Content |
The iP 1350 is a space-saving power amplifier, ideal for use in installations as well as in cost-effective live sound systems. The Iron Power (iP) family of power amplifiers is the new compact and versatile line of professional power amplifiers with classic toroidal iron transformers. To achieve a compact design, the latest semiconductor technology is utilized. This, together with Lab.gruppen?s proprietary copper cooling system, Intercooler?, enhances the 2 ohms capacity. A new Bi-phase wiring scheme also increases the capacity of the power supply. This extends the power bandwidth in the low end.
Key Features: 2 x 300 watts @ 8 ? 2 x 500 watts @ 4 ? 2 x 700 watts @ 2 ? (Measured just below clip level, with both channels driven) Compact design: 2U high Intercooler? cooling system with front-to-rear airflow Multiple positions gain switch Easily accessible dust filter Improved low-end power bandwidth Neutrik Combo jack and Phoenix terminal block input connectors Bridged mono outputs in one SpeakOn connector
Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of features to make the iP family functional in all situations from installation to cost-effective live sound systems:
Multiple positions Gain switch To meet the demands for a flexible gain structure in the system, Lab.gruppen offers a multiple position gain switch. The maximum amplifier gain can be set to all industry standards: 20, 23, 26, 29, 32, 35, 38 and 41 dB.
Versatile input connection With the Neutrik Combo-jack we offer both the professional XLR-type standard and the semi-pro 1/4? TRS phono-jacks. For installations the 3-pin Phoenix terminal block may be handier.
Soft Start Toroidal transformers require a huge amount of start current to build up a magnetic flux when the amplifier is switched on. Therefore Lab.gruppen have included a soft start circuit to minimize the risk of blowing the wall fuse and to reduce flickering in the lighting.
Sophisticated protection circuitry, combining: ALS? short circuit protection; the Adaptive Limiting System permits very high peak currents, but keeps the amplifier within the Safe Operation Area. DC protection; protects against infrasonic signals VHF protection; protects the loudspeakers against strong very high frequency non-musical signals above the audible range. Thermal protection; prevents the amplifier from being overheated. The protection indicators on the front panel are switched on, as a warning, before the protection process is initiated. AC protection; shuts down the power supply if the line voltage is outside the operating voltage. Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining full peak power. | The LD Systems DP600 Power Amplifier offers an amplifiying level of 2 x 300 W 2 Ohm
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 400 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
800 W
Frequency response
20 - 20000 Hz
Signal-to-noise ratio
105 dB
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
Controls
2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal
Speaker output connections
Speakon compatible , Terminal posts
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
Features
Volex mains socket
|
VLP Series Power Amplifier
Output Power:
- 150W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
- 100W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
(Bridge Mode, Mono)
- 300W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 260
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift
Dimensions (LxWxH): 13.25" x 19" x 1.75" / 336 x 482 x 44mm (1-rack mount space)
Weight: 24 lbs. / 11Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange, and superbly defined highs. They also deliver fast response and exceptional stability even in the face of serious power supply limitations. Refinements throughout this expanded five-model lineup make these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 250 Watt / 8Ω RMS, 2 x 450 Watt / 4Ω RMS, 900 Watt / 8Ω bridge RMS. Weight: 12,5 Kg.
|
VLP Series Powere Amplifier
Output Power: 300W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD 200W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD (Bridge Mode, Mono) 600W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 300
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift Limiter
Dimensions (LxWxH): 14" x 19" x 3.5" / 360 x 482 x 88mm 2-rack mount spaces
Weight: 33 lbs. / 15 Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift; Limiter
|
Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 900 W, 4 Ω - 600 W, 8 Ω - 380 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1700 W, 4 Ω - 950 W, 8 Ω - 480 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1800 W, 8 Ω - 1200 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +3.1 dBu (1.11 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 14.8 kg (32.6 lbs)
|
Reviews
There are no reviews yet.