Content | MG05 Replacement ceramic cartridge suitable with ION CZ800-10, Numark Cr-800 and more
This replacement ceramic cartridge is a perfect fit for your Classic LP, iPT01, iPTUSB, iPTUSB LE, Max LP, or Mobile LP and many other ION turntables (see list)
To Replace Stylus
- Grasp both sides of the stylus and pull forward to remove stylus
- Grasp both sides of the stylus and slide up and back to attach stylus
To Replace Cartridge
- Remove stylus from old Cartridge
- Grab headshell with thumb under front tab and index finger on rear of head shell with left hand.
- Grab old cartridge with right thumb and index finger. Carefully Pull down and forward with right hand while while pulling up with left hand.
- Carefully disconnect wires from rear of cartridge pulling from metal tabs.
- Remove stylus guard and stylus from new cartridge
- Connect wires on new cartridge. the single metal connector with black wires goes on the bottom posts that are closer together.
- From rear view, as you would install the cartridge - The red wire goes on the right upper post, the white wire goes on the left upper post.
- Reconnect cartridge to headshell by placing cartridge beneath headshell with thumb below cartridge and index finger on top of headshell.
- Carefully squeeze the two together. a 'light' snap occurs and the cartridge should fit snug.
- Reattach new stylus to new cartridge.
Fits all ION turntables that use a ceramic cartridge (see following list):
- Classic LP
- Max LP
- Mobile LP
- iPTUSB
- Archive LP
- Forever LP
- Live LP
- Power Play
- Quick Play Flash
- Quick Play LP
- Vinyl Motion
- Vinyl Motion Deluxe
- Air LP
- Duo Deck
- iLP
- LP 2 GO
- CD Direct
- iProfile
- Profile LP
- Profile Pro
*TTUSB, TTUSBDC, LP2CD, Select LP use a magnetic cartridge and are not compatible.
STY146 Recommended replacement stylus for 33/45rpm | A budget cartridge that out performs a lot of other top-of-the-line models.
No need to go broke to get an affordable, tough-as-nails scratching tool.
Technical Data:
- Output voltage at 1000 Hz, 5cm/sec: 5 mV
- Channel balance at 1 kHz: 2 dB
- Channel separation at 1 kHz: 20 dB
- Channel separation at 15 kHz: 15 dB
- Frequency range at - 3dB: 20-20.000 Hz
- Frequency response: 20-18.000 Hz + 3 / - 2 dB
- FIM distortion at recommended
tracking force, DIN 45.542:
- Tracking ability at 315Hz at
recommended tracking force: 70 µm
- Compliance, dynamic, lateral: 7 µm/mN
- Stylus type: Spherical
- Stylus tip radius: R 26 µm
- Equivalent stylus tip mass: 0,5 mg
- Tracking force range: 3,0-5,0 g (30-50 mN)
- Tracking force, recommended: 4,0 g (40 mN)
- Tracking angle: 20°
- Internal impedance, DC resistance: 750 Ohm
- Internal inductance: 450 mH
- Recommended load resistance: 47 kOhm
- Recommended load capacitance: 200-600 pF
- Cartridge colour: Black
- Cartridge weight: 5 g
- Replacement stylus unit: PRO S
|
Type: MC-type
Playback frequency range: 15-50,000Hz
Output voltage: 0.3mV (1kHz and 3.54cm/sec.)
Channel separation: 30dB (1kHz)
Output balance: 0.5dB (1kHz)
Stylus pressure: 1.8-2.2g (2.0g standard)
Coil impedance: 10O (1kHz)
DC resistance: 10O
Load resistance: More than 100O (when head amp connected)
Coil inductance: 22µH (1kHz)
Static compliance: 40×10-6cm/dyne
Dynamic compliance: 10×10-6cm/dyne (100Hz)
Stylus needle shape: Oval (0.3×0.7mil)
Cantilever: Duralumin tapered pipe
Vertical tracking angle: 23°
Dimensions: H16×W16.6×D26.5mm
Weight: 6.9g
Accessories: Non-magnetic screwdriver × 1, Washer × 2, Protector × 1, Cartridge installation screws 13 mm × 2 and 19 mm × 2, Nut × 2, Brush × 1, PCOCC lead set × 1
| THE CARL COX SIGNATURE MODEL, OPTIMIZED FOR DANCE MUSIC DJ PERFORMANCE.
