LAB GRUPPEN ACN3C 3WAY STEREO-4 and 5WAY MONO CROSSOVER

In an active loudspeaker system the crossover network is connected, in the signal path,
before the power amplifiers. An active crossover network feeds separate signals to the
bass, mid, and treble power amplifiers. The power amplifiers in turn power the corresponding
loudspeaker drivers for the bass, mid, and treble ranges.
This method has several advantages, especially in large PA systems, compared to passive
dividing where the crossover network is connected between the power amplifiers and the
loudspeakers. You get for example lower distortion, in particular distortion that is caused by
loud bass tones which intermodulate with the mid, and treble ranges. An active system also
eliminates the power losses, associated with passive crossover networks.

LAB.GRUPPEN's ACN C crossovers are designed around a four-pole state variable filters,
which are derived from the theory of analog computers. The most common way to alter
crossover frequencies in such a circuit is to turn a multiple ganged potentiometer. However
most potentiometers have bad tolerances (20 % or worse), and these tolerances affect the
accuracy of the crossover frequencies and the flatness of the summed output.
A better way of altering the crossover frequency is applied in the ACN 2/3C; namely the use
of "Digital Hexcode" switches. This allows the use of close tolerance components, which
result in a crossover frequency accuracy better than 1 %.
By careful selection of these components, an optimum density of available crossover frequencies
has been created, especially in the region between 800 Hz and 2 kHz. This has made it possible
to achieve a continuity of phase and of group delay time together with the speaker system. This
leads in turn to an improved intelligibility in the vocal region.
12, or 18 dB/octave slopes can be ordered as an option. The 24/octave slope has equal phase
at the crossover frequency region, in accordance with Linkwitz-Riley. To achieve flatness in the
summed output, the high and lowpass filters meet each other at 6 dB.
Each of the outputs of the ACN 2/3C have been equipped with shelving equalization, which gives
an adjustable bass boost of upto +12 dB, and a treble boost of upto +12 dB. In the ACN 3C the
mid output has an additional shelving boost, but that works at a lower corner frequency. With the
help of this equalization it is possible to align the frequency response of the speaker system. You
can, for example, compensate the roll-off in the treble of so-called "Constant Directivity“-type horns.
It also means you negate the need, for an external (graphic) equalizer, in several applications.

Key Features:

3-way stereo or 4- and 5-way mono
Switchable crossover frequencies:
32 frequencies between 80 Hz and 4.8 kHz
No dangerous "x10 switches" or frequency knobs on the front
The standard slope is 24 dB/octave. Optional: 12 and 18 dB/octave slopes
Switchable subsonic filters
Front panel gain controls
Mute switch on all outputs
Mono bass switch
Electronically balanced inputs with transformer option

Lab Gruppen NLB 60E
The NomadLink network provides remote monitoring, control and power sequencing functions for multiple C Series or FP+ amplifiers. Indeed up to 16 NLB 60E network bridges, each monitoring up to 60 amplifiers may be accommodated in one system. Easy setup, redundancy, and minimum maintenance were bywords when developing this network format.

NomadLink is a closed-loop, daisy-chained network topology with the NLB 60E providing the bridge to the familiar world of Ethernet/LAN. NomadLink reduces installation time and cost significantly, includes redundancy during operation by design and simplifies the location of faults or system abuse.

NomadLink together with the associated DeviceControl software allows the subnets’ architecture to be automatically uploaded even without individual IP addresses in the amplifiers. All in all, it is the fastest and easiest monitoring and control network on the market today.

Specifications:

Network Connectors:
   * Nomadlink Out: EtherCon housed RJ45
   * Nomadlink In: EtherCon housed RJ45
   * Ethernet rear-panel: EtherCon housed RJ45
   * Ethernet front-panel: Standard RJ45
General Purpose Inputs (GPI):
   * One Voltage sensing input: Two pole Phoenix
   * Two contact closure inptus: Two pole Phoenix
Front Panel Indicators:
   * Front operation locked: Yellow LED
   * Fault warning: Red LED
   * Amplifier subnet muted: Red LED
   * NomadLink network connected/activity: Blue LED
   * Ethernet connected: Orange LED
   * Ethernet Activity: Yellow LED
2 x 16 Character display: White text, Blue background
Navigation and Adjust keys: Yes, x 6
Subnet Power on/off keys: Yes, x 2
Power: 100 to 240 VAC, 50 to 60 Hz (auto-select)
Power consumption: Finish: Anodized aluminum front, Plated and painted steel chassis
Approvals: CE, CSA
Dimensions (W x H x D): 19" x 1.73" x 8.2" (483 x 44 x 208 mm), 1 RU
Weight: 5 lbs. (2.25 kg)

