in the PRE-73 MKIII is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

Features  :

• Vintage Style electronics. No intergrated circuits in the signal path.

• Maximum gain in MIC mode is 80 dB, enough to handle passive ribbon mics with quiet sound sources.

• GAIN switch range 20 - 80 dB. GAIN/LINE mode switch, gain is reduced by 30 dB in LINE mode.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable 6 dB/octave two frequency high pass filter at around 40 (HP1) and 170 Hz (HP2).

• Tantalum capacitors in the signal path.

• Switchable impedance in MIC mode, 1200 or 300 Ohms, will change the tone of most mics. The input impedance in LINE mode is 10 kohm.

• Switchable phantom power and absolute phase.

• A high-impedance instrument input for any sound module, electric guitar or bass.

• A simple but effective 4-step LED output level meter.

• The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.

• Combo XLR/TRS input jack and separate output XLR and TRS jacks for flexible connections.

• Insert jack for inserting EQ´s and other units.

• Selectable 600 ohm output termination.

• The pcb is prepared for the Carnhill input transformer.

• External power supply to avoid interaction with the audio circuits and transformers.

• A solid build quality that will last many years of normal use.

The MKIII has the following new features compared to the MKII:

• Tantalum capacitors in the signal path.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable two frequency high pass filter, 6 dB/octave at 40 or 170Hz.

• The pcb is prepared for the Carnhill input transformer.

• Revised and less complicated GAIN switch with a separate switch for MIC/LINE selection.

• All GAIN settings can also be used in LINE mode .

The PreSonus HP60 is the most flexible and advanced headphone amplifier system available for professional and project recording studios as well as live sound in-ear monitoring systems. Loaded with six independent,
loud and clear headphone amplifiers, the HP60 features dual stereo inputs as well as external input, for each
channel allowing you to mix between three stereo audio streams (mix A, mix B, and external input). Stereo output is also available on each channel to send line level headphone channel mixes to additional headphone amplifiers or monitor systems. Each channel features headphone level, mix control between A and B inputs, external input volume, mute and mono. The HP60 also features talkback via external XLR microphone input. Common set up of the HP60 in a recording session is to send the main control room mix to input A. Send the click track to input B. Send the each band member direct recording input to each channelʼs external input (more me). This will allow each band member to create a mix between the main mix, the click track and themselves. The HP60 is the ultimate headphone amplification system delivering loud and clear headphone mixes for real-world recording situations.

Features:
-Six independent ultra low noise, high output headphone amplifiers (150 mW per channel)
-Two sets of stereo inputs (A and B) with balanced TRS connectors
-Stereo external input point on each channel for "more me” with trim control
-Mix control between inputs A and B
-Talkback with external XLR microphone with control
-Direct stereo line output on each channel

• Maximum of 66 dB of gain, in eleven discrete steps
• Dynamic range exceeding 120 dB
• 10 Hz to 50 kHz audio bandwidth
• High immunity to RF interference
• High current line output driver
• Transformer-balanced input and output
• Extended range peak limiter via dual opto-isolators makes preamplifier virtually "unclippable“
• Selectable 48-volt / 12-volt phantom power or 12-volt "T" power
• High-pass filter @ 80 or 160 Hz, 6 dB per octave
• Headphone monitoring of microphone audio, monitor audio, or a mix of both
• Monitor input accepts mono, balanced or unbalanced line-level inputs on 1/4-inch tip-ring-sleeve connector
• Separate level control of Monitor gain and overall headphone gain
• Split ear function via DIP switches
• Internal battery power (two-AA)
• Excellent battery life with alkaline and NiMH rechargeable batteries
• External 5-17 VDC powering (plug included)
• High-strength aluminum chassis with durable belt clip

Having had great success with the PRE-73 preamp, we have received many requests for a version for the 500 eries rack format. We are therefore happy to present the PRE-573, expected to start shipping in late September.
 
The PRE-573 is a one width module that has the sound and the features that made the PRE-73 so successful and a few additional ones.
The circuit still uses the preamp and output section from the classic 1073-module, adapted to work in the api rack format. It has a total  gain range from -15 to +80 dB. The 10 - 70 dB range is handled by a turn switch  and there is a separate toggle switch to select an additional 5 or 10 dB gain. The input can be configured to accept line level signals by another switch, the gain is then lowered by about 25 dB and the input impedance increased to about 15 kohm.
 
The input impedance of the mic input mode can be switched between 1200 and 300 ohm. Phantom power and phase reverse is also selectable by front panel switches.
 
An added feature, using the same circuit as in the PRE-73 DLX, is the active DI-input with a high input impedance of about 1,5 Mohm. The output signal from the active DI circuit passes through the input transformer for some extra character.
The DI-input is very flexible since it can be changed to a purely passive one by a front panel switch. The DI input is then exactly the same as in the PRE-73 Mk2 where the signal is feed directly into the second gain stage, bypassing the transformer and with an input impedance of about 100 kohm.

These two DI-options makes it possible to get different tones from electric instruments and the passive DI input mode is more suited for injecting active units like sound modules. 
 
A new feature is the switchable AIR mode that  adds a small boost above 10 kHz that peaks at 2 dB at about 35 kHz.

A simple but effective signal and overload indicator is offered by a single LED that starts glowing red at about +4 dBu and then increases its intensity up to the maximum output level.
 
The PRE-573 has a dedicated insert connector at the back allowing it to interface with other GAP 500 modules. The insert can be activated by removing a jumper connector at the back of the module.
The second Golden Age Project module for the api 500 rack will be the EQ-573, expected to ship in November 2012. The EQ-573 consists of the inductor based high pass filter section  and the 3-band eq section from the classic 1073 module with some added frequencies. These two modules together will offer a fully fledged 1073-module in a compact format at a very low cost.
 
There is a second jumper at the back of the module that selects 600 ohm termination on the output. The standard mode is termination on, since it gives the flattest response when the PRE-573 is used with modern line inputs that typically has an input impedance of 10 kohm or more. The user can chose to remove the jumper and deactivate the termination resistor, this will increase the level above 10 kHz and create a peak in the response for an even more pronounced  "Air" effect.
The output is transformer balanced and fully floating and can drive a 600 ohm load up to level of about 28 dBu.