The new Audio 3-stage CLASS-H SMPS amplifiers incorporate all the features to meet all your needs, whether youʼre starting a P.A. amplifier project from scratch or just need to upgrade your present sound reinforcement equipment. In the amps, youʼll find 2 and 4 channel models, all offering high power levels at low distortion in the […]
The new Audio 3-stage CLASS-H SMPS amplifiers incorporate all the features to meet all your needs, whether youʼre starting a P.A. amplifier project from scratch or just need to upgrade your present sound reinforcement equipment. In the amps, youʼll find 2 and 4 channel models, all offering high power levels at low distortion in the range 1.5 to 6 kW, yet weighing around 8.6 kg and only 30 cm deep.
Model Name: SP2K4
Output Power 1 kHz, 500
Crosstalk (20 Hz – 20 kHz): > 75 dB
Voltage Gain (selectable): 26/32/38 dB
Input Sensitivity: 3.0 / 1.5 / 0.8 V
Protection: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, ICL (Inteligent Clip Limiting), PMS (Power Management System), SSP (SOA Sentry Protection)
Controls: On / Off Switch, Volume, Voltage Gain, Dual / Link Switchable, Bridge Mode Configuration Switch
The new Audio 3-stage CLASS-H SMPS amplifiers incorporate all the features to meet all your needs, whether youʼre starting a P.A. amplifier project from scratch or just need to upgrade your present sound reinforcement equipment. In the amps, youʼll find 2 and 4 channel models, all offering high power levels at low distortion in the range 1.5 to 6 kW, yet weighing around 8.6 kg and only 30 cm deep.
Model Name: SP2K4
Output Power 1 kHz, 500
Crosstalk (20 Hz - 20 kHz): > 75 dB
Voltage Gain (selectable): 26/32/38 dB
Input Sensitivity: 3.0 / 1.5 / 0.8 V
Protection: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, ICL (Inteligent Clip Limiting), PMS (Power Management System), SSP (SOA Sentry Protection)
Controls: On / Off Switch, Volume, Voltage Gain, Dual / Link Switchable, Bridge Mode Configuration Switch
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
OUTPUT POWER
S-1500
S-2000
S-3000
S-4000
S-6000
S-3004
S-4004
S-4044
S-6004
S-6044
1kHz, 1.0% THD
2 ohms
2x880W
2x1190W
2x1570W
2x1950W
2x2950W
4x700W
4x980W
-
4x1440W
-
4 ohms
2x575W
2x790W
2x1100W
2x1380W
2x2025W
4x500W
4x670W
4x975W
4x1000W
4x1480W
8 ohms
2x325W
2x460W
2x630W
2x810W
2x1250W
4x300W
4x430W
4x690W
4x620W
4x1015W
Bridge @ 4ohms
1760W
2380W
3140W
3900W
5900W
2x1400W
2x1960W
-
2x2880W
-
Bridge @ 8ohms
1150W
1580W
2200W
2760W
4050W
2x1000W
2x1340W
2x1950W
2x2000W
2x2960W
P. N. 12dB C.F.
2 ohms
2x975W
2x1360W
2x2060W
2x2460W
2x4225W
4x890W
4x1170W
-
4x2080W
-
4 ohms
2x610W
2x880W
2x1240W
2x1600W
2x2600W
4x580W
4x820W
4x1230W
4x1280W
4x2110W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™
This professional stereo power amplifier, working in class-H mode, provides 2x800W, at an efficiency of around 85%.
A passive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode. The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling. The integral soft clip limiter protects against damage to the connected loudspeakers. The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 2Ω:
2 x 800 Watt rms
Power output stereo 4Ω:
2 x 650 Watt rms
Power output stereo 8Ω:
2 x 350 Watt rms
Power output bridged 4Ω:
1600 Watt rms
Power output bridged 8Ω:
1300 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 103 dB
Crosstalk:
> 70 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
200:1 (8 Ω)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
20.000 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Temperature, DC, RFI short circuit, Soft-Start, Thermal on transformer
POWER REQUIREMENT
Operating voltage:
220÷240 / 110÷120 ~ 50 / 60 V ~ Hz
Max.current:
7.5 A
Power Consumption:
2700 W
PHYSICAL SPECIFICATIONS
Height:
88 / 3.46 mm/inch
Width:
483 / 19.01 mm/inch
Depth:
455 / 17.91 mm/inch
Net Weight:
19.5 / 42.98 Kg/Lbs
SHIPPING INFORMATION
Package height:
150 / 5.9 mm/inch
Package width:
555 / 21.85 mm/inch
Package depth:
525 / 20.66 mm/inch
Shipping Weight:
20 / 44.09 Kg/Lbs
Crown DSi 2000 2x800W-4Ω Power Amplifier
The Crown? DSi 2000 power amplifier shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifier and the DSi-8M System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifier shall have the following specifications:
with 0.5% THD, 4 ohm Bridge-Mono: 2,000W with 1% THD, 8 ohm Bridge-
Mono: 1,600W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.09V.
Sensitivity at 4 ohm rated output: 2.84V.
Sensitivity at 2 ohm rated output: 2.24V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms,unbalanced.
Maximum Input Signal: +22 dBu typical.
Number of Channels: 2
Output Power: (per channel)
8 ohms 450W
4 ohms 850W
2 ohms 1550W
Output Power: (bridged)
8 ohms 1700W
4 ohms 3100W
THD%: (@1dB below max output)
@ 1kHz
Crownʼs new CTs series of power amplifiers are remarkable for their loud, punchy sound; sustained, tight bass; and superior protection against overheating and overload. This paper explains the design features behind those advantages. After reading this information, youʼll know why Crown CTs amps sound better than the competition. CTs amplifiers can provide large amounts of power into various loads, such as 2, 4, 8 ohms and 70V. With most power amps, the maximum output power tends to drop as the load impedance increases. But with the CTs series, the power stays the same at almost any impedance. 2-ohm Dual (per Ch.) 250W 4-ohm Dual (per Ch.) 600W 8-ohm Dual (per Ch.) 600W 16-ohm Dual (per Ch.) 300W 70V Dual (per Ch.) 600W 4-ohm Bridge 500W 8-ohm Bridge 1200W 16-ohm Bridge 1200W 140V Bridge 1200W Crown switching power supply for less weight Sustained Power on long-duration signals due to regulated, "stiff” power supplies with incredible energy storage (huge filter capacitors). Extra Hidden Power during high-level transients and during incomplete use of all the channels. Overheating and overload protection thanks to the sophisticated TLC circuitry which compresses the signal only when needed. Compression is controlled not by temperature, but by signal voltage. This keeps the loudness up during compression more than with competitive amps.
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.