| Content |
LD Premium LDSP44K 4-Channel Power Amplifier
The LDSP44K is a professional 4-channel power amplifier offering amazing value and versatility in a compact lightweight Class H design. Suitable for touring and installation sound reinforcement it delivers a maximum of 4x 980W into 2Ohms and 2x 1.960 in 4Ohms stereo bridge mode.
Featuring a high efficiency switch mode power supply the LDSP44K provides a 20Hz – 20kHz bandwidth with low THD and crosstalk, a damping factor higher than 500, excellent S/N ratio and 3 switchable sensitivity levels.
Reliable performance is ensured by heavy duty engineering, high quality components and comprehensive protection including soft start with turn-on muting, PMS™ power management, SSP™ (Safe operation Sentry Protection) and ICL™ (Intelligent Clip Limiting) to maintain signal integrity. Protection circuits against DC, thermal and power supply overload are implemented. A switchable subsonic filter and a 3-position gain switch offer variable amplifier adjustment.
- Type: Professional Power Amplifier
- Model Name: SP44K
- Output Power 1 kHz,
- 2 ohms 4 x 980 W
- 4 ohms 4 x 670 W
- 8 ohms 4 x 430 W
- Bridge 4 ohms 2 x 1960 W
- Bridge 8 ohms 2 x 1340 W
Output Circuity: Class H
Frequency Range: 20 Hz - 20 kHz THD: S/N Ratio: 113 dB Damping Factor: >500 Crosstalk: > 75 dB Voltage Gain: 26 / 32 / 38 dB Input Sensitivity: 3.0 / 1.5 / 0.8 V Input Impedance: 20k ohm (balanced) / 10k ohm (unbalanced) Protection: Soft-start, Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short circuit, Open or mismatched loads, Overloaded power supply, ICL Clip Limiter, PMS, SSP
Controls: On/Off, Volume, Voltage Gain, Dual / Link switchable, Bridge / Stereo configuration switch Indicators: Signal, Temp, PMS (Power Management System), ICL (Intelligent Clip Limiting) Connectors: Input: XLR / Output: Neutrik Speakon Cooling System: 2 x continuously variable speed fan, rear to front
Power Supply: AC~230V / 50 Hz
Power Consumption Full Load: 13.5 A Dimensions (W x H x D): 483 x 89 x 310 mm |
High-tech in professional amplification!
The fP 2400Q is a lightweight and space-saving four-channel power amplifier, ideal for
use in high quality touring sound systems as well as in demanding permanent installations.
The fP 2400Q offers a diverse choice of applications, such as: multi-channel monitor
systems, four-channel reproduction, and compact amplification in active 2-, 3-, and 4-way
systems.
The fP 2400Q makes possibile the bridge connection of one or two of the two pairs of
channels (channel A and B and/or channel C and D). It also features Lab.gruppen?s unique
power matching solution, the MLS switch, which offers endless combinations for solving
most of the problems related to varying impedances and maximum power capacities of
loudspeakers. The latest semiconductor technology is utilized in the new ferrite Power (fP)
amplifiers.
This, together with Lab.gruppen?s proprietary copper cooling system, Intercooler?, enhances
the 2 ohms capacity. Two easily accessible dust filters on the front ensure a clean front-to-rear
airflow. Additionally, a new Bi-phase wiring scheme also increases the capacity of the switch
mode power supply. This extends the power bandwidth in the low end.
Key Features:
4 x 370 watts @ 8 ?
4 x 380 watts @ 4 ?
4 x 500 watts @ 2 ?
