| Content |
- Three-channel tabletop mixer
- Inputs: two phono/line switchable (RCA), four line (RCA), mic (1/4“)
- Outputs: Master (RCA), Record (RCA), headphone (1/4" stereo)
- Steep three-band EQ/rotary kills on each channel
- Microphone input with EQ
- Six-segment LED display for monitoring signal strength
- Toggle for master and PFL metering
- Replaceable crossfader with reverse and slope controls
Inputs:
- Line: 10K ohm input impedance; 80mV RMS sensitivity for 0dB output
- Mic: 600 ohm input impedance unbalanced; 1.5mV RMS sensitivity for 0dB output; 400mV RMS max input
- Phono: 47k ohm input impedance; 1.3mV RMS sensitivity @ 1kHz for 0dB output
Outputs:
- Line: 7V RMS max
- Headphone: 0.5W into 47ohm
Signal to Noise Ratio (maximum output JIS-A weighted):
- Line: Better than 100dB
- Mic: Better than 95dB
- Phono: Better than 85dB
Distortion: Less than 0.05%
Frequency response:
- Line: 20 – 20,000 Hz ±0.5dB
- Mic: 20 – 15,000 Hz ±0.5dB
- Phono: ±1dB; -3dB attenuation at 20 Hz to reduce rumble and feedback
Channel Equalizer:
- Bass: +12 / -35dB at 20 Hz
- Mid: +12 / -25dB at 1.3 kHz
- Treble: +12 / -20dB at 15 kHz
Channel fader kill: Better than 90dB at 1 kHz
Crossfader kill: Better than 75dB
Crosstalk: Better than 80dB at 1 kHz |
- 6 input channels
- MIC (XLR3) inputs on channels 1 and 2
- MIC (JACK ¼”) / stereo LINE (RCA) in channels 3 and 4. Input signal pushbutton selector (MIC/LINE) on back panel
- Stereo LINE (RCA) on channels 5 and 6
- Input signal gain level control (accessible only with screwdriver)
- Each channel features signal present (SP) and CLIP indicators
- General phantom power switch located on back panel. Independent internal phantom power assignment to any MIC input
- Triple tone control (accessible only with screwdriver)
- 2 main stereo OUTPUTS (XLR3) with independent volume control
- 3 LED OUTPUT level meter
- Input channels can be routed to any main output (A,B) or both
- 2 additional stereo REC outputs (REC1, REC2)
- Mono mode selector in outputs A and B
- Headphones monitoring of selected output (A or B)
- Integrated, internally configurable talkover. Affects OUT A and REC A
- Remote MUTE function (PHOENIX) allows linking to external fire detection centrals
- TALKOVER function fully configurable to –20dB or –30dB that affects boths outputs A and REC A
The SAM mixer series has been specially designed for all public address and communication systems requiring a minimum risk of unwanted external manipulation.
Frequently used controls are easily accessible. Specific adjustments remain only accessible by the installer for precise and permanent settings.
SAM SERIES are very easy to use, even for non-technical users. All this is packed into a compact, 1 unit high, 19'' rack unit.
SAM series general KEY features
- Universal 1 RU, 19” installation mixers
- Excellent frequency response
- Balanced MIC and stereo LINE inputs and main outputs
- Reliable proprietary power supply
- Ideal for any application requiring a trouble free mixer
| PowerMate 1000
SPECIFICATIONS
Order No.