Providing 48-bit filter algorithms, 24-bit AD/DA conversion and a dynamic range of 115 dB, the DSP 244 sets new standards for digital loudspeaker controllers and processors. The DSP 244 is an universal Digital Sound System Processor that provides 2 inputs and 4 outputs; plus internal summing of the inputs 1 and 2. Via matrix it is possible to assign the outputs to any input or to the sum of the inputs. It is further possible to establish the following configurations: Stereo or Dual 2-Way systems, 3-Way + Direct and 4-Way systems, each with Mono Subchannel, but also full range systems. High and low-pass filters are provided for the frequency crossover functions in all operation modes. The selection includes Linkwitz-Riley, Butterworth and Bessel type filters with switchable slopes between 6, 12, 18 and 24 dB/oct. A huge number of additional filters offers extremely flexible correction of the frequency response. Each input incorporates a 5-band equalizer, allowing to assign high and low-pass, high and low-shelving or parametric peak-dip filters to its individual filter sections. Next to the frequency crossover filters, four additional filters are employed in each output channel, which also can be set to work as high or low-pass, high or low-shelving filters, parametric peak-dip filters, or all-pass filters. Additional filtering is provided through 2. order high-passes for the realization of B-6 alignment, or special LPN-filters (Low-Pass Notch filters) for correcting the frequency and phase responses of optimally vented woofer cabinets. Each channel additionally provides a delay, a polarity switch, a programmable level control and a digital compressor / limiter while the master delays are located in the input channels. Datasheets / ManualsBrochure (309KB)

Mains voltage 90 - 250 V AC / 50 - 60 Hz Power consumption 20 watts Safety class I Inputs 2 x XLR IN, electronically balanced, transformer optional available 2 x XLR OUT (Direct Out) Input voltage (nominal) 1.55 V / + 6 dBu Max. input voltage 24.5 V / + 30 dBu Input impedance 20 kohms Common mode rejection > 40 dB AD-conversion 24-bit, Sigma-Delta, 128 times oversampling, linear phase Outputs 4 x XLR OUT, electronically balanced Output voltage (nominal) 1.55 V / + 6 dBu Max. output voltage 8.7 V / + 21 dBu Output impedance

The LD DPA260 is a 6-Channel 19" Speaker Processor for our VA-4, VA-8 and UNO-Array with plenty of useful setups for each system

• Type: DSP Controller for Line Array VA-4, VA-8 and UNO
• Model Name: DPA-260
• Description: 6-Channel 19" speaker processor, 32bit DSP, 24bit AD/DA (48 kHz) converter
• Inputs: 2 Channels Analog/Digital, L + R, Noise Gate, the inputs and outputs are freely assignable, that means you can assign any input to any output and vice versa
• Input EQ: 5 Band PEQ, Low Shelf and High Shelf Types available
• Crossover Range: 20 Hz - 20 kHz
• Outputs: 6 Channels, High/Low Pass Filter, Filtertype and dB available, 7 Band PEQ, Low Shelf and High Shelf Types available, Limiter with Threshold, Attack and Release Parameters
• Delay: Time or Meter available, Max. Delay up to 848 ms
• Phase Invert Function: USB Port, Full programmable Software included with 24 Memory Capacity for Presets
• Display: 2 × 16 character LCD with backlight
• Switch mode power supply: 90 V - 250 V
• Dimensions:    19" / 1U

