Content | TONAR DIAMOND 387DS
For Shure Cartridges M 44C High Quality Stylus Conical Diamond for Turntable. N75B Type 2 or DN325, Luxor 3823 was earlier called N75-6 Type 2. This popular stylus type is widely used for M75-6, M75-6S, M75-6 Type 2, M75B Type 2 and M75 Type D. Recommended tracking force is 1,5g to 3g.
Specs:
- Stylus N 75 ED Type II
- Elliptical Diamond Tip 0.3 x 0.7 mil
- Tracking Force: 2.0 – 2.5 grams tracking pressure
- Stylus Color: Black or Yellow
For Cartridges: M75G, M75B, M73, M71, M71MC, M73, M75ED, M75EJ, M75E, M75HE, M44MB, M44C, M44MC, M55, M44E, M44EM, M44MA, M44MB, M44MF, M80EM98, M98/A, M99, Shure AMC50E.
For Needles: N75E, N75EC, N75ED, N75EJII, N75, N75C,
Fits the following Turntables models: Garrard DD 130, DD 131, DD 132, DD 132 LX, DD 139, DD 75, GT 35 P, Luxor 3823, Dual 1009, 1016, 1019, Schneider DN-325 and more
Note: This needle was installed on the following turntable models when they were sold.
If the original cartridge has been replaced with a different type, this needle won’t fit.
Match your old needle to the picture before you make a purchase.
This stylus was used in the following turntables:
The stylus is used in the following turntable cartridges: M 75
Fits also for N75E, N75EC, N75ED, N75EJII | Replacement stylus for the Carl Cox Signature CS-1 Cartridge.
* Frequency response: 20 to 22,000Hz
* Output: 6mV
* Channel separation nominal: 32dB
* DC resistance: 430 ohms/ch
* Inductance: 400mH/ch
* Weight: 18.0g
* Channel balance: within 1.5dB
* Tracking force: 3–6g
* Recommended load: 47K ohms 200pf
* Stylus tip: fine circular diamond
* Application: club and mobile DJs, high output | Stylus 2M Red
Technical data |
|
Frequency range |
20-22.000 Hz |
Frequency response |
20-20.000 Hz + 3 / - 1 dB |
Tracking ability at 315Hz at recommended tracking force *) |
70 µm |
Compliance, dynamic, lateral |
20 µm/mN |
Stylus type |
Elliptical |
Stylus tip radius |
r/R 8/18 µm |
Equivalent stylus tip mass |
0,5 mg |
Tracking force range |
1,6-2,0 g (16-20 mN) |
Tracking force, recommended |
1,8 g (18 mN) |
Tracking angle |
20° |
Stylus colour |
Red |
|
|
Recommended for following cartridges |
2M Red |
*) Typical value |
Stylus 5 Spherical
Technical data |
|
Frequency range |
20-20.000 Hz |
Frequency response |
20-15.000 Hz ± 2 dB
|
Tracking ability at 315Hz at recommended tracking force *) |
60 µm |
Compliance, dynamic, lateral |
15 µm/mN |
Stylus type |
spherical |
Stylus tip radius |
R/18 µm |
Equivalent stylus tip mass |
0,5 mg |
Tracking force range |
1,75-2,25 g (17,5-22,5 mN)
|
Tracking force, recommended |
2 g (20 mN)
|
Tracking angle |
20° |
Stylus colour |
Black |
|
OM 5,OMB 5, LMA 5, SMB 5 |
*) Typical value |
Stylus 10
Genuine Original Stylus for OM 10, OM 10 Super, OMP10, LM 10, Concorde 10, TM 10H
Elliptical
Interchangeability/Upgrade Group: A
|
DJ E Replacement stylus
Basic model for scratch and back-cueing. Outstanding rigidity by extra-strengthened cantilever
Features Special Elliptical stylus and a special developed and extremely balanced cantilever.
Not only does the cartridge have a most sufficient tracking ability, it is also nearly unbreakable and provides the DJs with the most needed stringency. Furthermore, it equals very low record wear, an advantage for busy DJ.
The DJ series has been known to many as the "jack of all trades," with improved tracking, alongside of accurate sound reproduction. Featuring a low wear stylus design, the DJ provides excellent groove handling, even with less weight applied.
DJ E Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 6 mV Channel balance at 1kHz - 2 dB Channel separation at 1kHz - 23 dB Channel separation at 15 kHz - 15 dB Frequency range at -3dB - 20-22.000 Hz Frequency response - 20-20.000 Hz +/-2 dB Tracking ability at 315 Hz at recommmende tracking force - 80 μm Compliance, dynamic lateral - 9 μm/m N Stylus type - Special Elliptical Stylus tip radius - r/R 13/25 μm
Tracking force range - 2,0-4,0 g (20-40 mN) Tracking force recommended - 3,0 g (30 mN) Tracking angle - 20° Internal impedance, DC resistance - 750 Ohm Internal inductance - 450 mH Recommended load resistance - 47 kOhm Recommended load capacitance - 200-600 pF Cartridge weight - 18,5 g
Compatible with cartridges - DJ S
|
Reviews
There are no reviews yet.