| Content | L1400 450W-450W 4ohm (280W-280W8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
| AMPLIFIER SPECIFICATIONS |
|---|
| Power output stereo 4Ω: | 2 x 300 Watt rms | | | Power output stereo 8Ω: | 2 x 180 Watt rms | | | Power output bridged 8Ω: | 600 Watt rms | | | Frequency Response: | 20 Hz ÷ 20 kHz | | | Signal/noise rate: | > 105 dB | | | Crosstalk: | > 70 dB | | | Distortion (THD+N): | | | | Intermodulation: | | | | Damping factor: | 200:1 (8 Ω) | | | Slew rate: | 50 V/μS | |
| INPUT SECTION |
|---|
| Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | | Input impedance: | 10.000 kΩ | | | Controls: | Volume control for each channel | |
| OUTPUT SECTION |
|---|
| Output connector: | 2 x Neutrik Speakon 4 ways | |
| SYSTEM PARAMETERS |
|---|
| Cooling: | Two-speed fan | | | Protections: | Temperature, DC, RFI short circuit, Soft-Start thermal on transformer | | | Amplifier class: | H | |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | | Max.current: | 6 A | | | Power Consumption: | 1300 W | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 88 / 3.46 mm/inch | | | Width: | 483 / 19.01 mm/inch | | | Depth: | 350 / 13.77 mm/inch | | | Net Weight: | 11.45 / 25.24 Kg/Lbs | |
| SHIPPING INFORMATION |
|---|
| Package height: | 120 / 4.72 mm/inch | | | Package width: | 540 / 21.25 mm/inch | | | Package depth: | 470 / 18.05 mm/inch | | | Shipping Weight: | 13.81 / 30.44 Kg/Lbs |
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange, and superbly defined highs. They also deliver fast response and exceptional stability even in the face of serious power supply limitations. Refinements throughout this expanded five-model lineup make these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 250 Watt / 8Ω RMS, 2 x 450 Watt / 4Ω RMS, 900 Watt / 8Ω bridge RMS. Weight: 12,5 Kg.
|
VLP Series Power Amplifier
Output Power:
- 150W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
- 100W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
(Bridge Mode, Mono)
- 300W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 260
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift
Dimensions (LxWxH): 13.25" x 19" x 1.75" / 336 x 482 x 44mm (1-rack mount space)
Weight: 24 lbs. / 11Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift
|
XB Series - Intelligent Power
Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XB 400: 2x 200 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.025%
Signal-to-Noise Ratio: < 103 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: 500 @ 4 Ohm
Cooling: 2x fan (temp. reg. variable speed)
Weight:12 kg /(26 lbs)
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
The model L 500 is a 2 x 250 Watts Power Amplifier. Linear Precision Series
power amps combine excellent audio performance, modern and innovative
circuit design, meticulous and exceptionally rigid construction, and the highest
levels of operational integrity and reliability with an appropriate and more than
realistic price. The robust steel chassis provides outstanding torsional strength
through L-shaped side panels reaching under the thick aluminium front panel.
Thermal breakers prevent the power supply units from being damaged by thermal
overload. Electronically controlled fans provide sufficient front-to-rear airflow and
a special cool air diverter takes care of thermal stability. The fans? noise-level is
extremely low which provides the possibility for studio use. If necessary, a supplied
air-filter can be mounted behind the front panel ventilation louvres.
Features
* Excellent audio performance
* Symmetrical topology
* Ultra-low distortion
* Generously dimensioned power supply units
* Suitable to be operated on loads down to 2 ohms
* Suitable to drive complex loads with phase angles of ± 90 degree
* Extensive protection circuitry
* Unique Back-EMF protection
* Switchable limiters
* Switchable Hi/Lo-Cut filters
* Robust steel chassis
* Exceptional low noise front-to-rear air-flow
* XLR-type inputs and direct-outs
* LED display shows On, In, Out, Limit and Protect
* Highly reliable operation
Specs
* Max. Output Power - into 8 ohms : 2 x 180 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 4 ohms : 2 x 280 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 2 ohms : 2 x 320 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 8 ohms bridged : 1 x 560 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 4 ohms bridged : 1 x 640 W at 1 kHz / THD = 1.0%
* Rated Output Power - into 8 ohms : 2 x 175 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 4 ohms : 2 x 250 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 2 ohms : 2 x 300 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 8 ohms bridged : 1 x 500 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 4 ohms bridged : 1 x 600 W at 20 Hz - 20 kHz / THD = 0.1 %
* Frequency Response : 0 dB ..... -1 dB/20 Hz - 20 kHz
* Phase Angle Response : ± 30 degree/20 Hz.....20 kHz
* Maximum Output Level : 45 V / RMS before clipping, no load, ref. 1 kHz / THD = 1%
* Voltage Gain ref. 1 kHz : 26 dB (constant gain option)
* Input Sensitivity : 0 dBu/0.775 V, +6 dBu/1.55 V at rated output / 4 ohms ref. 1 kHz
* Maximum Input Level : +21 dBu / 8.7 V
* Input Impedance active balanced : 20 kohms
* THD at Rated Output : < 0.05 % MBW = 80.0 kHz, f = 1 kHz
* IMD -SMPTE : < 0.01 % 60 Hz, 7 kHz, at rated output
* Signal-to-Noise Ratio : >105 dB at rated output into 4 ohms,
A-weighted, RMS, input sensitivity +6 dBu
* Attenuation at rated output : > 70 dB f = 1 kHz
* Damping Factor internal 1 kHz : > 300
* DIM 30 : < 0.01 %
* DIM 100 : < 0.01 %
* Slew Rate internal : > 25 V / ?s
* Power Consumption : 300 W 1/8 rated output into 4 ohms
* Width : 483 mm
* Height : 88.1 mm
* Depth : 426 mm
* Weight : 14 kg
|
Reviews
There are no reviews yet.