LAB GRUPPEN iP 1350 2X500W POWER AMPLIFIER

The iP 1350 is a space-saving power amplifier, ideal for use in installations as well as
in cost-effective live sound systems.
The Iron Power (iP) family of power amplifiers is the new compact and versatile line of
professional power amplifiers with classic toroidal iron transformers. To achieve a compact
design, the latest semiconductor technology is utilized. This, together with Lab.gruppen?s
proprietary copper cooling system, Intercooler?, enhances the 2 ohms capacity. A new
Bi-phase wiring scheme also increases the capacity of the power supply. This extends
the power bandwidth in the low end.

Key Features:
2 x 300 watts @ 8 ?
2 x 500 watts @ 4 ?
2 x 700 watts @ 2 ?
(Measured just below clip level, with both channels driven)
Compact design: 2U high
Intercooler? cooling system with front-to-rear airflow
Multiple positions gain switch
Easily accessible dust filter
Improved low-end power bandwidth
Neutrik Combo jack and Phoenix terminal block input connectors
Bridged mono outputs in one SpeakOn connector

Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of features to
make the iP family functional in all situations from installation to cost-effective live sound systems:

Multiple positions Gain switch
To meet the demands for a flexible gain structure in the system, Lab.gruppen offers a multiple
position gain switch. The maximum amplifier gain can be set to all industry standards: 20, 23, 26,
29, 32, 35, 38 and 41 dB.

Versatile input connection
With the Neutrik Combo-jack we offer both the professional XLR-type standard and the semi-pro
1/4? TRS phono-jacks. For installations the 3-pin Phoenix terminal block may be handier.

Soft Start
Toroidal transformers require a huge amount of start current to build up a magnetic flux when the
amplifier is switched on. Therefore Lab.gruppen have included a soft start circuit to minimize the
risk of blowing the wall fuse and to reduce flickering in the lighting.

Sophisticated protection circuitry, combining:
ALS? short circuit protection; the Adaptive Limiting System permits very high peak currents, but
keeps the amplifier within the Safe Operation Area.
DC protection; protects against infrasonic signals
VHF protection; protects the loudspeakers against strong very high frequency non-musical signals
above the audible range.
Thermal protection; prevents the amplifier from being overheated. The protection indicators on the
front panel are switched on, as a warning, before the protection process is initiated.
AC protection; shuts down the power supply if the line voltage is outside the operating voltage.
Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining
full peak power.

Engineered from the ground up for unmatched quality and performance,
the Crown? DSi Series of power amplifiers offers three models of 500W,
800W, and 1200W per channel at 4 ohms. Onboard digital signal processing
includes crossovers, EQ filters, delay and output limiting. Rear panel HD-15
connector provides easy input/output connectivity between DSi amplifiers
and the new DSi-8M System Monitor.
The intuitive front panel LCD screen guides installers through a setup process?
featuring presets for the industry-standard JBL cinema loudspeaker systems?
to make configuration quick and easy.
At the touch of a button, Crown?s DSi cinema amplifiers deliver perfectly matched
performance with each award-winning JBL ScreenArray? system, making this the
ultimate cinema solution.

Features :
Includes three models of 500W, 800W, and 1200W per channel at 4 ohms
Automatic presets for popular JBL cinema speaker systems for quick, easy
configuration
Intuitive front-panel LCD screen guides installers through setup
Onboard digital signal processing includes crossovers, EQ filters, delay, and
output limiting
Computer connectivity via USB allows fast setup and configuration with HiQnet?
System Architect? software
Rear-panel HD-15 connector provides easy input/output connectivity between DSi
amplifiers and new DSi-8M System Monitor
Switch-mode universal power supply
All products fill 2U rack spaces and weigh under 19 pounds
Barrier strip outputs, removable Phoenix-style input
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment
and guarantees its specifications

The Crown? DSi 1000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, fl ashes when a very low-level
signal is present at input.
?10 Indicator: Green LED flashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED flashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or
excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 700W with 1% THD, 4 ohm Stereo
(per channel): 500W with 0.5% THD, 8 ohm Stereo (per channel) 275W with
0.5% THD, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono:
1,000W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 2.35V.
Sensitivity at 4 ohm rated output: 2.24V.
Sensitivity at 2 ohm rated output: 1.88V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.5A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
EQ: 6 parametric fi lters per channel with adjustable Q, boost/cut ±15 dB. Also
adjustable high and low shelving fi lters.
Filters: Highpass and lowpass per channel. Butterworth 12/18 dB per octave
and Linkwitz-Riley 24 dB per octave. High and low shelving fi lters, one per
channel.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 5 user-defi nable loudspeaker presets and 15 factory-default JBL
system presets.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)

InterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm bridge 1200W/4ohm 10-83kHz

high pass filter 30Ηz & 50Ηz

A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange, and superbly defined highs. They also deliver fast response and exceptional stability even in the face of serious power supply limitations. Refinements throughout this expanded five-model lineup make these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 250 Watt / 8Ω RMS, 2 x 450 Watt / 4Ω RMS, 900 Watt / 8Ω bridge RMS. Weight: 12,5 Kg.

• Output power: 450W @ 4 Ohms stereo, 280W @ 8 Ohms stereo
• High-current toroidal transformers for greater power and low noise
• Independent user-defeatable peak limiters reduce distortion
• Selectable High-Pass filter at 30Hz or 50Hz
• XLR and 1/4' TRS input jacks
• Binding post and Speakon?-type outputs
• Front mounted gain controls for easy access
• Signal and Peak LED indicators to monitor performance
• Short circuit, thermal, subsonic, RF protection, output DC offset
• Power on/off muting

The model L 500 is a 2 x 250 Watts Power Amplifier. Linear Precision Series
power amps combine excellent audio performance, modern and innovative
circuit design, meticulous and exceptionally rigid construction, and the highest
levels of operational integrity and reliability with an appropriate and more than
realistic price. The robust steel chassis provides outstanding torsional strength
through L-shaped side panels reaching under the thick aluminium front panel.
Thermal breakers prevent the power supply units from being damaged by thermal
overload. Electronically controlled fans provide sufficient front-to-rear airflow and
a special cool air diverter takes care of thermal stability. The fans? noise-level is
extremely low which provides the possibility for studio use. If necessary, a supplied
air-filter can be mounted behind the front panel ventilation louvres.
 
Features
* Excellent audio performance
* Symmetrical topology
* Ultra-low distortion
* Generously dimensioned power supply units
* Suitable to be operated on loads down to 2 ohms
* Suitable to drive complex loads with phase angles of ± 90 degree
* Extensive protection circuitry
* Unique Back-EMF protection
* Switchable limiters
* Switchable Hi/Lo-Cut filters
* Robust steel chassis
* Exceptional low noise front-to-rear air-flow
* XLR-type inputs and direct-outs
* LED display shows On, In, Out, Limit and Protect
* Highly reliable operation

Specs
* Max. Output Power - into 8 ohms : 2 x 180 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 4 ohms : 2 x 280 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 2 ohms : 2 x 320 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 8 ohms bridged : 1 x 560 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 4 ohms bridged : 1 x 640 W at 1 kHz / THD = 1.0%
* Rated Output Power - into 8 ohms : 2 x 175 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 4 ohms : 2 x 250 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 2 ohms : 2 x 300 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 8 ohms bridged : 1 x 500 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 4 ohms bridged : 1 x 600 W at 20 Hz - 20 kHz / THD = 0.1 %
* Frequency Response : 0 dB ..... -1 dB/20 Hz - 20 kHz
* Phase Angle Response : ± 30 degree/20 Hz.....20 kHz
* Maximum Output Level : 45 V / RMS before clipping, no load, ref. 1 kHz / THD = 1%
* Voltage Gain ref. 1 kHz : 26 dB (constant gain option)
* Input Sensitivity : 0 dBu/0.775 V, +6 dBu/1.55 V at rated output / 4 ohms ref. 1 kHz
* Maximum Input Level : +21 dBu / 8.7 V
* Input Impedance active balanced : 20 kohms
* THD at Rated Output : < 0.05 % MBW = 80.0 kHz, f = 1 kHz
* IMD -SMPTE : < 0.01 % 60 Hz, 7 kHz, at rated output
* Signal-to-Noise Ratio : >105 dB at rated output into 4 ohms,
   A-weighted, RMS, input sensitivity +6 dBu
* Attenuation at rated output : > 70 dB f = 1 kHz
* Damping Factor internal 1 kHz : > 300
* DIM 30 : < 0.01 %
* DIM 100 : < 0.01 %
* Slew Rate internal : > 25 V / ?s
* Power Consumption : 300 W 1/8 rated output into 4 ohms
* Width : 483 mm
* Height : 88.1 mm
* Depth : 426 mm
* Weight : 14 kg