| Content |
| | - DIGITAL PROCESSING & DIGITAL AMPLIFIER Designed with full digital amplifier, low power consumption, low set weight and low heat. - BUILT IN SOUND SOURCE You can use the FM digital tuner and MP3CD player which are built in the system for your convenience. - SPEAKER SELECTOR (5 ZONE) Six speaker select switches enable you to select any combination of up to five speakers. - RS-232C IN/OUT CONTROL AMX/CRESTRON Interface can be used with the RS-232C terminal - DIGITAL 3 BAND EQ Digital 3 band EQ for 6 Mic inputs. - PRIORITY MUTING Selectable audio signal priority for MIC Channel 1 and 2. Priority : EM > TEL-IN > RM > MIC1/2 - ANNOUNCEMENT CHIME Convenient two-tone and four-tone chime for announcement. - EM (EMERGENCY) When the EM terminals are connected in emergencies, EM broadcasting stored in VOICE IC is outputted. - REMOTE CONTROL The unit can be used with the remote amplifier, RM-05A. - IR REMOCON (OPTION) The unit can be controlled by the remocon. Power on/off, volume up/down, CD, FM, etc can be controlled by the remocon. ACCESSORIES - One detachable AC power cord is provided for use with this product. - FM Antenna | | | | | | * 0dBV=1V | | | PCT-610 | PCT-620 | | AUX INPUT(AUX IN @1kHz, 4Ω Load Output) | | Rated Output Power | 120W | 240W | | Input Sensitivity | -10dBV/10kΩ | | S/N, AES-17 WTD | ≤ -80dB | | Tone Control(BASS:100Hz, TREBLE:10kHz) | ±10dB | | Frequency Response (1W Power Output, ±3dB) | 90Hz-18kHz | | T.H.D. | | | MIC 1 ~ 6 Input (MIC IN @1kHz, PRE OUT) | | Input Sensitivity | -60dBV ~ -16dBV/10kΩ | | S/N, A-WTD | ≤ -60dB | | Frequency Response (±3dB) | 120Hz-10kHz | | Phantom Power | +24V DC | | Remote IN (Remote IN @1kHz, PRE OUT) | | Input Sensitivity | -60dBV/10kΩ | | S/N, A-WTD | ≤ -50dB | | Frequency Response (±3dB) | 120Hz-10kHz | | TEL IN (TEL IN @1kHz, PRE OUT) | | Input Sensitivity | -2.2dBV/10kΩ | | S/N, A-WTD | ≤ -65dB | | Frequency Response (±3dB) | 330Hz-3kHz | | CD (Test CD 0dB, 1kHz @ PRE OUT) | | S/N, A-WTD | | | Frequency Response (±3dB) | 80Hz-18kHz | | TUNER (FM, 22.5kHz, MOD @ PRE OUT) | | S/N, A-WTD | | | Frequency Response (±3dB) | 100Hz-14kHz | | PRE OUT (MIC1~6, AUX IN TEL IN, Remote IN) | | Output Level | 0dBV/600Ω | | T.H.D | | | POST OUT /Output Level | 0dBV/600Ω | | Operating Temperature | -10°C ~ +40°C | | Power Source | 120VAC or 220-240VAC; 50/60Hz, 24VDC** (Different voltage setting on SMPS depends on country) | | Power Consumption(1/8 power) | 90W | | Weight | 10kg/22.7lb | 11kg/24.3lb | | Dimensions | 420(W) x 132(H) x 380(D)mm/16.5(W) x 5.2(H) x 15(D)in | | ※ Specifications and design subject to change without notice. ※ In case of changing the voltage setting of 120Vac or 220~240Vac on SMPS, MUST refer it to qualified service personnel. | | | |
|
Crown CDi 1000 2x700W-4Ω Power Amplifier
The Crown? CDi 1000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply.
The outputs shall be usable as dual or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker. Dual connectors shall work with 2-8 ohm or
70V loads. Bridge-mono connectors shall work with 4-8 ohm or 140V loads.
HiQnet USB Connector: Type B, connects to a USB port on a PC.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Dual (per channel): 700W with 1% THD, 4 ohm Dual (per
channel): 500W, 8 ohm Dual (per channel) 275W, 4 ohm Bridge-Mono: 1,400W
with 1% THD, 8 ohm Bridge-Mono: 1,000W, 70V Dual (per channel): 500W.
Voltage Gain at 1kHz, 8 ohm rated output: 30.5 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity: 1.4V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.5A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave and Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB
bandpass gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 20 presets. 19 are user-definable.
Protection shall include the following:
CDi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg).
The amplifier shall be designated the Crown CDi 1000. |
Crown CDi 2000 2x800W-4Ω Power Amplifier
The Crown? CDi 2000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply.
The outputs shall be usable as dual or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker. Dual connectors shall work with 2-8 ohm or
70V loads. Bridge-mono connectors shall work with 4-8 ohm or 140V loads.
HiQnet USB Connector: Type B, connects to a USB port on a PC.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Dual (per channel): 1,000W with 1% THD, 4 ohm Dual
(per channel): 800W, 8 ohm Dual (per channel) 475W, 4 ohm Bridge-Mono:
2,000W with 1% THD, 8 ohm Bridge-Mono: 1,600W, 70V Dual (per channel):
800W.