* Frequency response: 20 to 22,000Hz
* Output: 6mV
* Channel separation nominal: 32dB
* DC resistance: 430 ohms/ch
* Inductance: 400mH/ch
* Weight: 18.0g
* Channel balance: within 1.5dB
* Tracking force: 3–6g
* Recommended load: 47K ohms 200pf
* Stylus tip: fine circular diamond
* Application: club and mobile DJs, high output |
For DJs that require increased tracking ability, the Scratch is up to the task. Featuring a reinforced rubber suspension, DJs need not worry about compromising sound quality and stylus life when working with higher tracking forces. With solid bass reproduction and extended highs, the Scratch is great for any style, providing energetic, in-your-face sound.
Output voltage at 1000Hz, 5cm/sec.
|
7 mV
|
Channel balance at 1kHz
|
1,5 dB
|
Channel separation at 1kHz
|
25 dB
|
Channel separation at 15 kHz
|
15 dB
|
Frequency range at -3dB
|
20-20.000 Hz
|
Frequency response
|
20-15.000 Hz 3dB/-2dB
|
Tracking ability at 315 Hz at recommmende tracking force
|
80 μm
|
Compliance, dynamic lateral
|
6 μm/m N
|
Stylus type
|
Spherical
|
Stylus tip radius
|
R 18 μm
|
Tracking force range
|
3,0-5,0 g (30-50 mN)
|
Tracking force recommended
|
4,0 g (40 mN)
|
Tracking angle
|
20°
|
Internal impedance, DC resistance
|
750 Ohm
|
Internal inductance
|
450 mH
|
Recommended load resistance
|
47 kOhm
|
Recommended load capacitance
|
200-600 pF
|
Cartridge weight
|
5 g
|
Replacement stylus unit
|
scratch
|
| The 2M series were developed in conjunction with Danish designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a recordʼs surface, the 2Mʼs handsome elegance establishes a great combination of form and functionality.
2M are designed for precise and accurate retrieval of the information in the record groove. Our philosophy is to play the record sound as accurate as possible, without coloring the sound. We have optimized the design for ease of mounting the cartridge, weight and size to fit the most common turntables at the market today.
The name 2M was selected among several ideas. We wanted a modernname which should be easy to pronounce and to remember, and therefore an alpha numerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.
Of course the 2M isnʼt just another pretty face. It has been engineered to the highest standards and is congruent with Ortofonʼs unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.
The 2M series of cartridges feature Ortofonʼs trademark split pole pins, an invention which enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series. The 2M Red uses an improved engine, which provides an increased output of 5.5mV. 2M red features a tipped elliptical diamond.
TECHNICAL DATA |
|
Output voltage at 1000 Hz, 5cm/sec. |
5,5 mV |
Channel balance at 1 kHz |
1,5 dB |
Channel separation at 1 kHz |
22 dB |
Channel separation at 15 kHz |
15 dB |
Frequency range at - 3dB |
20-22.000 Hz |
Frequency response |
20-20.000 Hz + 3 / - 1 dB |
Tracking ability at 315Hz at recommended tracking force |
70 µm |
Compliance, dynamic, lateral |
20 µm/mN |
Stylus type |
Elliptical |
Stylus tip radius |
r/R 8/18 µm |
Tracking force range |
1,6-2,0g (16-20 mN) |
Tracking force, recommended |
1,8 g (18 mN) |
Tracking angle |
20° |
Internal impedance, DC resistance |
1,3 kOhm |
Internal inductance |
700 mH |
Recommended load resistance |
47 kOhm |
Recommended load capacitance |
150-300 pF |
Cartridge colour, body/stylus |
Black/Red |
Cartridge weight |
7,2 g |
Replacement stylus unit |
2M Red |
|
Reviews
There are no reviews yet.