| Content |
LD Premium LDSP44K 4-Channel Power Amplifier
The LDSP44K is a professional 4-channel power amplifier offering amazing value and versatility in a compact lightweight Class H design. Suitable for touring and installation sound reinforcement it delivers a maximum of 4x 980W into 2Ohms and 2x 1.960 in 4Ohms stereo bridge mode.
Featuring a high efficiency switch mode power supply the LDSP44K provides a 20Hz – 20kHz bandwidth with low THD and crosstalk, a damping factor higher than 500, excellent S/N ratio and 3 switchable sensitivity levels.
Reliable performance is ensured by heavy duty engineering, high quality components and comprehensive protection including soft start with turn-on muting, PMS™ power management, SSP™ (Safe operation Sentry Protection) and ICL™ (Intelligent Clip Limiting) to maintain signal integrity. Protection circuits against DC, thermal and power supply overload are implemented. A switchable subsonic filter and a 3-position gain switch offer variable amplifier adjustment.
- Type: Professional Power Amplifier
- Model Name: SP44K
- Output Power 1 kHz,
- 2 ohms 4 x 980 W
- 4 ohms 4 x 670 W
- 8 ohms 4 x 430 W
- Bridge 4 ohms 2 x 1960 W
- Bridge 8 ohms 2 x 1340 W
Output Circuity: Class H
Frequency Range: 20 Hz - 20 kHz THD: S/N Ratio: 113 dB Damping Factor: >500 Crosstalk: > 75 dB Voltage Gain: 26 / 32 / 38 dB Input Sensitivity: 3.0 / 1.5 / 0.8 V Input Impedance: 20k ohm (balanced) / 10k ohm (unbalanced) Protection: Soft-start, Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short circuit, Open or mismatched loads, Overloaded power supply, ICL Clip Limiter, PMS, SSP
Controls: On/Off, Volume, Voltage Gain, Dual / Link switchable, Bridge / Stereo configuration switch Indicators: Signal, Temp, PMS (Power Management System), ICL (Intelligent Clip Limiting) Connectors: Input: XLR / Output: Neutrik Speakon Cooling System: 2 x continuously variable speed fan, rear to front
Power Supply: AC~230V / 50 Hz
Power Consumption Full Load: 13.5 A Dimensions (W x H x D): 483 x 89 x 310 mm |
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
|
Power Output Level: QD4240
8ohm (Quad Ch) 40W
4ohm (Quad Ch) 60W
8ohm bridged mono 120W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
|
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
|
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
| RMS, 1kHz, 1.0% THD+N |
|
|
|
|
| 4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
| 8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
| Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
| Pink Noise 12dB CF |
|
|
|
|
| 4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
|
|
Amplifier Gain 32 dB (Lo-Z), 33 dB (70V), 36 dB (100V)
Analog Inputs 4, electronically balanced, Phoenix-type
Audio Network No
CAN Bus Interface Yes (With Optional RCM-810 Card)
Continuous Rated Power
(1 kHz, THD 1%) 100v 1000 Watts
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 1000 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 1000 Watts
Continuous Rated Power
(1 kHz, THD 1%) 70v 1000 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 500 Watts
Continuous Rated Power
(20-20 kHz, THD Continuous Rated Power
(20-20 kHz, THD Continuous Rated Power
(20-20 kHz, THD Continuous Rated Power
(20-20 kHz, THD Cooling Front-to-Rear, continuously variable fans
DIM 30 0.02 %
Electronics Type Amplifier
Frequency Response 15 Hz-30 kHz
Input Impedance (Balanced) 20 kΩ
Input Sensitivity 0 dBu (.775V)-2 Ω, +3 dBu (1.1V)-4/8 Ω, +6 dBu (1.55) 70V/100V
Intermodulation Distortion (SMPTE) 0.05 %
Mains Voltage 220 - 240 V, 50 - 60 Hz or 120 V, 50 - 60 Hz, 50 - 60 Hz
Network Control (IRIS-Net) Optional
Total Harmonic Distortion 0.05 %
Variable Load Drive (VLD) Yes
Height 2RU 88.1 mm (3.47“)
Width 483 mm (19.02“)
Depth 421.5 mm (16.59“)
Weight Net 11.1 kg (24.47 lbs) ![aposirsi_electrovoice]( "aposirsi_electrovoice")
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
| 1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
| 2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
| 4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
| 8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
| Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
| Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
| P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
| 2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
| 4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
Reviews
There are no reviews yet.