Voltage Gain at 1kHz, 8 ohm rated output: 32.9 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Dual
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity: 1.4V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB (A
weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.9A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave and Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB
bandpass gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 20 presets. 19 are user-defi nable.
Protection shall include the following:
CDi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg).
The amplifier shall be designated the Crown CDi 2000.
|
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
| Specification | |
|---|
| Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
| Output |
120W |
| Power Consumption |
AC operation: 158W (rated output), 66W (EN60065)
24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
| Frequency Response |
50 - 20,000Hz ±3dB |
| Distortion |
Under 2% at 1kHz, rated power |
| Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins)
MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack
AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack
AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack
AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack
TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
| Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack
LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack
MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal
SPEAKER SELECTOR:
2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/83Ω),M4 screw terminal
Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
| Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio
(Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min)
Over 76dB (Master volume: max)
Over 60dB (MIC 1 - 3))
Over 76dB (AUX 1 - 3)
Over 90dB (TEL)
Over 96dB (EMERGENCY) |
| Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal
EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
| Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
| Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
| Priority |
EMERGENCY: Overrides other inputs
TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting
MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
| Operating Temperature |
-10ºC - +40ºC |
| Finish |
Panel: ABS resin, black, hair line
Case: Steel plate, black |
| Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
| Weight |
12.6kg |
| Accessory |
Power cord x 1,
Terminal block cover x 1,
Terminal block cover mounting screw x 2 |
| Option |
Rack mounting bracket: MB-25B,
Volume control cover: YA-920,
Input transformer: IT-453A |
| Note* |
(*1) 0dB = 1V
(*2) Can be transformer-balanced with the addition of optional IT-453A input transformer.
(*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.)
(*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with the VP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.
| Power Source | Supplied from VP-2064, VP-2122, VP-2241 or VP-2421 | | Current Consumption | 30 mA or less | | Power Amplifier Link | RJ45 female connector for connecting the VX-200SP,
VX-200SZ Audio Output module, or SX-2100AO.
Twisted-pair straight cable (TIA/EIA-568A standard) | | Finish | Panel: Surface-treated steel plate | | Dimensions | 88 (W) × 25.8 (H) × 53.2 (D) mm | | Weight | 50 g | | Applicable Model | VP-2064, VP-2122, VP-2241, VP-2421 |
|
| | - SPEAKER SELECT(5ZONE SPEAKER OUTPUT) Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for MIC Channels 1, siren, Chime and Telephone input over other input sources. - MONITOR SPEAKER You can monitor output signal by using the monitor speaker, and can control the monitor level on front panel by 3 step lever switch. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - REMOTE CONTROL INPUT Individual speaker zones can be selected and chime can be operated by wired remote control. - EM(EMERGENCY) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. - REMOTE POWER You can turn on/off amplifier by remote control. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-510/520ʼs audio capabilities. ACCESSORIES One detachable AC power cord is provided for use with this product. | | | | | | | PAM-510 | PAM-520 | | Amplifier Section (Amp In@1kHz, 4Ω Load Output) | Rated Output Power (THD 1%) | 120W(RMS) | 240W(RMS) | | Speaker Zone 1~5 Output | 25W MAX | 50W MAX | | Input Sensitivity/Impedance | 1V/20kΩ | | S/N | Better than 85dB | | Frequency Response (at 1kHz Half Power Output, ±3dB) | 80Hz~18kHz | | Mic Input Section (Mic 1~4 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –60dBV/600Ω | | S/N | Better than 55dB | | Frequency Response (±3dB) | 120Hz~10kHz | | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | | Phantom Power | +24VDC | | Line Input Section (Line 1~2 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –30dBV/10kΩ | | S/N | Better than 65dB | | Frequency Response (±3dB) | 80Hz~15kHz | | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | | Remote Amp Section (Remote In@1kHz, Preamp Out) | Mic Input Sensitivity/Impedance | –60dBV/600Ω | | S/N | Better than 55dB | | Frequency Response (±3dB) | 120Hz~10kHz | | Tel In Section (Tel In@1kHz, Preamp Out) | Input Sensitivity/Impedance | 0.3V/600Ω(USA/Canada) | | 0.775V/600Ω(EC & Associated) | | S/N | Better than 65dB | | Frequency Response (±3dB) | 330Hz~3kHz | | Pre Amp Out(Mic 1~4, Line 1~2, Tel In, Remote In) | 0dBV/600Ω | | | T.H.D | Less than 0.5% | | Record Out | –10dBV/3kΩ | | Operating Temperature | –10°C~40°C | | Power Source | 100–120VAC or 220–240VAC; 50/60Hz, 24VDC | | Power Consumption (1/8 POWER) | 180W | 320W | | Weight | 17kg/37.6lb | 19kg/42lb | | Dimensions | 482(W) x 132(H) x 398(D)mm 19(W) x 5.2(H) x 15.7(D)in | | ※ Specifications and design subject to change without notice. | | | |
|
Reviews
There are no reviews yet.