OMNITRONIC LH-045 1-channel microphone preamplifier

• 1 microphone, XLR (bal.) or 6.3 mm jack (unbal.)
• Gain control, 10 steps (6-50 dB)
• Phantom power can be switched on
• Clip LED
• 1 line output, XLR (bal.) or 6.3 mm (unbal.)
• Operation via supplied power unit

 The OctaMic II provides 8-Channel 192 kHz / 24 bit AD conversion with eight hi-class microphone and line pre-amplification channels, featuring a combination of sophisticated components and approved RME technology.

Lowest distortion, excellent signal to noise ratio and perfectly linear frequency response transmit and amplify the microphone signals truly unchanged.

The OctaMic II includes some significant enhancements compared to the OctaMic:

The balanced TRS inputs of the Neutrik Combo XLR jacks are phantom power-free and can be operated as real line inputs too. The improved design of the input circuits allows for a maximum input level of +21 dBu with a convenient gain range from 6 dB up to 60 dB.
Improved signal to noise ratio (SNR) ADC 107.5 dB
Improved THD, especially at higher gains
Optimised heat dissipation by a new and larger housing with improved convection
Internal wide range power supply with line filter, insensitive to voltage fluctuations
Super-stable, short circuit proof 48 V phantom power


Features

OctaMic II offers 8 balanced XLR mic / line inputs via Neutrik XLR/TRS combo jacks. Each channel contains switches for 48V phantom power, a low cut filter and phase reversal. Amplification can be set between 6 and 60 dB. LEDs for signal, clip, and activated phantom power give a complete overview on the unit's status. When the special Clip Hold mode is activated, any detected clip-state will cause the corresponding LED to flash once per second. With this, the user gets a long-term peak detection, and no longer needs to constantly watch the LEDs. At the same time momentary overloads are still displayed correctly.

Frontside switches include power on/off and output level, for a choice of -10 dBV, +4 dBu or Hi Gain (+19 dBu) as reference level. This unusual feature offers two advantages. First, the reference level can be easily switched to match any of RME's current interface devices, from HDSP 9632 through Multiface up to the renowned ADI-8 series converters. Second, the Signal to Noise ratio is optimized, and the Clip-LED will exactly match the ones of the ADI-8 (2 dB below 0 dBFS).

The balanced line level output signal is available at the back of the unit via 8 stereo TRS jacks. The specially developed, internal hi-performance switch mode power supply lets the OctaMic II operate in the range of 100V to 240V AC. It is short-circuit-proof, has an integrated line-filter, is fully regulated against voltage fluctuations, and suppresses mains interference.

Top
AD-Conversion

The 8-Channel AD-conversion of the OctaMic II operates at up to 192 kHz. The digitized signal is available simultaneously at the double ADAT output (S/MUX, up to 96 kHz), and at a DB-25 connector (4 AES/EBU outputs, up to 192 kHz). The digital part can be clocked internally (master) and externally via word clock, AES/EBU and SPDIF.

RME's outstanding SteadyClock(TM) ensures perfect AD-conversion, as jitter on the external sync-sources is nearly completely removed. All settings are done via DIP-switches on the back of the OctaMic II. Analog outputs and both digital outputs operate fully simultaneously. The choice of reference level affects the analog outputs only, the signal/clip indication and the AD-conversion will react only to the Gain-pots.


Top
Tech Specs

8 balanced XLR/TRS mic/line inputs

54 dB gain range

Input impedance: XLR 2 kOhm, TRS 5 kOhm

Analog input level: from -40 dBu up to +21 dBu

Maximum output level: +21 dBu

Output impedance: 75 Ohm

Output level switchable Hi Gain / +4 dBu / -10 dBV

Signal to noise ratio (SNR): 129 dB EIN @ 150 Ohm

THD:
Large frequency range (200 kHz) with special EMI input filtering

Frequency response -0.5 dB: 5 Hz - 200 kHz

Hi-pass filter: 80 Hz, 18 dB/oct.

Line Out: 1/4" TRS (6.3 mm stereo jack), servo-balanced

Phantom power: +48 Volt switchable per channel

Internal wide range switching power supply 100-240 Volt AC

Unbeatable price/performance ratio!

AD conversion

SNR: >110 dB(A)

Supported sample rates: 28 kHz - 200 kHz

THD:
Sync Sources: AES/EBU (also SPDIF coaxial), wordclock, internal

SteadyClock(TM) ensures best sound quality even with jittery external clocks


Top
Accessories

Digital breakout cable Pro, AES/EBU, D-sub25 to 4x XLR-3 female + 4x XLR-3 male, 1m/3m/6m (ALVA Audio)
Digital D-sub cable, AES/EBU, D-sub25 male to D-Sub25 male, 1m/3m/6m (ALVA Audio)
Optical ADAT Toslink cable 1m/2m/3m/5m/10m (ALVA Audio)
Word Clock cable, 1 x BNC male to 1 x BNC male, 1m/5m/10m (ALVA Audio)

Top
Add-On

BOB-32    Universal Breakout Box with 2 x 8 XLR to 2 D-sub connectors (supports TASCAM and YAMAHA format), flip-frame case

The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.

The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.

The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.

The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.

The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.

The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.

The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
-  LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme.

At PreSonus, weʼve been designing preamps for a long time, and we always focus on audio quality first. So when we decided to upgrade our popular TubePre V2, we focused on improving an already high-quality sound—without jacking up the price. Like the originalTubePre, the new version is a fully professional tube preamp, with a dual-servo (no capacitors) gain stage that lets you boost the program signal to smoking hot levels without significantly increasing the background noise. Discrete components and high-voltage operation offer dynamic range and detail not found in other single-channel tube preamps in its class.

Housed in a rugged case, the TubePre V2 rear panel sports separate unbalanced, ¼” instrument and balanced, XLR mic inputs and unbalanced ¼” and balanced XLR line outputs. Weʼve included all of the extras you need for professional operation including a high-pass filter, phantom power for condenser mics, polarity reverse switch, and a backlit VU meter.

The PRE-73 Mk2 pre-amp and the FC3 condenser microphone in one bundle. The bundle also includes Golden Age P1 Pop Filter, Proel RSM180 mic stand and Proel CHL250 5m cable.