(Measured just below clip level, with all 4 channels driven)
Light weight and compact: only 8.6 kg (19lbs), 2U high
MLS? Switch: Lab.gruppen?s unique power matching for different loads
New Features:
Replaces the LAB 1200C
Easily accessible dust filters
Improved low-end power bandwidth
Extruded front panel for increased stability
Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of features
to make the fP family functional in all situations from installation to high performance live
sound systems:
Regulated switch mode power supply
Today there are many lightweight, switch-mode amplifiers in the market. However, the unique
Lab.gruppen switch-mode power supply technology offers a number of essential advantages
that make it superior to other and seemingly similar power supply designs. The most important
features are the regulated power supply and the extreme power efficiency. The regulated power
supply easily deals with a very high variation in the AC mains voltage: it can drop by up to 20%
below its nominal level - e.g. to 180 V instead of 230 V ? without any problem. Perhaps even
greater benefits result from the extreme efficiency of Lab.gruppen amplifiers: only a fraction of the
energy from the AC mains is turned into heat.
A regulated power supply also presents some other sonic advantages, such as better cone control
and the same fast response as a conventional power supply.
Sophisticated protection circuitry, combining:
ALS? short circuit protection; the Adaptive Limiting System permits very high peak currents, but
keeps the amplifier within the Safe Operation Area
DC protection; protects against infrasonic signals
VHF protection; protects the loudspeakers against strong very high frequency non-musical signals
above the audible range
Thermal protection; prevents the amplifier from being overheated. The protection indicators on the front
panel are switched on, as a warning, before the protection process is initiated
AC protection; shuts down the power supply if the line voltage is outside the operating voltage
Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining
full peak power. |
The C 16:4 is one of two mid-power, four-channel amplifiers in the C Series family. Attractively packaged in a 2U chassis, it provides 4 × 400 W output into 4 ohm loads.
C Series amplifiers are uniquely capable of adapting to a wide variety of demanding load conditions. Each channel has an individually configurable Voltage Peak Limiter (VPL™), which allows the output to be optimized for any loudspeaker load – whether a single large subwoofer or a series of small 100/70 V loudspeakers. VPL works in combination with adjustable input gain to achieve maximum headroom regardless of input levels or output impedances.
Every C Series is ready for the NomadLink® network right out of the box. With NomadLink, key amplifier parameters are displayed via DeviceControl software, and remote control of channel mutes and power on/off is under network control.
Specifications C 16:4
General
Number of channels 4
Peak total output all channels driven 1600 W
Peak output voltage per channel 141 V
Max. output current per channel 8.5 Arms
Max. Output Power 16 ohms 8 ohms 4 ohms 2 ohms Hi-Z
Per ch. (all ch.’s driven) 400 W 400 W 300 W n.r. 400 W (70 Vrms / 100 V peak)
Bridged per ch. 800 W 600 W n.r. n.r. 800 W (140 Vrms / 200 V peak)
Performance with Gain: 35 dB and VPL: 100 V
THD 20 Hz - 20 kHz for 1 W 70 dB
Frequency response (1 W into 8 ohms) +0/-3 dB 6.8 Hz - 34.2 kHz
Input impedance 20 kOhm
Input Common Mode Rejection, CMR 50 dB
Output impedance @ 100 Hz 30 mOhm
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch. 3) 141, 118, 100, 85, 71, 59, 50, 42 V
VPL, selectable when bridged 3) 1) 282, 236, 200, 170, 142, 118, 100, 84 V
Voltage Peak Limiter mode (per ch.) Hard / Soft
Gain and Level
Amplifier gain selectable (all channels) 1)
– rear-panel switches
23, 26, 29, 32, 35, 38, 41, 44 dB
Default gain 35 dB
Level adjustment (per ch.) Front-panel potentiometer, 21 position detented from -inf to 0 dB, hidden behind security panel/dust filter grille
Connectors and switches
Input connectors (per ch.) 3-pin Phoenix, electronically balanced
Output connectors (per ch.) Barrier strip 2-pole screw terminals
Output bridge mode A+B and/or C+D, inputs A and C are input source
NomadLink® network On board, 2 x RJ45 connectors
Intelligent fans (on/off) Yes, depending on presence of output signal
Power on/off and Remote enable on/off Individual switches on front-panel
Cooling Two fans, front-to-rear airflow, temperature controlled speed
Front-panel indicators
Common NomadLink® Network; Power Average Limiter (PAL) 2); Power on
Per channel
Signal present / High-impedance; -10 dB and -4 dB output signal; Voltage Peak Limiter (VPL); Current Peak Limiter (CPL);
Very High Frequency (VHF); High Temperature; Fault; Mute
Power
Operating voltage, 230 V / 115 V nominal 130 -265 V / 65-135 V
Minimum power-up voltage, 230 V / 115 V 171 V / 85 V
Power Average Limiter (PAL) 2) Yes
Soft start / Inrush current draw Yes / max. 5 A
Mains connector 230 V CE: 16 A, CEE7; 115 V ETL: 20 A / NEMA 5-20P
Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), D: 343 mm (13.5”)
Weight 12 kg (26.4 lbs.)
