Content |
Power Output Level QX4960:
8ohm 1kHz (Quad CH) 170W x 4
4ohm 1kHz (Quad CH) 240W x 4
8ohm 1kHz (bridged mono) 480W x 2
(1kHz, 1% THD)
Input Sensitivity 0.775Vrms
Input Impedance 20kohm Balanced
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz) Less than 0.1%
Signal to Noise Ratio 100dB
Protection Over heat and over current, output short, DC fault
X-Over Frequency 60Hz~2.5kHz
X-Over Cut Off Slope 24dB/Oct
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 770W
Net Weight 17kg/37.5lb
Dimensions 482(W) x 88(H) x369(D) mm
/19(W) x 3.5(H) x14.5(D) mm
Quad Amplifier - 4 Amp Circuit in the One Unit
Substantial Protection Circuitry
Various Display - Power, Protection, Clip and Signal
Mode Switch - Parallel, Stereo and Bridged Mono
Variable Speed Fan Cooling
Input Connectors - Balanced Combination Jack
Output Connectors - 5-Way Binding Post
Built In 2 Way Crossover
|
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
|
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
|
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
RMS, 1kHz, 1.0% THD+N |
|
|
|
|
4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
Pink Noise 12dB CF |
|
|
|
|
4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
|
|
The XM series multi-channel power amplifiers are ideal for theater, hall, and conference room installations. The lineup includes 80W × 4 and 180W × 4 models, meeting the needs of a wide variety of installed systems. The XM amplifiers are a compact 2U size and surprisingly lightweight, making them easy to handle and install. Switching power supplies deliver high output power while minimizing the unit's physical size. The XM series has monitor/remote jacks that allow external devices to be connected for status monitoring or control from a remote location.
Dimensions (W x H x D): 480 x 88 x 412 mm, Weight: 10 kg
Four high-power channels. Switchable stereo, parallel, or bridged operation. Versatile connectivity and high-pass filters for a variety of applications. Distribution drive capability for parallel multi-speakers systems (XM4180).
Monitor/Remote connector for remote monitoring and control.
|
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
Shipping Weight 15 lbs (6.8 kg)
Top
| POWER AMPLIFIER 4 X 2100 WATT / 4Ω
Very high power and channel density – • The four-channel FP
10000Q delivers a total of 10000 W (4 x 2500 W @ 2 ohms) in
only 2U
Four-channel fexibility – • Four channels in one cabinet increases
effciency, fexibility and value in powering monitor systems, line
arrays, and bi- or tri-amped systems. Adjacent channels bridgeable
for 2- or 3-channel operation
Lab.gruppen sound quality – • FP 10000Q amplifers maintain
the impeccable sonic performance standards set by the original fP
Series, with the same durability and even greater effciency
NomadLink • ® network ready – Monitoring and control of key
functions accessible via the intuitive DeviceControl software and
the robust, daisy-chained NomadLink® network
Patented Class TD amplifer topology – • Road-proven output
stage delivers Class B audio quality with Class D effciency
Regulated Switch Mode Power Supply (R.SMPS) – • Output
power remains constant even with signifcant drops in the mains
voltage
Effcient cooling system – • Unique, lightweight Intercooler® cop-
per cooling system dissipates more heat to allow extended peak
output
Adjustable parameters – • Selectable Gain, scalable Voltage Peak
Limiter (VPL), and bridge-mode operation allow custom confgura-
tion for any system or application
XLR input connectors •
Heavy-duty binding post or Speakon output connectors •
Comprehensive protection and warning – • Excessive output
current, DC, high temperature, very high frequency (VHF), short
circuit, open load, mains fuse protection, and soft start |
Reviews
There are no reviews yet.