F01U131113 (DC-PM1000-3-UNIV)
Channels (Mono + Stereo)
6 + 4
Auxiliaries (MON, FX, AUX)
2 Pre, 2 Post, 2 Pre/Post switchable
Maximum Midband Output Power,1 kHz, THD=1%, Dual Channel
into 2.66 Ohms
2 x 1350 W
into 4 Ohms
2 x 1000 W
into 8 Ohms
2 x 600 W
Rated Output Power,THD=0.1%, Single Channel
into 4 Ohms
2 x 900 W
into 8 Ohms
2 x 450 W
Maximum Output Voltage of power amplifier, no load
74 Vrms
THD at 1kHz, MBW=80kHz
MIC input to Master A L/R output, +16 dBu, typical
< 0.005%
POWER AMP INPUTS to Speaker L/R output
< 0.075%
DIM 30, power amplifier, 60Hz, 7kHz
< 0.05%
IMD-SMPTE, power amplifier, 60Hz, 7 kHz
< 0.015% CMRR, MIC input, 1 kHz > 80 dB
Equivalent Input Noise, MIC Input, A-weighted, 150 Ω
-130 dBu
Signal/Noise-Ratio, power amplifier, A-weighted, 4 Ohms
105 dB
Output Stage Topology, amplifier
Class D
Equalization
LO Shelving
+/- 15 dB / 60 Hz
MID Peaking, mono inputs
+/- 15 dB / 100 Hz .. 8 kHz
MID Peaking, stereo inputs
+/- 12 dB / 2.4 kHz
HI Shelving
+/- 15 dB / 12 kHz
Master EQ, 11-band (63, 125, 250, 400, 1k, 1.6k, 2.5k, 4k, 6.3k, 12k Hz)
+/- 10 dB / Q = 1.5-2.5
Filter
LO-CUT, mono inputs
f=80 Hz, 18 dB/oct
VOICE FILTER, mono inputs
FEEDBACK FILTER, MON1/2
70 Hz .. 7 kHz, Notch, -9 dB
Speaker Processing
LPN, switchable
Display
High Contrast OLED
Effects | Behringer Micromix MX-400 Ultra Low-Noise 4-Channel Line Mixer
Despite its ultra-compact size, this 4-channel line mixer is big on features! It yields the highest sonic quality at all output levels, boasting ultra low-noise 4580 operational amplifiers for outstanding audio performance?the same op amps found in its much bigger brethren. Expanding on the capabilities of standard-size mixers is where the MX400 does extremely well, for example as a sub-mixer. If you are running short on available channels on your ?big? mixer and need to bring the output of three different keyboards into your mix, you can simply connect them to the MX400, work out the keyboard mix, and connect the MX400?s output to a single input on your main mixer.
It will catch your eye because it?s cute as a button, but you?ll want to own one because of what it can do for your performance.
- Compact 4-channel line mixer
- Separate volume control for each channel
- Low noise 4580 operational amplifier
- 4x 6.3 mm Mono jack inputs
- 1x 6.3 mm Mono jack outputs
- Includes 12-Volt power supply
- Dimensions: 46.5 x 57.2 x 103.6 mm
- Weight: 190 g
| 3-Channel All-Purpose Mixer with USB flash drive input
Specifications:
1. 2 line in/ phono + 1 USB
2. Mic X 2
3. headphones output
4. USB player
5. led screen + output meter |
- 3 MIC (JACK ¼”) / stereo LINE (RCA) input channel mixer
- Input signal pushbutton selector (MIC/LINE) on back panel
- Independent internal assignable phantom power for all MIC inputs
- Direct MIX input allows straight forward connection of further mixers
- Triple tone control (accessible only with screwdriver)
- 2 stereo OUTPUTS (XLR3 / RCA)
- 3 LED OUTPUT level meter
- 2 additional stereo REC outputs (REC1, REC2)
- Mono mode pushbutton
- Headphones general MIX monitoring
- Remote MUTE control (EUROBLOCK) allows connection with fire detection systems
The SAM mixer series has been specially designed for all public address and communication systems requiring a minimum risk of unwanted external manipulation.
Frequently used controls are easily accessible. Specific adjustments remain only accessible by the installer for precise and permanent settings.
SAM SERIES are very easy to use, even for non-technical users. All this is packed into a compact, 1 unit high, 19'' rack unit.
SAM series general KEY features
- Universal 1 RU, 19” installation mixers
- Excellent frequency response
- Balanced MIC and stereo LINE inputs and main outputs
- Reliable proprietary power supply
- Ideal for any application requiring a trouble free mixer
|
Reviews
There are no reviews yet.