Finish Black painted steel chassis with gray painted steel front
Approvals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC
Note 1): Automatic -6 dB gain compensation when bridging channels. Ch.’s A+B and/or C+D, can be bridged individually.
Note 2): PAL can reduce the maximum output power to keep the power supply operating safely, and/or to prevent excessive current draw tripping the mains breaker.
Refer to Operation Manual.
Note 3): For sine waves, peak voltage output values translate to Vrms with the formula V/1.41 = Vrms. E.g. 100 V peak equals app. 70 Vrms.
Hence, outputs can be set for high-impedance loads without requiring a transformer.
All specifications are subject to change without notice.
| • Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
| |
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
| RMS, 1kHz, 1.0% THD+N |
|
|
|
|
| 4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
| 8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
| Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
| Pink Noise 12dB CF |
|
|
|
|
| 4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ | POWER AMPLIFIER 4 X 2100 WATT / 4Ω
Very high power and channel density – • The four-channel FP
10000Q delivers a total of 10000 W (4 x 2500 W @ 2 ohms) in
only 2U
Four-channel fexibility – • Four channels in one cabinet increases
effciency, fexibility and value in powering monitor systems, line
arrays, and bi- or tri-amped systems. Adjacent channels bridgeable
for 2- or 3-channel operation
Lab.gruppen sound quality – • FP 10000Q amplifers maintain
the impeccable sonic performance standards set by the original fP
Series, with the same durability and even greater effciency
NomadLink • ® network ready – Monitoring and control of key
functions accessible via the intuitive DeviceControl software and
the robust, daisy-chained NomadLink® network
Patented Class TD amplifer topology – • Road-proven output
stage delivers Class B audio quality with Class D effciency
Regulated Switch Mode Power Supply (R.SMPS) – • Output
power remains constant even with signifcant drops in the mains
voltage
Effcient cooling system – • Unique, lightweight Intercooler® cop-
per cooling system dissipates more heat to allow extended peak
output
Adjustable parameters – • Selectable Gain, scalable Voltage Peak
Limiter (VPL), and bridge-mode operation allow custom confgura-
tion for any system or application
XLR input connectors •
Heavy-duty binding post or Speakon output connectors •
Comprehensive protection and warning – • Excessive output
current, DC, high temperature, very high frequency (VHF), short
circuit, open load, mains fuse protection, and soft start |
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuit. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Rated ouput power (1kHz @ 4 Ohms)
4 x 810 W
Rated ouput power (1kHz @ 8 Ohms)
4 x 490 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
2 x 1600 W
Frequency response
20 - 20000 Hz
Total Harmonic Distortion (THD)
< 0.1 %
Signal-to-noise ratio
105 dB
Input sensitivity
0.775 V
Protection circuits
DC protection , short circuit , thermal overload
Controls
4 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
Limit , Power , Protect (protection circuit engaged) , Signal
Speaker output connections
Speakon compatible
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
|
Reviews
There are no reviews yet.