Content |
LD Premium LDSP44K 4-Channel Power Amplifier
The LDSP44K is a professional 4-channel power amplifier offering amazing value and versatility in a compact lightweight Class H design. Suitable for touring and installation sound reinforcement it delivers a maximum of 4x 980W into 2Ohms and 2x 1.960 in 4Ohms stereo bridge mode.
Featuring a high efficiency switch mode power supply the LDSP44K provides a 20Hz – 20kHz bandwidth with low THD and crosstalk, a damping factor higher than 500, excellent S/N ratio and 3 switchable sensitivity levels.
Reliable performance is ensured by heavy duty engineering, high quality components and comprehensive protection including soft start with turn-on muting, PMS™ power management, SSP™ (Safe operation Sentry Protection) and ICL™ (Intelligent Clip Limiting) to maintain signal integrity. Protection circuits against DC, thermal and power supply overload are implemented. A switchable subsonic filter and a 3-position gain switch offer variable amplifier adjustment.
- Type: Professional Power Amplifier
- Model Name: SP44K
- Output Power 1 kHz,
- 2 ohms 4 x 980 W
- 4 ohms 4 x 670 W
- 8 ohms 4 x 430 W
- Bridge 4 ohms 2 x 1960 W
- Bridge 8 ohms 2 x 1340 W
Output Circuity: Class H
Frequency Range: 20 Hz - 20 kHz THD: S/N Ratio: 113 dB Damping Factor: >500 Crosstalk: > 75 dB Voltage Gain: 26 / 32 / 38 dB Input Sensitivity: 3.0 / 1.5 / 0.8 V Input Impedance: 20k ohm (balanced) / 10k ohm (unbalanced) Protection: Soft-start, Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short circuit, Open or mismatched loads, Overloaded power supply, ICL Clip Limiter, PMS, SSP
Controls: On/Off, Volume, Voltage Gain, Dual / Link switchable, Bridge / Stereo configuration switch Indicators: Signal, Temp, PMS (Power Management System), ICL (Intelligent Clip Limiting) Connectors: Input: XLR / Output: Neutrik Speakon Cooling System: 2 x continuously variable speed fan, rear to front
Power Supply: AC~230V / 50 Hz
Power Consumption Full Load: 13.5 A Dimensions (W x H x D): 483 x 89 x 310 mm |
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
|
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
| • Eight and four channel models with 300W and 150W per channel • Minimal footprint and mass arround 200mm depth and 6 Kg • Optional Add-on card to interface with third party alarm systems with GPIO connections • FCM™ Faulty Channel Management system to avoid entire device shutdown • State-of-the-art layout for maximum performance and reliability • Highly oversized thermal dissipation design for maximum reliability • Superb distortion and noise figures • All channels bridgeable by pairs • Selectable gain in four channel groups (26, 32 and 38dB) • Subsonic filter per channel (35Hz user selectable) • Temperature and signal dependant, intelligent cooling system for minimal noise • Optimal heat extraction due to the air tunneled enclosure and insulator-less power device attachment to the heatsink • Direct connector-less output for maximum quality loudspeaker control • High grade engineering inside with the latest SMD technology • Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection • Critical electronic and mechanical parts selection • Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection • Detented and optionally tamper-proof volume potentiometers • Hi efficiency, two steps Class H Audio topology • Protection, Signal and Clip indicators per channel • Power On and Standby general indicators • Extremely compact, fully featured QuantaPulse Power supply • Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations • Factory preset worldwide mains voltage power supply • Laser cut four milimeters aluminium front panel • Rugged 2U steel chasis
|
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
RMS, 1kHz, 1.0% THD+N |
|
|
|
|
4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
Pink Noise 12dB CF |
|
|
|
|
4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ | - 6CH 60W DIGITAL AMPLIFIER
- LIGHT WEIGHT
- 6 BUS BROADCASTING FUNCTION WITH A UTP (CATEGORY 5) CABLE.
- VOLUME AND 5 BAND EQ TUNING FUNCTION BY CHANNEL
- AMP ID AUTO/MANUAL ALLOCATION FUNCTION
- SELF-BROADCASTING FUNCTION USING A LOCAL INPUT
- INTERFACE FUNCTION WITH OTHER EQUIPMENT USING A CONTROL INPUT/OUTPUT CONTACT
- Manufacturer: INTER-M
- Category: AMPLIFIERS
- Use: POWER AMPLIFIERS 100V
- Measurement Unit: Attribute34381
- Warranty Months: 12
- Depth (cm): 38.0
- AC Line Voltage and Frequency Configurations Available: 220-240VAC DC24V
- Height (cm): 8.8
- Weight (Kg): 13.0
- Order Quantity: 1
- Power Output: 60
- Rack Installation Possible: Yes
- Channels: 6
- Power Output W/4Ω: 60
- Frequency Response (at 1W, 4/8Ω) (dB) ±: 80Hz-20KHz
- Catalog: Professional
- Amplifier Type: Power Amplifier
- Load Impedance: Ohm
- Group: Attribute49042, Attribute50583
- Width (cm): 48.2
|
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuit. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Rated ouput power (1kHz @ 4 Ohms)
4 x 810 W
Rated ouput power (1kHz @ 8 Ohms)
4 x 490 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
2 x 1600 W
Frequency response
20 - 20000 Hz
Total Harmonic Distortion (THD)
< 0.1 %
Signal-to-noise ratio
105 dB
Input sensitivity
0.775 V
Protection circuits
DC protection , short circuit , thermal overload
Controls
4 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
Limit , Power , Protect (protection circuit engaged) , Signal
Speaker output connections
Speakon compatible
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
|
Reviews
There are no reviews yet.