With 12 inputs and 6 outputs and Ethernet control the dbx ZonePro? 1260 and 1261
are the newest members of the ZonePro? family providing a complete suite of signal
processing and control for Commercial Audio applications.
Designed to offer superior system sonic performance and flexibility, the 1260/1261 deliver
the highest quality tools available. Even the input and outputs connectors were chosen for
their standard usage and reliability. The ZonePro products offer Euroblock connectors for
balanced signals and RCA connectors for interfacing with consumer equipment often used
in commercial applications; there is also a simple analog input buss that allows inputs to be
sent from one unit to the next for unit and job scalability. The 1260 and 1261 provide every
necessary processing tool, from the input processing like gain control and EQ available on all
inputs to highly sophisticated and specific functions such as selectable paging microphone
processing including Gating, De-Essing, Auto Gain Control, Compression and Feedback
Suppression. The heart of the ZonePro products is the Routing module that provides of course
Primary Source Selection but also Source Ducking for Paging and Priority Override. The outputs
also offer a wealth of processing designed for commercial applications like our patent-pending
AutoWarmth? function that was co-developed with JBL to provide natural low frequency extension
at any signal level. Each output also offers EQ, Bandpass and Crossover filters, Limiting and Delay
for system optimization. With the ZonePro? every tool is at your disposal to maximize the response
of your system.
Beyond processing, the ZonePro? products offer multiple forms of control to further extend the
versatility of your system. From easy-to-use wall panel Zone Controllers for standard end-user
functions like source select and volume control to advanced system control including a built-in
Real Time Clock that can provide programmable system changes throughout the day or week.
For system setup and monitoring the ZonePro Designer software provides an intuitive interface
and a speedy setup Wizard for configuring and editing all system parameters. The addition of
Ethernet control means that not only will it work with standard network equipment, but it can also
be accessed from remote dialup locations or from wireless access points.
The ZonePro? 1260 and 1261 will take your Commercial Audio system to the next level with advanced
processing, versatility and control.
 
? Advanced Feedback Suppression (AFS?)
? Autowarmth?
? Auto Gain Control
? Compression
? Limiting
? Noise Gating
? Notch Filtering
? Bandpass and Crossover Filters
? Parametric EQ
? Security Lockout
? Wall Panel Control
? RS-232 Control
? IEC, UL and CSA Approvals
 
ZonePro? 1260/1261 Specifications    
      
ANALOG INPUT
Number of Inputs:
12 Total (2) Switchable mic or line, (8) RCA, and (1)
S/PDIF
Connectors:
Euroblock (Line and Mic) RCA (Source)
Type:
Impedance (Euroblock):
> 50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):
>25kΩ Unbalanced, RF Filtered
Max input line level:
+20dBu Mic/Line, +12dBu RCA
CMRR:
> 40dB, typically >55db @ 1kHz
Mic Pre gain:30 to 60dB
Mic EIN:
> 118dB, 22Hz-22kHz, 150Ω Source Impedance
Mic Phantom Power:
15V
 
ANALOG OUTPUTS
Number of Outputs 6
Connectors: Euroblock
Type:
Electronically balanced, RF filtered
Impedance:
120 ohms balanced, 60ohm unbalanced
Max Output Level: +20dBu
 
A/D PERFORMANCE
Type:
dbx Type IV? conversion system
Dynamic Range line:
>113 dB, A-weighted, >110 dB unweighted
Type IV dynamic range:
>119 dB, A-weighted, 22kHz BW
>117 dB, A-weighted, 22kHz BW
Sample Rate: 48kHz
 
D/A PERFORMANCE
Dynamic Range:
112 dB A-weighted, 109dB unweighted
 
SYSTEM PERFORMANCE
Dynamic Range:
>110 dB A-weighted, >107dB unweighted
THD+N:
0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response:
20Hz - 20kHz, +/-0.5dB
Interchannel Crosstalk:
>80dB typical
Crosstalk input to output:
>80dB
Propagation Delay
0.6 msec
 
POWER REQUIREMENTS
Operating Voltage:
100-240 VAC, 50/60Hz
Power Consumption:
27 Watts
 
Physical:
Weight:
6.8 lbs.(3.1 kg) Shipping weight 8.8 lbs. (4.0 kg)
Dimensions:
1.75? H x 5.75? D x 19? W