| Content |
The new PH-100 is a remarkably quiet, 1U rackmount headphone distribution amplifier.
Each output has its own amplifier as well as its own level control - so different individual
listening requirements can be met with ease. Multiple PH-100s can also be cascaded
to handle a large number of listeners making it ideal for orchestral, multimedia, education
and trade show applications. The PH-100 is especially handy in the studio environment
because an output from the mixer can send a talkback signal to the Aux input (complete
with level control) of the PH-100 and be distributed to all headphone outputs. This great
cue system makes for more effective communication between engineer/producer and
musicians.
Flexibility is further enhanced with all ten outputs being available both on the front and r
ear panels.
* Ideal for studio, orchestral, education, multimedia, conference and exhibition applications
* 10 headphone outs - each with its own amplifier
* Each input routes to its direct output, plus Aux 1 source (cue feed)
* Multiple inputs: XLR, phone, RCA pin jacks
* +4dBu or -10dBV switchable for balanced inputs
* Individual level controls with peak reading LED
* Stereo or mono input select
* Cascade inputs & outputs for ?daisy chaining? units
* Aux In with level control for cue feed from main mixer
SPECIFICATIONS:
INPUT
INPUT L, R (balanced)
Connector XLR-3-31 x 2, phone x 2
Input Level +4dBU (XLR-3-31), -10dBV (phone)
Input Impedance more than 10k ohm
INPUT L/MONO, R (unbalanced)
Connector RCA pin x 2
Input Level -10dBV
Input Impedance more than 10k ohm
AUX In L/MONO, R (unbalanced)
Connector RCA pin x 2
Input Level -10dBV
Input Impedance more than 10k ohm
CHANNEL IN 1-10 (unbalanced)
Connector RCA pin x 2
Input Level -10dBV
Input Impedance more than 10k ohm
OUTPUT
PHONES OUT 1-10
Connector Phone x 20
(10 each on front/rear, priority on front outputs)
Maximum Output Level 500mW
Impedance 8 ? 32 ohm
Frequency Response 30Hz ? 20kHz +/-1dB
Residual Noise less than -65dBV
THD less than 0.3%
CASCADE OUT L,R
Connector RCA pin x 2
Output Level -10dBV
Frequency Response 30Hz ? 20kHz +/-1dB
S/N less than -80dBV
THD less than 0.1%
PHYSICAL
Dimensions 484 (W) x 49 (H) x 267 (D)
Weight approx. 4kgs.
Power 120V / 230V
Power Consumption 18W | LDHPA6 6-Channel Rackmount Headphone Amplifier
The LD Systems HPA 6 is a highly flexible 1U 19" rack format headphone amplifier with 6 fully independent channels and comprehensive features for a wide range of professional audio monitoring applications.
Each channel provides a 6.3 mm TRS headphone output on the front panel with level control, mono/stereo switching, discrete left/right muting and a 6.3 mm TRS Aux input with Main/Aux balance control for mixing in further signal sources. Four-segment LED meters permit visual output level monitoring, and two 6.3 mm TRS outputs per channel on the rear allow for connecting a total of 18 headphones.
The HPA 6\'s main section features a master level control with eight-segment LED metering and 6.3 mm TRS input to mix in an additional source with all channels. The rear panel provides the main stereo inputs on balanced XLR and 6.3 mm TRS connectors and stereo outputs for daisy chaining multiple units.
- Type: 6-channel
- Inputs: Main Input (Stereo), Direct In (Stereo), 6 x Aux In (Stereo)
- Input Connections: XLR and 6.3 mm jack L&R (Main Input, balanced), 6.3 mm stereo jack (Direct In), 6.3 mm stereo jack (Aux In)
- Input Impedance: 13 kOhm
- Line Outputs: Main Output (stereo, balanced)
- Line Output Connectors: XLR and 6.3 mm jack L&R
- Headphone Outputs: 6 x 3
- Headphone Output Connectors: 6.3 mm stereo jack
- Power Output: 6 x 125 mW
- Minimal Connected Impedance per Channel: 8 ohms
- Frequency Response: 20 Hz - 20.000 Hz
- Controls: Main Input Level, 6 x Input Mix Main/Aux, 6 x Headphone Level, 6 x Mono Switch, 6 x Mute L&R, Power
- Indicators: Main Input/Direct In Level Meter (8-segment LED chain), 6 x channel level meter (4-segment LED chain), 6 x mono LED, 6 x Mute L&R LEDs, Power LED
- Power Supply: IEC power socket
- Operating Voltage: 220 - 240 V AC, 50 - 60 Hz / 110 - 120 V AC, 50 - 60 Hz
- Power Consumption: 40 W
- Cabinet Material: metal
- Cabinet Surface: painted
- Width: 483 mm
- Height: 44 mm
- Depth: 217 mm
- Accessories (included): power cord
| Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
|
- Ultra-compact monitor headphone amplifier for studio and stage applications
- Personal \'\'more me\'\' mixer – mix a mic plus a monitor signal and hear them via headphones
- Flexible Mic In and Mic Through connectors plus Ground Lift switch
- Stereo Monitor input with dedicated Monitor Level control and Mono/Stereo switch
- High-power headphone output on 1/4\'\' and 1/8\'\' jack connectors
- DC 12 Vadapter included
- 3-Year Warranty Program*
- Designed and engineered in Germany
|
The amPlug Night Train perfectly simulates the high-gain sound of the compact VOX Night Train tube amp. Just as with the actual Night Train head, you can switch between the two preamp sounds. The BRIGHT position boosts the high-frequency range; the THICK position offers a chunkier, heavier sound. The emulated speaker cabinet circuit accurately recreates the sound of the Night Train amp being played through the matching V112NT single 12" Night Train speaker cabinet. As a finishing touch, amPlug Night Train share some of the cool looks of its namesake amplifier.
Specifications - Controls: Gain, Tone, Volume; STANDBY/ON/FX switch
- Terminals: PHONES Jack (stereo), AUX In Jack (stereo)
- Power supply: AAA batteries (x 2)
- Battery life: amPlug Night Train:
- With zinc-carbon batteries: approximately 9 hours
- With alkaline batteries: approximately 24 hours
- Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22“
- Weight: 40 g/1.41 oz. (not including batteries)
- Included items: AAA batteries (X2) (for verifying operation)
|
Overview
With Sennheiserʼs HDVD 800, sound is perfect. The HDVD 800 is able to connect with digital sources and is equipped with a high-quality Burr-Brown digital/analog converter (DAC) that converts digital audio data into analog signals with a resolution of 24 bits and a sampling rate of up to 192 kHz. This enables the HDVD 800 to transmit the entire frequency spectrum of high-end audio sources without any loss of frequencies.
In addition to the symmetrical inputs, the HDVD 800 also has an asymmetrical input socket; incoming signals are symmetrized before further processing takes place. Digital sources can be connected to the rear of the unit via an XLR (AES/EBU) input, optical and coaxial (S/PDIF) digital inputs or USB. All digital inputs accept signals up to 24 bit at 192 KHz*. Designed and manufactured in Germany, this high-end, solid-state amplifier harmonize perfectly and deliver an ultimate acoustic performance when paired with any of Sennheiserʼs audiophile headphones.
Features
D/A transducer for all common formats up to 24 bit / 192 kHz
D/A transducer can be used for CD and DVD players
AES/BU, S/PDIF, USB inputs
Symmetrical (XLR) and asymmetrical (RCA) analog inputs
Symmetrical output
Sockets for four sets of headphones (two of which symmetrical)
|
Reviews
There are no reviews yet.