| Content |
Power Output Level QX4960:
8ohm 1kHz (Quad CH) 170W x 4
4ohm 1kHz (Quad CH) 240W x 4
8ohm 1kHz (bridged mono) 480W x 2
(1kHz, 1% THD)
Input Sensitivity 0.775Vrms
Input Impedance 20kohm Balanced
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz) Less than 0.1%
Signal to Noise Ratio 100dB
Protection Over heat and over current, output short, DC fault
X-Over Frequency 60Hz~2.5kHz
X-Over Cut Off Slope 24dB/Oct
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 770W
Net Weight 17kg/37.5lb
Dimensions 482(W) x 88(H) x369(D) mm
/19(W) x 3.5(H) x14.5(D) mm
Quad Amplifier - 4 Amp Circuit in the One Unit
Substantial Protection Circuitry
Various Display - Power, Protection, Clip and Signal
Mode Switch - Parallel, Stereo and Bridged Mono
Variable Speed Fan Cooling
Input Connectors - Balanced Combination Jack
Output Connectors - 5-Way Binding Post
Built In 2 Way Crossover
| • Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
| |
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
| RMS, 1kHz, 1.0% THD+N |
|
|
|
|
| 4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
| 8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
| Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
| Pink Noise 12dB CF |
|
|
|
|
| 4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ | PA Power Amplifier 4 x 160 W 4 Ohms
Multichannel Power with Minimum FootprintThe T Series multichannel power amplifiers have been designed especially for installation and networked audio systems.
T Series amplifiers* are available with 4 and 8 discrete channels and output ratings from 160 to 320 Watts per channel providing optimum solutions for multizoning. They feature Euroblock inputs, terminal strip outputs and a rugged 2U rackmountable chassis with 4 mm front panel.
*Also available as GPIO versions with remote and emergency paging switchin
Main Features
- 8 and 4-channel models with 300 and 150 Watts (RMS) output power per channel
- compact 2U rackmountable chassis, 220 mm deep, weight 6 kg only
- GPIO versions for remote and emergency paging switching
- FCM system
- oversized heat dissipation system for maximum thermal stability
- low THD and high S/N ratio
- all channels bridgeable in pairs
- switchable input gain (26, 32 and 38 dB)
- subsonic filters for each channel (35 Hz)
- intelligent, quiet fan cooling system
- terminal strip loudspeaker connectors
- PCBs with surface-mount technology (SMT) for increased reliability
- balanced inputs with superior noise rejection
- select high-quality components only
- ICL intelligent clip limiters for each channel
- recessed volume controls (optional SC-T perspex guard)
- high-efficiency two-stage Class H design
- protection, signal, clip, power on and standby LED indicators for each channel
- compact QuantaPulse power supply
- multi-voltage: automatic voltage converter for worldwide use, no switching required
- protections: soft start, turn on/turn off muting, thermal overload, DC, RF, short circuit, open circuit, load mismatch and power supply overload
ICL™: improved Intelligent Clip Limiting prevents loudspeaker damage while maintaining audio quality and punch under clipping conditions.
FCM™: the Faulty Channel Management system prevents overall amplifier shutdown.
GPIO:General-Purpose-I/O-Port
QuantaPulse™ Technology: The Soft Switching Resonant QuantaPulse Power Supply is designed to provide plenty of power when needed monitoring the necessary parameters of voltage and current for a controlled performance at all times. Bi-directional data flow between the power supply and power amp module. Two very important characteristics of the QuantaPulse power supply are the optimization against over-voltages and superior reliability.
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less power devices attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
Power Output Level: QD4240
8ohm (Quad Ch) 40W
4ohm (Quad Ch) 60W
8ohm bridged mono 120W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
|
The DPA series amplifiers are digital power amplifiers designed to meet the specialized needs of sound contractors for Multi-Zone distributed speaker systems. They are designed in six different models of Class D power amplifiers, divided in three different architectures to meet the requirements for all kinds of applications.
They combine the best of all features in one single series of amplifiers, providing an outstanding sound quality with all the known advantages of Class D Amplifiers. Such as the excellent efficiency and very low heat dissipation. And due to the complete passively cooled entity only a minimal of maintenance is needed, while ensuring maximum reliability.
The small size of a single rack space make them very interesting for fixed rack mount as well as mobile applications.
The DPA74 is built as multi channel power amplifier with four individual controllable channels containing various specific features and advanced protection circuitry which protects against DC malfunctioning, short circuit, overheating and overload.
The signal input connections are accommodated with balanced XLR connectors. The operation mode can be selected between Stereo mode, Bridge mode and Parallel mode. The output connections are accommodated with Euro-Terminal blocks.
- Model Name / Type: DPA74 / Digital Amplifier
- 8 ohms: 4 x 50 W
- 4 ohms: 4 x 75 W
- 8 ohms Bridge: 2 x 150 W
- THD+N:
- Signal / Noise: > 100 dB
- Frequency Response: 20 Hz - 20kHz
- Power Supply: 240 V AC / 50 - 60 Hz
- Dimensions (W x H x D): 483 x 44 x 300 mm
| - 6CH 60W DIGITAL AMPLIFIER
- LIGHT WEIGHT
- 6 BUS BROADCASTING FUNCTION WITH A UTP (CATEGORY 5) CABLE.
- VOLUME AND 5 BAND EQ TUNING FUNCTION BY CHANNEL
- AMP ID AUTO/MANUAL ALLOCATION FUNCTION
- SELF-BROADCASTING FUNCTION USING A LOCAL INPUT
- INTERFACE FUNCTION WITH OTHER EQUIPMENT USING A CONTROL INPUT/OUTPUT CONTACT
- Manufacturer: INTER-M
- Category: AMPLIFIERS
- Use: POWER AMPLIFIERS 100V
- Measurement Unit: Attribute34381
- Warranty Months: 12
- Depth (cm): 38.0
- AC Line Voltage and Frequency Configurations Available: 220-240VAC DC24V
- Height (cm): 8.8
- Weight (Kg): 13.0
- Order Quantity: 1
- Power Output: 60
- Rack Installation Possible: Yes
- Channels: 6
- Power Output W/4Ω: 60
- Frequency Response (at 1W, 4/8Ω) (dB) ±: 80Hz-20KHz
- Catalog: Professional
- Amplifier Type: Power Amplifier
- Load Impedance: Ohm
- Group: Attribute49042, Attribute50583
- Width (cm): 48.2
|
Reviews
There are no reviews yet.